Raymar V.32M/14.4, V.32M/19.2, V.34M/33.6 Specification Sheet

Alliance / Datalink Series

PENRIL MODEM FAMILY
V.34M/33.6, V.32M/19.2, V.32M/14.4

KEY FEATURES

• Universal, multimode, multispeed data and fax modems

• High performance Digital Signal Processing provides fast, flexible communications,

33.6Kbps to 300bps with DTE speeds to 230Kbps and support for 14.4Kbps fax traffic

•

Supports advanced features that maximize network uptime

• Multiple hardware versions to satisfy diverse installation requirements

• Rapid set-up for both local and remote devices

•

Continuous Data Terminal Equipment (DTE) and telephone line status reporting and

comprehensive diagnostics

• Compatible with Group 3, Class 1 and Class 2 fax and supports multiple modulation standards
and speeds for fax transmission

• Supports automatic dial backup for leased line and dial applications

• Multiple levels of network security

ADVANCED V.34 FEATURES

The Raymar-Telenetics Penril V.34 modem operates at speeds up to 33.6Kbps over the standard Public Switched
Telephone Network (PSTN) in accordance with ITU-R V.34 recommendation and over 2- or 4-wire unconditioned
leased lines. Call setup is accommodated by either ITU-R V.8 or V.25 procedures. Channel probing by the Penril V.34
automatically conditions the unit for maximum throughput and performance. Asymmetrical connection data rates allow
maximum throughput when channel directional characteristics differ. The Penril V.34 provides fallback rates in
accordance with the V.34 recommendation to accomodate channel limtis: 33.6K, 28.8K, 26.4K, 24.0K, 21.6K, 19.2K,

16.8K, 14.4K, 12.0K, 9600, 7200, 4800, 2400, 1200, 600, and 0-300 bits per second (bps).

PENRIL MODEM FAMILY: Alliance/Datalink Series

V.34M/33.6, V.32M/19.2, V.32M/14.4

INSTALLED BASE COMPATIBILITY

The Raymar-Telenetics Penril V.34 will fall back to non-V.34 modes to connect with installed base V.32terbo, V.32bis,
V.32, V.22bis, Bell 212A, V.22, V.21, and V.23 modems. Also, the Penril family of modems support ITU-T V.13 for
half-duplex simulation to work with those systems already configured for half-duplex modems. The V.29 Fast Train
(FT) mode is available for multidrop applications on all Penril modems.

FAX TRANSMISSIONS

The Raymar-Telenetics Penril modem family is compatible with Group 3, Class1, and Class 2 fax and supports
multiple modulation standards and speeds for fax transmission, including:

• ITU-T V.17 at 14.4K, 12.0K, 9600 & 7200bps

• ITU-T V.29 at 9600 & 7200 bps

• ITU-T V.27ter at 4800 & 2400bps

• ITU-T V.21 channel 2 at 300bps for T.30

Integrated support for fax traffic means that the Penril family works with standard communications software packages
to:

• Receive faxes on your computer and print faxes on a local plain paper printer

• Send faxes directly from your computer, and,

• Send data at rates up to 230.4Kbps

NETWORK MANAGEMENT

The management software built into the Raymar-Telenetics Penril modem family is compatible with Penril Communi­cations Series 6000 Network Management System. The Series 6000 provides centralized configuration, status
monitoring and diagnostic control over a network of Penril modems in any operating mode: dial-up line, leased line, or
a combination of both. The Penril reports the condition of the attached DTE port and telephone line to the network
management console for easy detection and diagnosis of network faults.

RAYMAR INFORMATION

TECHNOLOGY, INC.

7325 Roseville Road

Sacramento, CA 95842

916-783-1951

FAX [phone]

[e-mail]

1-800-695-1951

Tech Support Hotline

1-800-747-1522

www.raymarinc.com

PENRIL MODEM FAMILY: Alliance / Datalink Series
V.34M/33.6, V.32M/19.2, V.32M/14.4

PRODUCT SPECIFICATIONS

PENRIL MODEM FAMILY: V.34M/33.6, V.32M/19.2, V.32M/14.4

AUTOMATIC DIAL BACKUP

Penril modems support auto dial backup for leased line & dial applica­tions. For leased line applications, the modem monitors the received
carrier level and signal quality; in the event performance drops below
selected thresholds, Penril modems will automatically establish a dial
connection to the remote modem. Automatic loopback allows the
communications path to be returned to the leased line when conditions
permit. In dial mode, the modem will redial the number stored in any
selected memory cell in the event the connection is lost.

AT & V.25bis AUTODIALERS

Automatic call origination is provided via an AT-compatible or ITU-T
V.25bis-compliant autodialer. The AT emulation mode allows the
modem to interface with a computer or device running intelligent
communications software designed to drive an AT-style modem. The
V.25bis autodialer complies with asynchronous and synchronous
international serial call origination standards.

V.54 DIAGNOSTICS

Versatile diagnostics are supported for rapid problem isolation and
uptime maximization. ITU-T V.54 tests plus selftest can be initiated from
the units front panel via AT commands throught the DTE interface or
through the DIAG port. Penril modems support Analog Loopback
(Loop3), Analog Loopback Selftest, Analog Loopback Selftest with
Errors, Remote Digital Loopback (Loop2), and Remote Digital Loopback
Selftest. In addition to diagnostic tests, Penril modems provide numer­ous status displays for monitoring the DTE interface and telephone line
transmit and receive conditions. The status information is displayed on
the units front panel and is available remotely to minimize service calls
to remote locations.

