Raytec SPX-HP25K, SPX-HP20K, SPX-HP10K, SPZ-HP10K, SPZ-HP15K Installation Manual

SPARTAN

High Power Luminaire Range ­Installation Guide

SPX/SPZ

Zone 1 and 21 Variant CML 17ATEX1148 & IEC Ex CML17.0074
Zone 2 and 22 Variant CML 17ATEX4149 & IEC Ex CML17.0074
Zone 21 Dust only Variant CML 18ATEX3161 & IEC Ex CML18.0087

This installation guide provides instructions for installing the SPARTAN HP Highbay/ Flood-

light series of explosion protected oodlights.

Overview

1 Safety Instructions

2 Installation

3 Maintenance

4 Technical Specication

5 Trouble Shooting

The SPARTAN HP series of explosion protected oodlights/highbay are specialist devices,
certied for use in specic operating environments.

The units must be installed in accordance with these instructions, must be correctly certied
for the specic operating environment and must be installed by suitably qualied personnel.

If you have any queries about the installation or the certication of the unit – please contact
Raytec for immediate assistance and advice.

Important information

1050-M-00052 Rev B

2

www.raytecled.com UK / Europe Tel: [phone]

Americas Tel: [phone]

1. Safety instructions

1. Read this leaet carefully before commencing to install the SPARTAN unit and retain it
for future use. Installation can only be carried out by suitably qualied personnel.

2. Check the certication to ensure that the Zone, mains supply, ambient temperature
present and ‘T’ rating are suitable for the environment the unit is being installed in.

3. If the SPARTAN unit is to be installed in areas of high vibration, please consult with Raytec.

4. The SPARTAN unit housing is constructed from marine grade aluminium and toughened
glass, gaskets are silicone sponge, black encapsulant and o rings are silicone rubber,
inner domes on LEDs are polycarbonate. The end user must ensure that these materials

are suitable for the environment the SPARTAN unit will be installed in; Zone 1 and Zone 2

Hazardous areas.

5. Check certication nameplate on side of oodlight/highbay to ascertain type of threaded
cable entry on the luminaire. Select suitably certied ATEX/IEC Ex cable glands and
stopper plugs, these must be parallel thread, have a minimum of 5 full thread engagement
and be of a medium/ne tolerance to ISO965-1 and ISO965-3. The cable entry devices

selected must maintain the IP rating of the luminaire

6. The incoming mains cable should not exceed a temperature rise of 20°C above the
ambient conditions; select suitable cable.

7. To ensure the safety of the equipment, ensure that the ‘amepath’ on Zone 1 variants
are free from any corrosion. No repairs are possible to ameproof joints – if in doubt
please consult the manufacturer.

8. External fasteners must have a yield strength of at least 600N/mm2

9. On Zone 1 variants the LED assembly contains no user serviceable parts, the luminaire
must not be operated without all the individual LED polycarbonate covers in position, the
IP66 rating must be maintained.

!

Install in a well
ventilated area

Do not continually

stare at lamp

Isolate mains before

removing cover

1.5 m

3

www.raytecled.comUK / Europe Tel: [phone]

Americas Tel: [phone]

2. Installation

Mounting SPARTAN Unit

1. To meet the requirements of certication a MINIMUM of 2 xing points must be used,
the xing points must be suitable for the conditions of use.

2. The line diagrams below are for guidance only – units may be mounted in any orientation

Mounting HP SPARTAN Unit – Floodlight Application

4

www.raytecled.com UK / Europe Tel: [phone]

Americas Tel: [phone]

Mounting SPARTAN Unit – Highbay Application

422 (16.6")

353 (13.9")

536 (21.1")

457 (18")

13

(0.51")

33 (1.3")

172 (6.8")