Rayrun Technology RM06 User Manual

Wireless Synchronizing

4-CH LED Controller

RQ211 / RQ212

User’s Manual

Full Protection

Waterproof Option

RGBW 4-ch Output

Wireless Sychronizing

Multi-Zone Control

RF Remote Controller

Ultra Slim Design

Easy Group Setting

Introduction

Thank you for purchasing our products. RQ211 and RQ212 4­ch RGBW LED controller is designed to drive constant voltage
LED products with common anode connection in voltage range
of DC6-24V. RQ211 is master unit controlled by a RF remote,
RQ212 is slave unit synchronized with RQ211 wirelessly. User
can program them to multi-zone group by the remote, and
setup white or color lighting or synchronized dynamic modes in
different zones.

8

WHITE

OFF

MODE

ZONE

WHITE

COLOR

COLOR

+

COLOR

-

SPEEDSPEED

-

2 3

ZONE

+

ZONE

+

1

1

WHITE

2

ONLY

4

6

MODE

Zone

-

All

3

5

7

Functions

1. Turn On/ Standby

Press ‘I’ key to turn on unit or press ‘O’ key to turn off. At power
on moment, unit will automatically restore to previous status

before power cut.

2. White Mode

These two keys control white LE D working mode. Press
‘WHITE ONLY’ key, all RGB color will be shutdown and only
white LED lights up. Press ‘WHI TE OFF’ key, the white LED
will turn off and RGB LED remain it’s previous status.

3. White Brightness

Adjust white LED brightness. Press the right side key to
increase white LED brightness and the left side key to
decrease.

4. Static RGB Color Selection

These keys control the RGB static color.
a) Press color printed keys will set the RGB LEDs to
correspond color light as the key. There are 6 shortcut color
keys to make direct color selection.
b) Press ‘COLO R+’ and ‘COLOR-’ to scroll over all preset static
colors, including the 6 shortcut key colors.

5. Color Brightness

Adjust RGB color brightness. Press the right side key to
increase RGB LED brightness and the left side key to decrease.

2

6. RGB Dynamic Modes Control

These keys control the RGB dynamic modes.
a) Press ‘MOD E+’ and ‘MODE-’ key to select preset dynamic
modes.
b) Press ‘SPE ED+’ and ‘SPE ED-’ to control the dynamic
mode running speed.

7. Zone Control

Select the target zone controlled by remote. The RQ211
master unit is always zone 1 and the RQ212 slave unit can be
programmed to any zones. The remote will control the
corresponding zone(s) after the specific zone key is pressed
once. For every power up for RQ211, the zone is restored to
‘All Zone’.

8. Remote Controller Indicator

This blue indicator will blink when remote controller works.
The remote controller works at radio frequency, the signal can
pass through barrier, so it’s not necessary to aim at the
controller when operate the remote.

Installing

RQ211 and R Q212 can be programmed to a group and
operate in different zones. RQ211 is a master controller which
receives remote control signal and sends out wireless
commands to RQ212. RQ212 is slave controller and can only
be programed to RQ211 master controller for group working.
For proper wireless working, RQ212 should be in a good
wireless receiving range from RQ211.

9. Power Supply

The red power cable should be connected to power positive
and black to negative. The controller unit can work from DC
6V to 24V, Please make sure the power supply voltage is

same as the LED load and the power is capable for the load
wattage.

11

9

10

10. LED Output

RQ211/RQ212 supports constant voltage driving LED

products with common anode connection. The black cable
on the output side is the common node, it connects to the
power supply positive inside the controller. The white,
green, red and blue cable runs the driving signal of relevant
LED color, please connect the color cables to the cathode of
relevant color LED loads and the black cable to the common
node.

11. Status Indicator

This is a full color status indicator. It displays all working status
of the controller. It indicates different events as following:

Blue: normal working.
Short single white flash: new command executed.
Long single white flash: reach mode or color cycle edge.
Long single yellow flash: reach speed or brightness limit.
Red flash: overload protected.
Yellow flash: overheat protected.

Operation

12. Using Remote

Please pull out the battery insulate tape before using. The RF
wireless remote signal can pass through some nonmetal
barrier. For proper receiving remote signal, please do not
install the controller in closed metal parts.

13. Pairing New Remote

The remote and RQ211 is 1 to 1 paired as default. Further
more, one master unit can be paired to 5 remote controllers
and every remote can be paired to any master unit.
Please do following steps to pair new remote to RQ211:

1). Plug off the power of RQ211 and plug in again after 5
seconds.

2). Press remote ‘ON’ and ‘White Bright +’ key together in 5
seconds after RQ211 power on, and then press ‘RE D’ key in
another 5 seconds.
After this operation, the RQ211 indicator will flash white for
3 times to display the command is accepted, the master unit
now recognizes the new remote. Only 5 latest paired remote
controllers can be recognized by RQ211.

14. Program Slave to Zone

The RQ212 slave controllers can be programmed to zone1, 2
or 3. There’s no quantity limit in each zone group.
Do the following steps to program slave controller to master:

1). Keep the RQ211 controller power on and the remote
already paired to it.

2). Plug off the power of RQ212 slave controller and plug in
again after 5 seconds.

5

3). Press remote ‘ON’ and ‘White Bright +’ key together in 5
seconds after RQ212 power on, and then press ‘1 ZONE’, ‘2
ZONE' or ‘3 ZO NE’ key in another 5 seconds.
After this operation, the RQ212 indicator will also flash
white for 3 times to display the programming is accepted,
the slave is now programmed to the relevant zone.

Advanced Features

15. Waterproof

RQ211/212 is a standard version which can be used in dry
environments. RQ211/212-S is fully waterproof with IP68
standard, and can be used under water within depth of 30
meters.
Note: The remote receiving and master to slave
communication sensitivity will decrease when controller
installed in wet environment.

16. Protection

RQ211/212 series controllers have full protection function
for output short circuit, overload, and overheat. The controller
will automatically recover from protection when working
status is good.
Please ensure the LED loads are in rated range, outputs are
not shorted and the controller unit is in a good heat
dissipation environment to avoid protection.

6

Specification

Model

Dynamic mode

Static Color

PWM Grade

White Brightness Grade

Color Brightness Grade

Speed Grade

Direct Color Select
Overload protection
Overheat protection

Working Voltage

Remote frequency

Synchronization frequency

Remote control distance

Master/Slave sync.

Zone Control

Rated Output Current

IP Grade IP-63 IP-68 IP-63 IP-68

Caution:

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including
interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate

the equipment.

RQ211 RQ211-S RQ212 RQ212-S

6 direct keys None

433.92MHz

>15m at open area

3 zones, infinite RQ212 in each zone.

34 modes
30 colors
256 steps

10 levels

5 levels

10 levels

Yes
Yes

DC 6-24V

None

2.4GHz I SM band
None

>15m at open area

3x2.5A + 4A