Page 1
040-00057-01 REV 5
Space Invaders Frenzy
Operator’s Manual
TM
©Taito Corporation 1978, 2017 All Rights Reserved
Page 2
Page 3
Space Invaders Frenzy™
Table of Contents
Safety .................................................................................................................................................................... 5
Operation .......................................................................................................................................................... 5
Transporting ...................................................................................................................................................... 5
Handling Components ...................................................................................................................................... 5
Disconnect power ............................................................................................................................................. 5
Grounding ......................................................................................................................................................... 5
Electrical Shocks ................................................................................................................................................ 5
Power Cord ....................................................................................................................................................... 5
Surge Suppressor .............................................................................................................................................. 5
Water and Other Liquid Sources ....................................................................................................................... 5
Connectors ........................................................................................................................................................ 6
Computer .......................................................................................................................................................... 6
Hazard to Epileptics .......................................................................................................................................... 6
Manual .............................................................................................................................................................. 6
Specifications .................................................................................................................................................... 6
Product Specifications .......................................................................................................................................... 7
Electrical Power ............................................................................................................................................ 7
Temperature ................................................................................................................................................. 7
Humidity........................................................................................................................................................ 7
Dimensions ................................................................................................................................................... 7
Fuse Replacement Guide ...................................................................................................................................... 7
Setup ..................................................................................................................................................................... 8
Unpack Materials .............................................................................................................................................. 8
Check Electrical Settings ................................................................................................................................... 8
LED Display Quick Set-up Guide ........................................................................................................................ 8
Required Tools: ............................................................................................................................................. 9
Parts Note: .................................................................................................................................................... 9
Frame Components (Not to Scale): ............................................................................................................... 9
Quadrants and Marquee Components (Not to Scale): ............................................................................... 11
Marquee Power Supply: ................................................................................................................................. 13
Network Cable Connections: Deluxe (P7) ....................................................................................................... 14
3 | Page
Page 4
Space Invaders Frenzy™
Network Cable Connections: Compact (P6) .................................................................................................... 15
Cabinet Assembly Setup Diagram ................................................................................................................... 16
Rear Cabinet Panel Covers: ............................................................................................................................. 17
Cabinet Assembly Instructions........................................................................................................................ 18
Startup Game .................................................................................................................................................. 18
Diagnostics and Adjustments .............................................................................................................................. 19
Basic Functional Test on Initial Power up ....................................................................................................... 19
Test Menus ..................................................................................................................................................... 20
Advertising Menu User Guide ......................................................................................................................... 26
Advertising Image Troubleshooting ................................................................................................................ 28
Keys to Maximizing Your Earning and Collections .......................................................................................... 29
PC Hardware ....................................................................................................................................................... 30
Fujitsu Mini BIOS ............................................................................................................................................. 30
Dell Inspiron 3050 BIOS .................................................................................................................................. 31
PC Hard Drive Recovery .................................................................................................................................. 32
Troubleshooting .................................................................................................................................................. 33
Technical Support ............................................................................................................................................... 39
Electrical and Mechanical Illustrations ............................................................................................................... 40
4 | Page
Page 5
Space Invaders Frenzy™
Safety
Operation
Before operating game, read this manual. Failure to properly install and operate this game could result in
malfunction or accident. Operate the game in accordance with the manual.
Transporting
The cabinet is very heavy. Because the monitor is high, the cabinet is also very top-heavy. Use appropriate
care when moving or transporting cabinet. It contains fragile glass and electronic components. Avoid rough
handling.
Handling Components
Many components are extremely sensitive to handling, environmental and Electrostatic Discharge (ESD)
events—especially the computer. Do not handle it roughly. Before servicing, call your distributor and inquire
about the PC warranty. Use proper ESD procedures when servicing. Protect components from harmful
environmental conditions, such as extreme temperatures, excessive moisture or other damaging effects.
Disconnect power
Always turn the power off and unplug the unit before servicing or making adjustments unless otherwise
instructed. Installing or repairing components while power is on can damage the components and void the
warranty.
