Razor POCKET ROCKET 155001 Owner's Manual

OWNER’S MANUAL

Read and understand this entire manual before riding!

Item Number:

155001

TM

WARNING: Riding an electric motorbike can be a hazardous activity.
Certain conditions may cause the equipment to fail without fault of the
manufacturer. Like other electric products, the Pocket Rocket can and is
intended to move, and it is therefore possible to lose control, fall off and/or
get into dangerous situations that no amount of care, instruction or expertise
can eliminate. If such things occur you can be seriously injured or die, even
when using safety equipment and other precautions. RIDE AT YOUR OWN
RISK AND USE COMMON SENSE.

This manual contains many warnings and cautions concerning the
consequences of failing to maintain, inspect or properly use your electric
motorbike. Because any incident can result in serious injury or even death, we
do not repeat the warning of possible serious injury or death each time such a
possibility is mentioned.

APPROPRIATE RIDER USE AND PARENTAL SUPERVISION

This manual contains important safety information. It is your responsibility to
review this information and make sure that all riders understand all warnings,
cautions, instructions and safety topics and assure that young riders are able
to safely and responsibly use this product. Razor USA recommends that you
periodically review and reinforce the information in this manual with younger
riders, and that you inspect and maintain your children’s vehicle to insure their
safety.

The recommended rider age of 12 years is only an estimate, and can be
affected by the rider’s size, weight or skills. Any rider unable to fit comfortably
on the Pocket Rocket should not attempt to ride it.

A parent’s decision to allow his or her child to ride this product
should be based on the child’s maturity, skill and ability to follow
rules.

Keep this product away from small children and remember that this product
is intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the vehicle.

DO NOT EXCEED THE WEIGHT LIMIT OF 170 pounds. Rider weight does not
necessarily mean a person’s size is appropriate to fit or maintain control of the
Pocket Rocket.

Do not touch the brake or electric motor on your electric motorbike when in
use as they can become very hot.

Refer to the section on safety for additional warnings.

ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the Pocket Rocket may be used.

Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.

The Pocket Rocket is meant to be used only in controlled environments free
of potential traffic hazards and not on public streets or sidewalks. Do not ride
your electric motorbike in any areas where pedestrian or vehicle traffic is
present.

Do not activate the speed control on the hand grip unless you are on the
electric motorbike and in a safe, outdoor environment suitable for riding.

This bike was manufactured for performance and durability but is not
impervious to damage. Jumping or other aggressive riding can over-stress
and damage any product, including the electric motorbike. The rider assumes
all risks associated with high-stress activity.

Be careful and know your limitations. Risk of injury increases as the degree
of riding difficulty increases. The rider assumes all risk associated with
aggressive riding activities.

Maintain a hold on the handlebars at all times.

Never carry passengers or allow more than one person at a time to ride the
electric motorbike.

Never use near steps or swimming pools.

Keep your fingers and other body parts away from the drive chain, steering
system, wheels and all other moving components.

Never use headphones or a cell phone when riding.

Never hitch a ride with another vehicle.

Do not ride the Pocket Rocket in wet or icy weather and never immerse the
electric motorbike in water, as the electrical and drive components could be
damaged by water or create other possibly unsafe conditions.

The Pocket Rocket is intended for use on dry surfaces such as pavement or
flat, level ground without loose debris such as rocks or gravel. Wet, slick,
bumpy, uneven or rough surfaces may impair traction and contribute to
possible accidents. Do not drive the electric motorbike in mud, ice, puddles
or water. Avoid excessive speeds that can be associated with downhill rides.
Never risk damaging surfaces such as carpet or flooring by use of an electric
motorbike indoors.

Do not ride at night or when visibility is limited.

PROPER RIDING ATTIRE

Always wear proper protective equipment such as an approved safety helmet
(with chin strap securely buckled), elbow pads and kneepads. A helmet may
be legally required by local law or regulation in your area. A long-sleeved
shirt, long pants and gloves are recommended. Always wear athletic shoes
(lace-up shoes with rubber soles), never drive barefooted or in sandals,
and keep shoelaces tied and out of the way of the wheels, motor and drive
system.

USING THE CHARGER

The charger supplied with the electric motorbike should be regularly
examined for damage to the cord, plug, enclosure and other parts, and in the
event of such damage, the bike must not be charged until the charger has
been repaired or replaced.

