Raytec SPARTAN Series, SPZ SPARTAN, SPX SPARTAN, BL24-EM, BL24-STD Installation Manual

SPX/SPZ

SPARTAN

Bulkhead Range - Installation Guide

Zone 1 variant CML 13ATEX3007 & IEC Ex CML14.0001
Zone 2 variant CML 17ATEX4231 & IEC Ex CML17.0135

This installation guide provides instructions for installing the White-Light SPARTAN series
of explosion protected oodlights.

Text in italics is specic for emergency variants.

Overview

1 Safety Instructions

2 Installation

3 Maintenance

4 Technical Specication

5 Declaration of Conformity

Important information

The SPARTAN series of explosion protected bulkheads are specialist devices, certied for
use in specic operating environments.

The units must be installed in accordance with these instructions, must be correctly certied
for the specic operating environment and must be installed by suitably qualied personnel.

If you have any queries about the installation or the certication of the unit – please contact
Raytec for immediate assistance and advice.

940-M-00069 Rev A

1. Safety instructions

1. Read this leaet carefully before commencing to install the SPARTAN Bulkhead unit
and retain it for future use. Installation can only be carried out by suitably qualied
personnel.

2. Check the certication nameplate attached to the luminaire to ensure that the

hazardous zone, mains supply, ambient temperature present and ‘T’ rating are suitable

for the environment the unit is being installed in.

3. If the SPARTAN unit is to be installed in areas of high vibration, please consult with
Raytec.

4. The SPARTAN unit housing is constructed from marine grade aluminium and toughened
glass. The end user must ensure that these materials are suitable for the environment
the SPARTAN unit will be installed in; Zone 1 or Zone 2 Hazardous areas.

5. Check certication nameplate on side of bulkhead to ascertain type of threaded cable
entry on the luminaire. Select suitably certied ATEX/IEC Ex cable glands and stopper

plugs, these must be parallel thread, have a minimum of 5 full thread engagement and

be of a medium/ne tolerance to ISO965-1 and ISO965-3. The cable entry devices

selected must maintain the IP rating of the luminaire

6. The incoming mains cable should not exceed a temperature rise of 24°C above the
ambient conditions; select suitable cable.

Isolate mains before

removing cover

2 www.raytecled.com UK / Europe Tel: [phone]

!

Install in a well
ventilated area

1.5m

Do not continually

stare at lamp

Americas Tel: [phone]

2. Installation

Mounting SPARTAN Unit

1. To meet the requirements of certication a MINIMUM of 2 xing points must be used,
the xing points must be suitable for the conditions of use.

220

182

3

Americas Tel: [phone]

302

288

204

240

220

168

70

20

121

104

17

3www.raytecled.comUK / Europe Tel: [phone]

Spartan Bulkhead 24 Floodlight Standard/Emergency Variant

Typical wiring diagram - Standard Variants

Typical wiring diagram - Emergency Variants

D

2. The unit may have been supplied with an integrated photocell. Care should be taken

when positioning the unit to ensure the sensor is not shielded, is not pointing directly

at another light source and is monitoring the general, prevailing light conditions.

3. The SPARTAN Bulkhead is supplied as standard with the mounting brackets tted as

shown on the above diagram, other mounting methods/brackets available – please
contact Raytec.

GREEN

EARTH TO SCREW

PSU

GREEN

EARTH TO SCREW

PSU

WHITE

WHITE/RED

Wire the Mains cable into the terminal block. Provision has been made for this and identied
as the E (Earth), L1 (Live switched), L2 (Live permanent) and N (Neutral) terminals. There

are two pairs of contacts for each of these to facilitate a mains cable that can be looped in

and out of the unit. The L2 terminals on a standard unit are not electrically connected but

allows them to be used on the same circuits as emergency bulkheads.

4. Installer should earth the unit separately – an internal and external earth point are

provided as standard

BROWN
BLUE

TO LED's

N E L1 L2

BLACK

BLACK

RED

FUSE

RED

WHITE

WHITE/RED

BATTERY

TO LED's

GREY
BROWN
BLUE

N E L1 L2

REMOVE LINK IF 4-CORE CABLE USE

5. Connect wires to mains supply.

6. If the unit is opened for any reason, disconnect mains – On emergency luminaires

there may be more than one mains supply

7. All SPARTAN oodlights have terminal blocks suitable for looping 4mm2 cable,

only one cable should be connected to each terminal block connection

4 www.raytecled.com UK / Europe Tel: [phone]

Americas Tel: [phone]