Grounding
Avoid electrical shock. Do not plug in AC power until you have inspected and properly grounded the unit.
Only plug into a grounded, three-wire outlet. Do not use a “cheater” plug or cut off the ground pin on the line
cord.
Electrical Shocks
There is no isolation transformer in the cabinet. Disconnect AC power before servicing. However, be aware
that lethal voltages can remain in the electronic components even when AC power is disconnected. Use
extreme caution when servicing. Verify that there is a working ground connection. If the unit sustains water
damage, cease using it immediately and unplug AC power.
Power Cord
If the power cord is damaged or lost, replace it with an identical cord as supplied by the manufacturer or an
authorized service agent.
Surge Suppressor
It is recommended that you plug your game’s power cord into a surge suppressor to help protect from power
surges that may damage sensitive electronic components.
Water and Other Liquid Sources
Do not install game near sprinkler or other water jet sources. Do not use water jet to clean game. Keep
minimum clearance behind game and wall for proper ventilation but also prevent access of liquid from spills
and sprays from entering ventilation holes.
5 | Page
Page 6
Space Invaders Frenzy™
Connectors
When servicing machine, ensure all connectors mate properly. If connectors do not slip in easily, do not force
them. Connectors are often keyed and only connect one way. Check for correct orientation.
Computer
The computer contains sensitive components, including a hard drive. Do not handle it roughly. Call your
distributor before servicing its internal components. Ask about warranty information as it relates to the PC.
Do not turn the PC power switch on or off. It should remain permanently in the ON position.
Cycle AC power on or off with the cabinet power switch.
A dongle has been inserted into one of the USB ports. This is required for game play.
Do not remove the dongle except for troubleshooting purposes.
Hazard to Epileptics
A small portion of the population has an epileptic condition that may cause seizures. Affected persons
experience seizure while watching some television pictures or playing certain video games. People who have
not had seizures may still have an undetected epileptic condition. If anyone in your family has experienced
epilepsy symptoms (seizures or loss of awareness), consult your physical before using video games. While
children play video games, a parent should observe. Be alert to the following symptoms: dizziness, altered
vision, eye or muscle twitching, involuntary movements, loss of awareness, disorientation or convulsions. If
you or your child experiences these symptoms, discontinue use immediately and consult your physician.
Manual
Keep this manual available and ready for use. If the game fails to function properly, turn off the machine and
unplug the AC line cord. Contact your local distributor. You may not reproduce this document or any of its
contents without written authorization from Raw Thrills, Inc. or Play Mechanix™ Inc.
Specifications
For reasons such as performance, this product’s specifications may change without notice. Federal patent,
copyright and other intellectual property laws protect the content, devices and design of the game and its
equipment.
6 | Page
Page 7
Space Invaders Frenzy™
Product Specifications
Electrical Power
United States, international and Japan
Operating AC Current: 5/2.5 Amps
Voltage: 115/230 ~ VAC 50/60Hz
Inrush AC Current: 5 Amps
Temperature
50° F to 104° F
(10° C to 40° C)
Humidity
Must not exceed 95% relative humidity
Dimensions
Seat Cabinet
Height: 55.0” (1.40 meters)
Width: 43.5” (1.10 meters)
Depth: 32.5” (0.83 meters)
Main Cabinet
Height: 46.0” (1.17 meters)
Width: 43.5” (1.10 meters)
Depth: 29.0” (0.74 meters)
Display: Deluxe (P7)
Height: 117.0” (2.97 meters)
Width: 68.0” (1.73 meters)
Depth: 35.5” (0.90 meters)
Display: Compact (P6)
Height: 117.0” (2.97 meters)
Width: 68.0” (1.73 meters)
Depth: 35.5” (0.90 meters)
Fuse Replacement Guide
NOTE: FOR CONTINUED PROTECTION AGAINST
FIRE AND ELECTRICAL DAMAGE, USE ONLY
SPECIFIED FUSE TYPE AND VALUE.