V.42bis & MNP CLASS 5

The Penril modem family supports ITU-T V.42bis and MNP classes 1
through 5 to provide end-to-end error correction and data compression
between modems equipped with V.42bis or MNP in the asynchronous
operating mode. Error correction is provided by V.42 and MNP classes
2-4. Error correction and data compression is available in both dial and
leased line operation.

NETWORK SECURITY

Multiple levels of network security are provided by the Penril family of
modems. Penril modems can be programmed to provide manual
password protection (MPP) by calling back or passing through the
incoming caller after password validation. Automatic password protec­tion (APP) can be used in the synchronous operating mode as well.
APP provides transparent security support by incorporating the
password as part of the modem training process. Additionally, the
Penril modem can be programmed to call back the originator during the
APP security process.

SOFT SETUP

Penril modems support multiple methods of modem configuration. The
LCD and six frontpanel pushbuttons can configure the unit and
alleviate the need for internal switches. AT commands can be used to
control configuration parameters through DTE interface. There is also
a separate DIAG port through which configuration can be done from a
dumb terminal or the Series 6000 Network Management System on
both the local and remote modems.

COMPATIBLE STANDARDS

ITU-T V.34 (33.6Kbps to 19.2Kbps V.34M/33.6 only
V.32 TERBO (19.2Kpbs, 16.8Kbps) N/A V.32M/14.4
ITU-T V.32 BIS (14.4Kbps, 12.0Kbps) ALL MODELS
ITU-T V.33 (14.4Kbps, 12.0Kbps) “
ITU-T V.29 (9600, 7200, 4800bps) “
V.29FT (Fast Train) (9600, 7200, 4800bps) “
BELL 208 A/B (4800bps) “
ITU-T V.22 BIS (2400bps) “
BELL 212A (1200bps) “
BELL 103 (0-300bps) “

ALTERNATE FALLBACK CAPABILITY

ITU-T V.22 (1200bps) ALL MODELS
ITU-T V.21 (0-300bps) “
ITU-T V.23 (1200/75bps) “

FAX MODE COMPATIBILITY

ITU-T V.17 (14.4k,12.0k,9600,7200bps) ALL MODELS
ITU-T V.29 (9600, 7200bps) “
ITU-T V.27TER (4800, 2400bps) “
ITU-T V.21 CHAN 2 T.30 (300bps) “

FAX OPERATION

Class 1 ALL MODELS
Class 2 (TIA/EIA 578, preliminary EIA 2388) “

FAX OPERATION

LEASED:
Tx Level: Selectable, 0 to -15dBm ALL MODELS
CDThreshold: Selectable, -26, -33, -43dBm “
DIAL:
TX Level: Permissive or Selectable, 0 to -15dBm “
CD Threshold: Selectable, -26, -33, ir -43dBm “

WARRANTY

Raymar-Telenetics manufactured products are warranted

against defects in hardware material and workmanship under
normal use for one (1) year from date of original retail purchase.
Defective product will be repaired or replaced, determination to
be made by Raymar-Telenetics, at no charge. Repaired or
replaced products are warranted for 90 days or for original
warranty period, whichever is longer. Warranty extends to

original end-user only.

DATA RATES

Dial Modes 33.6K to 300bps V.34/33.6 only
Leased Line Modes 33.6K to 2400bps V.34/33.6 only
Dial Modes 19.2K to 300bps NA v.32m/14.4
Leased Line Modes 19.2K to 2400bps NA v.32m/14.4
Dial Modes 14.4K to 300bps ALL MODELS
Leased Line Modes 14.4K to 3500bps ALL MODELS

TELCO CONNECTION

Full Duplex over 2-Wire Dial Lines ALL MODELS
Full Duplex over 2- or 4-Wire Leased Lines “
Half Duplex “
Simulated Half Duplex V.13 “

DTE (Data Terminal Equipment) CONNECTION

RS232C/D, ITU-T V.24/28
Async: 230K to 300 bps ALL MODELS
Sync: Internal, External, or Slaved Xmit Clock ALL MODELS

PHYSICAL CONNECTIONS

2- AND 4-Wire Leased Line (RJ45S and RJ11)
2-Wire Dial Line (RJ45S)
DIAG Port (RJ45S)
RS232C/D Port (DB25S)
Power (5-pin DIN Connector, 9/9VAC 50/60Hz)
12/24/48VDC Versions Available

PHYSICAL DIMENSIONS

Stand-Alone & Full-Height Rack Mount: 2.5”H x 9.7”W x 10.1”D
Half-Height Rack Mount Models: 1.25”H x 9.7”W x 10.1”D

WEIGHT

Stand-Alone Model: 4 lb, 2 oz.
Full-Height Rackmount Model: 2 lb
Half-Height Rackmount Model: 1 lb, 8 oz

Manufactured in the USA by RAYMAR-TELENETICS

Raymar Information Technology, Inc., 7325 Roseville Road, Sacramento, CA 95842
1-800-695-1951 fax [phone] [e-mail] www.raymarinc.com
Service Support Hotline [phone]

2008 Raymar-Telenetics

©

0070-2702-000 REV:A

DHS: 09/16/2008