Use only with the recommended charger.

The charger is not a toy.

Always disconnect from the charger prior to wiping down and cleaning your
electric motorbike with liquid.

FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH
APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE
OPERATION.

Safety WarningS

Safety Warnings .................................................................................1

Before You Begin .................................................................................2

Assembly and Set-Up ...................................................................... 3-4

Repair and Maintenance ................................................................. 4-6

1

Troubleshooting Guide .................................................................... 7-8

Pocket Rocket Parts ....................................................................... 9-10

Safety Reminders ..............................................................................12

Warranty Information ........................................................................12

contentS

Remove contents from box. Remove the foam separators that protect the components from damage during
shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Because the Pocket Rocket was 95 percent assembled and packed at the factory,
there should not be any problems, even if the box has a few scars or dents.

Estimated Assembly and Set-Up Time

Razor recommends assembly by an adult with experience in bicycle mechanics.
Allow up to 30 minutes for assembly, not including initial charge time.
Allow up to 12 hours for initial charge (see page 3 for charging information).

BEFORE YOU BEGIN

2

WARNING:
Do not use your Pocket Rocket
for the first time until you have
charged the battery for at least
12 hours. Failure to do so may
damage your vehicle and void
your warranty.

DO NOT USE NON-RAZOR
PRODUCTS WITH YOUR RAZOR
POCKET ROCKET. The Pocket
Rocket has been built to certain
Razor design specifications. The
original equipment supplied at
the time of sale was selected
on the basis of its compatibility
with the frame, fork and all
other parts. Certain aftermarket
products may or may not be
compatible.

Required Tools

Some tools may be supplied; however, we recommend the use of mechanic’s grade tools. Use the supplied
tools only as a last resort.

Need Help? Visit our web site for updates and a list of authorized service centers at www.razor.com or call toll-free
at 866-467-2967 Monday - Friday 8:00 AM - 5:00 PM Pacific Time.

4mm and 5mm

hexagonal key wrenches

(included)

Brake Lever

Brake Lever

Adjuster

Wheel

Tire

Back Brake
Adjuster

Speed Control

Drive

Chain

Charger

Charger
Plug

Charger
Port

Bicycle-style tire pump for

Schrader valve tires, with

pressure gauge

Charger Port

Front Fork

On/Off
Switch

Circuit Breaker

Circuit
Breaker

3

ASSEMBLY AND SET-UP

1 Swing the handlebars

outward as shown. You may
have to loosen the clamps
to allow the bar to pivot on
the fork.

2 Using a 5mm hex key

wrench, tighten both the left
and right side handlebar clamps
by turning the screws clock­wise. When properly tightened,
the handlebars cannot be
twisted out of alignment.

Attaching the Handlebars

WARNING:

Failure to properly tighten both
sides may cause the handlebars
to dislodge while riding and
may cause you to lose control
and fall. When correctly
tightened, the handlebars will
not rotate out of alignment
under normal circumstances.

Charging the Battery

Your electric motorbike may not have a fully charged battery; therefore it is a good idea to charge the
battery prior to use.

• Initial charge time: 12 hours • Run time: up to 40 minutes

• Recharge time: up to 8 hours, • Average battery life: 250 charge/discharge cycles
depending on the level of depletion

1 Plug the charger port into the

port on the electric motorbike.
The charger works with the
power switch in either the on or
off position.

2 Plug the charger plug into a

wall outlet.

WARNING:
Always disconnect your electric
motorbike from the charger before
cleaning with liquid.

Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.

The charger has a small window
with one LED or two LEDs to
indicate the charge status. Refer
to the illustration on the charger
unit for the actual “charging” and
“charged” status indications for
your model charger.

Chargers have built-in over-charge
protection to prevent battery from
being over-charged.

Be sure to properly align the
groove on the charger input
plug with the corresponding
socket on the case; otherwise,
no charging action will occur.

Charger
Plug

Charger
Port

1 Remove two rubber protectors

from fairing mount. Remove two
button head screws with rubber
washers from both sides of fairing
mount.

2 Position the fairing and

align holes with holes in fairing
mount. Attach fairing to
mounting points and secure
with screws.

Attaching the Fairing

3 If you have trouble aligning

holes, put one screw in place
loosely and maneuver opposite
side into position. Tighten all
screws.