RIO:
5VDC = 3A 250V SLO-BLO
12VDC = 5A 250V SLO-BLO
Game Lighting:
5A 250V SLO-BLO (x4)
LED Display Panel:
5A 250V SLO-BLO (x9 PER QUADRANT)
7 | Page
Page 8
Space Invaders Frenzy™
Setup
Unpack Materials
1. Place the shipping crates on a flat, stable surface.
2. Cut the banding straps and remove the cardboard lids.
3. Lift off the large cardboard containers surrounding the front pedestal and monitor assemblies and
remove any shipping cleats.
4. Remove the coin door key from the coin return slot.
5. Open the top coin door.
6. Locate the keys for the back door and the cash box door.
7. Open the cash box door and remove the cash box.
8. Check for shipping damage to the following:
• Marquee and monitor
• Cabinet decals
9. Check the AC line cord for visible signs of damage.
Pay particular attention to the plug and line cord insulation.
Check Electrical Settings
1. Verify the voltage in the nearest AC outlet.
2. Verify the AC outlet ground connection is present and working.
3. Open the service door of the main cabinet assembly
4. Locate the 24V power supply and verify the voltage selector switch is set to the correct AC voltage.
Please note: some 24V power supplies are universal and do not have a voltage selector switch.
LED Display Quick Set-up Guide
Important Note: This manual is accompanied by a separate document: “P7.62 LED Wall Assembly and Service
Document”. Please refer to this document when installing, servicing and troubleshooting the LED display. It
is a more comprehensive guide and provides more detail than the quick setup guide listed below. Keep this
and other documentation for future reference. Additional information regarding the latest version of
software and documents can also be found on our website:
www.rawthrills.com
8 | Page
Page 9
Space Invaders Frenzy™
1 – Left Base Assembly (x1)
2 – Right Base Assembly (x1)
3 – Left Upper Tube Assembly (x1)
4 – Right Upper Tube Assembly (x1)
(x24)
Listed below is a step by step process to assemble the LED Display for Space Invaders Frenzy. For
additional assistance, reference the full Assembly and Service Procedure included with the game. 2 people
are required to do the assembly. Ladders are recommended when assembling the top quadrants of the
LED screen. Refer to the “LED Wall Assembly and Service Document” for details.
Required Tools:
M6 Allen Key, #2 Phillips Screwdriver, and a Level
Parts Note:
All parts are labeled with decals. Refer to these decals when assembling the screen.
Frame Components (Not to Scale):
5 – Cross Tube (x4)
6 – M8x16mm Socket Head Cap Screw
9 | Page
Page 10
Space Invaders Frenzy™
10 | Page
Page 11
Space Invaders Frenzy™
7: Marquee Assembly (x1)
8: Marquee Power Supply (x1)
9: 4x9 Display Quadrant (x2)
10: 3x9 Display Quadrant (x2)
11: Center Planar Bracket (x1)
12: Side Planar Bracket (x4)
13: M5x8mm Phillips Head Screws (x8)
14: M8x16mm Socket Head Cap Screw (x16)
VIEW FROM BA CK
Quadrants and Marquee Components (Not to Scale):
11 | Page
Page 12
Space Invaders Frenzy™
(Note- Install screen quadrants individually)
12 | Page
Page 13
Space Invaders Frenzy™
Marquee Power Supply:
13 | Page
Page 14
Space Invaders Frenzy™
Network Cable Connections: Deluxe (P7)
14 | Page
Page 15
Space Invaders Frenzy™
1 23
4
NETWORK CABLE
FROM PEDESTAL
Network Cable Connections: Compact (P6)
15 | Page
Page 16
Space Invaders Frenzy™
Cabinet Assembly Setup Diagram
(Recommended minimum 100” distance from back of the LED base legs to the back of the seats)
16 | Page
Page 17
Space Invaders Frenzy™
Rear Cabinet Panel Covers:
Compact (P6) Version Only
1. Find and locate the magnetic panels shown on the right side of the diagram below.
Apply the magnetic panels one at a time in the way they are shown in the diagram below. These
2.
panels do not require any mounting hardware. The magnets will stick to the back of the cabinet
metal.
