Raytec RAYMAX RM200, RAYMAX RM100, RAYMAX RM50, RAYLUX RL200, RAYMAX RM25 Installation Instructions Manual

Raytec Technical Support: Europe / Middle East: [phone] Americas: [phone]

Narrow angle using
Adaptive Illumination

Wide angle using
Adaptive illumination

specifications subject to change without notice

RAYMAX + RAYLUX

Installation Instructions

Raytec Technical Support: Europe / Middle East: [phone] Americas: [phone]

Standard PSU Specifications
RAYMAX Series

RM200 RM100 RM50 RM25
Input

AC 100-265
universal < 80W

AC 100-265
universal <40W

AC 100-265
universal < 20W

AC 100-265
universal < 10W

Fuse

2.5A anti-surge 2.5A anti-surge 1A anti-surge 1A anti-surge

Output

4.4A @ 13.5V 2.4A @ 13.5V 1A @ 13.5V 0.5A @ 13.5V

Adjustable Power

10% - 100% 10% - 100% 10% - 100% 10% - 100%

Weight

1.85 kg 1.65 kg 0.9 kg 0.8 kg

Dimensions
L x W x D

160 x 160 x 81 160 x 160 x 81 160 x 100 x 61 160 x 100 x 61

Drilling
Dimensions

4 x M4 holes
@ 145 x 123mm

4 x M4 holes
@ 145 x 123mm

4 x M4 holes @
145 x 63mm

4 x M4 holes @
145 x 63mm

RAYLUX Series

RL200 RL100 RL50 RL25
Input

AC 100-265
universal < 80W

AC 100-265
universal <40W

AC 100-265
universal <20W

AC 100-265
universal <10W

Fuse

2.5A anti-surge 2.5A anti-surge 1A anti-surge 1A anti-surge

Output

4.2A @ 14V 2.8A @ 14V 1.4A @ 14V 0.7A @ 14V

Adjustable Power

10% - 100% 10% - 100% 10% - 100% 10% - 100%

Weight

1.85 kg 1.65 kg 0.9 kg 0.8 kg

Dimensions
L x W x D

160 x 160 x 81 160 x 160 x 81 160 x 100 x 61 160 x 100 x 61

Drilling
Dimensions

4 x M4 holes
@ 145 x 123mm

4 x M4 holes
@ 145 x 123mm

4 x M4 holes @
145 x 63mm

4 x M4 holes @
145 x 63mm

Premium PSU Specifications

In addition to the standard functions, the Premium PSU includes 12v dc power and photocell followin g
contact. See diagram below for connections.

All standard PSU’s provide current controlled output specifically calibrated for the LED head. The power supplies feature
adjustable power, adjustable photocell and telemetry input.

All standard PSU’s provide current controlled output specifically calibrated for the LED head. The power supplies feature
adjustable power, adjustable photocell and telemetry input.

Raytec Technical Support: Europe / Middle East: [phone] Americas: [phone]

Quick-Fit Installation Instructions:

LED unit Installation:

1) Ensure LED unit is installed in a well ventilated area.

2) Adjust horizontal target area of the LED by adjusting circular mounting bracket.

3) Adjust vertical target area of the LED by loosening the two side screws on the central bracket before
adjusting to the required position.

4) To alter the angle of light projection using the Adaptive Illumination feature loosen the top bolt of the
lamp by a couple of rotations. Adjust the output angle of the LED units until the required illumination is
achieved then securely fasten the top bolt again.

CAUTION: DO NOT FULLY LOOSEN THE ADAPTIVE ILLUMINATION BOLT.

5) Retighten all fixings and ensure lamp is securely held in position.

6) Do not continually stare at the LED unit from less than 1.5m during operation.

7) For 200, 100 and 50 series units (RAYMAX IR and RAYLUX WL) ensure that both LED units are
connected to the PSU before turning on.

8) For 300 series units (RAYMAX and RAYLUX) ensure all three LED panels are connected to the PSU
before turning on.

9) For best results, set up should be done at night so results can be viewed on a CCTV monitor.

PSU unit Installation:

10) Ensure power supply is mounted securely to a flat external surface in a well ventilated area, externally.

11) Isolate the mains supply at all times whilst the lid is removed from the PSU.

12) Wire mains input and LED outputs as shown below. Check the legends on the PSU.

13) CAUTION: LED output is polarity sensitive. Black = negative (-ve). Red = positive (+ve).

14) CAUTION: For 200, 100 and 50 series units (RAYMAX and RAYLUX) connect both LED units before
initializing PSU.

15) CAUTION: For 300 series units (RAYMAX and RAYLUX) ensure all three LED panels are connected to
the PSU before turning on.

16) Photocell Control & Telemetry -The PSU is set-up for automatic photocell operation. If you require
external telemetry input use the terminals shown on the diagram. The photocell overrides telemetry
function so that lamps cannot be operated during the day. Telemetry input should be a zero volt, latched
input. If no external telemetry input is required, ensure there is a wire link across terminals.
Telemetry link: short circuit=lamp enabled (operated by photocell)
open circuit=lamp disbled (permanently off)

17) Photocell Adjust – The sensitivity of the photocell can be adjusted by the pot shown on the diagram. It is
factory set to approximately 20 Lux on, 40 Lux off.

18) To disable photocell operation wire both leads into one terminal. Note, do not insert a short circuit link
between the terminals.

19) Power Control – Output power of the LED unit can be controlled by adjusting the pot as shown. Each
unit is factory set to maximum power.

20) Ensure the power supply enclosure is fully sealed and watertight before operation.

Premium Functions: (Premium Power Supply Only)

18) 12v dc output is available to power camera etc. See connection diagram below. This connection is
polarity sensitive Black = negative (-ve). Red = positive (+ve). Maximum output 500mA.

19) Photocell following contact – see connections below. This is a volt free connection, but is not polarity
sensitive. Daytime = open circuit

Night-time = short circuit

Raytec Technical Support: Europe / Middle East: [phone] Americas: [phone]

Mains

In

LED

Output

x2

Additional Information for UL 1838 & CSA 22.2 No9.0

Suitable for indoor and outdoor use.
Suitable for use in wet locations.
Suitable for mounting on flammable surfaces.
Suitable for combustrible surface use.
Suitable for ambient not exceeding 35oC

Do not connect PSU to an ungrounded supply.
Do not intall within 10ft of pool or spa.
Do not use with dimmers.

Do not connect two or more power supplies in parallel.
This product must be installed by a person familiar with the construction and operation of the product and

the hazards involved, in accordance with the applicable installation code.
The device is accepted as a component of a landscape lighting system where the suitability of the

combination shall be determined by CSA or local inspection authorities having jurisdiction. Such systems
should be protected by a ground fault circuit interrupter of the Class A type.

RAYMAX and RAYLUX

25 / 50 models:

LED Outputs Polarity sensitive

Telemetry Input –
requires zero volt,
latched input

Photocell
Sensitivity
Adjust

Power
Adjust

Photocell

Main Input
100V to 240 AC

Raytec Technical Support: Europe / Middle East: [phone] Americas: [phone]

LED

Output x2

Mains In

LED

Output x3

Mains In

RAYMAX and RAYLUX

100 / 200 models:

RAYMAX and RAYLUX

300 models:

LED Outputs
Polarity
sensitive

Main Input
100V to
240V AC

Photocell

Photocell
Sensitivity

Power
Adjust

NB: The RAYMAX and RAYLUX 200 uses a different switch mode than the model shown.
The model shown is the RM100 and RL100 PSU

Telemetry Input –
requires zero volt,
latched input

Photocell following
contact – volt free, non
polarity sensitive
(Premium PSU only)

12v dc power output
(Premium PSU Only)

LED Outputs
Polarity
sensitive

Universal
100-240V AC
auto-sensing

Photocell

Photocell
Sensitivity

Power
Adjust

Telemetry Input –
requires zero volt,
latched input

Photocell following contact – volt
free, non polarity sensitive
(Premium PSU only)

12v dc power
output
(Premium PSU
Only)