Make sure the cooling fans are unobstructed by the panels. The circle cutouts of the panels
3.
should line up with the cooling fan.
4.
Check to make sure the wires are dressed through the notches, so the panel is sitting flush
against the cabinet.
17 | Page
Page 18
Space Invaders Frenzy™
Cabinet Assembly Instructions
1. Place control (gun) cabinet in front of LED display.
2. Locate the two connecting brackets and the following hardware: (6) black tamper proof Torx
machine screws, ¼-20 thread, 1-1/2” long, and (6) ¼” black split lock washers, and (6) ¼” black
flat washers. Using a T-27 bit, attach these connecting brackets to the inside of each cabinet
side as shown in the cabinet assembly setup diagram.
3. Move pedestal assembly in front of control (gun) cabinet and connect harness. Locate the
following hardware: (6) black tamper proof Torx machine screws, ¼-20 thread, 1-1/2” long, and
(6) ¼” black split lock washers, and (6) ¼” black flat washers. Push cabinet halves (seat and gun
section) completely together and be sure not to pinch wire harness. Using T-27 bit, connect the
two cabinet halves with the hardware as shown in the cabinet assembly setup diagram.
4. Locate the following hardware: (2) black tamper proof Torx machine screws, ¼-20 thread, 2”
long, and (2) ¼” black split lock washers, and (2) ¼” black flat washers. Install screws through
pedestal floor to center connecting bracket.
5. Move the completed cabinet assembly into the desired position in front of the display. Raw
Thrills recommends a minimum distance of 100 inches total depth from back of LED wall base
legs to the back of the seats.
6. Connect the network CAT 5 cable between the back of the completed cabinet at the terminal
near the on/off switch and the back of the LED wall assembly. Use supplied D-channel sleeve
and carpet tape to properly dress the network cable on the floor.
7. Attach Marque Power Supply to frame and plug in the connector from marquee to marquee
power supply.
Startup Game
1. Plug in line cord to AC outlet.
2. Turn the power switch to ON.
3. Verify game display, sound, lights and controls are operating normally.
If not, turn off AC power and disconnect line cord. Refer to the diagnostic section of this manual.
18 | Page
Page 19
Space Invaders Frenzy™
TEST
SERVICE
Volume
UP
Volume
Diagnostics and Adjustments
The Service Button Panel has four buttons, three of which can navigate the menu system.
The start buttons and gun buttons can also advance through test menu screens.
DOWN
Navigating the Test Menu
Button Action
TEST/BACK (Not in Test Menu) Enters Test Menu
TEST/BACK (In Test Menu) Selects Highlighted Option
SERVICE (On Main Menu) Exits Test Menu
SERVICE (Not on Main Menu) Cancels Selection
VOLUME UP Move Up
VOLUME DOWN Move Down
Start Buttons Selects Highlighted Option
An on-screen message acknowledges changes or when you exit a selection without making a change.
Basic Functional Test on Initial Power up
See the Diagnostic Section for further information.
1. Enter the Switch Test menu and verify all switches function.
2. Enter the Sound Test menu and verify the audio works and is not distorted.
3. Enter the Coin Meter Test menu and verify the operation of the coin meter.
4. Enter the Cabinet Lamps Test menu and verify that all cabinet lights work correctly.
5. Enter the Watchdog Test menu, which reboots the game.
6. Upon a successful reboot, you are ready to adjust pricing, volume and other functions found in the
Adjustments, Audits, and Diagnostics section.
19 | Page
Page 20
Space Invaders Frenzy™
MAIN MENU
DIAGNOSTICS
PRICING ADJUSTMENTS
PAYOUT SETTINGS
AUDITS
UTILITIES
VOLUME
ADVERTISING
EXIT
DIAGNOSTICS
CRC CHECK
SWITCH TEST
CABINET LIGHTS TEST
LIGHT PATTERN CALIBRATION
GUN LIGHTS TEST
SOND TEST
COIN METER TEST
TICKET TEST
CALIBRATE GUNS
SOLENOID TEST
WATCHDOG TEST
EXIT
Test Menus
Main Menu
Choose from all available operator settings and menus here. You can use the test menu bracket and volume
buttons to navigate. The guns, gun triggers, and start buttons also are available to use for easier navigation
through these menus.
Diagnostics
This menu allows all game functions to be verified or diagnosed. You can improve collections by periodically
verifying proper game function and operation. This includes periodic CRC checks to verify that software has
not been corrupted or reporting an error.
• CRC Check: Checks for errors in the game’s files
• Switch Test: Test all the switches on the game
• Cabinet Lights Test: Test all cabinet lighting
• Light Pattern Calibration: Calibrate the LED-T
Molding on the cabinet
• Gun Lights Test: Test gun lighting
• Coin Meter Test: Tests functionality of “hard
meter”
• Ticket Test: Tests functionality of ticket mech(s)
• Calibrate Guns: Calibrate the aim of the guns
• Solenoid Test: Tests the functionality of the P1
and P2 guns
• Watchdog Test: Tests functionality of watch dog
(if working properly, game will reboot).
20 | Page
Page 21
Space Invaders Frenzy™
PRICING ADJUSTMENT
(COINS)
FREE PLAY
CURRENCY TYPE
CURRENCY INPUT
COIN VALUE
COINS TO PLAY
EXIT
PRICING ADJUSTMENT
(SWIPES)
FREE PLAY
CURRENCY TYPE
CURRENCY INPUT
SWIPE VALUE
SWIPESS TO PLAY
EXIT
Pricing Adjustments
This allows customization of coin values, currency denominations, bill pulse, and swipe value.
Pricing Adjustments: Coins Active (Default)
• Free Play: No coins or swipes needed to play
• Currency Type: Choose between: Cash,
Tokens, or Card Swipes
• Coin Value: Money value of a coin. This is a
very important setting and impacts payout.
Default value is $0.25
• Coins To Play: Number of coins per credit
Pricing Adjustments: Swipes Active
• Free Play: No coins or swipes needed to play
• Currency Type: Choose between: Cash,
Tokens, or Card Swipes
• Swipe Value: Money value of a coin. This is a
very important setting and impacts payout.
Default value is $0.25
• Swipes To Play: Number of coins per credit
21 | Page
Page 22
Space Invaders Frenzy™
PAYOUT SETTINGS
PAYOUT PERCENT
TICKET VALUE
JACKPOT
TWO POINT TICKETS
EXPRESS PAYOUT
E-TICKET MODE
TICKETLESS MODE
JAPAN MODE
EXTRA LIVES (Available in Amusement
Only)
EXIT
Payout Settings
This menu allows for customization of target compensation, payout percentage, ticket value, E-Ticket support
(Paperless Tickets), and Jackpot compensation.
• Payout Percent: Set your targeted payout percentage. Game defaults to 40% which is the recommended
setting. IMPORTANT NOTE- Space Invaders Frenzy has a dynamic targeted payout system in place but it is
a skill based redemption game. There will be some slight volatility and variation in payout among
different skill level players.
• Ticket Value: Set the value of your tickets. Default value: $0.01 and is the recommended setting.
• Jackpot: Set the value of the game’s jackpot award up to 1000 tickets. Default value is 500.
• Two Point Tickets: When set to ON, this setting allows a single ticket dispensed to be worth 2 points in
the game.
• Express Payout: when set to ON, allows for tickets to be dispensed as tickets are earned (recommended
setting). When set to OFF, ticket payout is dispensed after the completion of the current game.
• E Ticket Mode: Raw Thrills supports the use of paperless tickets or “E-TICKETS” with our new “ETicket
Mode”. If you are using digital tickets via a card based system like Embed, Intercard, Semnox or
equivalent system, you will need to activate E-Ticket Mode. This mode provides E-Ticket support to a 2player simultaneous play experience like Space Invaders Frenzy. It splits the credits and Eticket payout to
the Player 1 and Player 2 sides of the game to two separate card swipers. Each player’s payout and
credits will be properly divided to the corresponding player’s card.
• Ticketless Mode: This mode is a unique action arcade experience and is different than the video
redemption mode. While the controls and general gameplay remain the same, "Ticketless Mode" has
many various waves, power ups, bonus stages, and a continue feature with gameplay tailored towards a
longer playing experience. The player plays only for points and to complete the game after all 100 stages
are cleared. There are no tickets awarded during this mode. To turn on “Ticketless Mode”, you can
access it in the Payout Settings menu. This mode is perfect for non-ticket redemption locations and
provides a more traditional longer play action arcade experience.
22 | Page
Page 23
Space Invaders Frenzy™
AUDITS
SYSTEM AUDITS 1
SYSTEM AUDITS 2
SYSTEM AUDITS 3
COIN AUDITS
GAME AUDITS
GAME AUDITS 2
PAYOUT AUDITS
EXIT
(Payout Settings Continued)
Japan Mode: This mode is a unique action arcade experience and is different than the video redemption
•
mode. While the controls and general gameplay remain the same, "Japan Mode" has many various
waves, power ups, bonus stages, and a continue feature with gameplay tailored towards a longer playing
experience. Additionally, this mode sets the pricing to “Yen” for the Japanese market. The player plays
only for points and to complete the game after all 100 stages are cleared. There are no tickets awarded
during this mode. To turn on “Japan Mode”, you can access it in the Payout Settings menu. This mode is
perfect for non-ticket redemption locations and provides a more traditional longer play action arcade
experience.
• Extra Lives: This is an adjustment only available and accessible when Amusement Only is set to ON.
Operator can adjust the number of lives given per credit.
Audits
Audit screens help assess game performance, find intermittent problems, decide whether to adjust game
difficulty and free game award and help maximize game earnings.
• System Audits: Logged information including boots, resets, game times, and more
• Coin Audits: Tracks income related information, coin slot usage, dollar bill usage, and more
• Game Audits: Tracks the gameplay habits of your customers. Average scores, bonuses, and more.
• Game Audits 2: Tracks the gameplay habits of your customers. How many bonus ships hit, how many
bombs used per game, and more.
• Payout Audits: Tracks the gameplay habits of your customers. Number of jackpots won, payout
percentage, and high scores, ad more.
23 | Page
Page 24
Space Invaders Frenzy™
UTILITIES
RESETS
COPY TO USB
LEADERBOARD SETTINGS
SCREEN BRIGHTNESS
TRADESHOW MODE
ATTRACT MUSIC MODE
EXIT
VOLUME
GAME VOLUME 13/20
ATTRACT VOLUME 7/20
CREDIT VOLUME 17/20
MINIMUM VOLUME 4/20
EXIT
Utilities
Utilities is a miscellaneous menu of operator tools and settings
• Resets: All operator resets are available in this menu. Coins, tickets, audits, adjustments, high score
leaderboards, are all accessible here. You can also factory reset the game from this menu which will
restore all settings in the game to their original factory settings.
• Copy to USB: Allows you to upload your audits to an easy to read text file (.TXT) on a USB flash drive
• Leaderboard Settings: Allows you to turn high score leaderboards on and off. ON is the default and
recommended setting.
• Screen Brightness: Adjust the brightness of your Space Invaders Frenzy screen. There are 6 levels of
brightness to choose from. 6 is the default value and is the recommended setting.
• Tradeshow Mode: Turn this mode on when operating on a trade show, sales floor, or demo floor.
The game runs on free play and also simulates ticket payouts without a ticket error appearing on the
screen.
• Attract Music Mode: This allows you to set how frequently you want the volume to play during the
attract mode. Choose from “ON”, “Occasionally”, and “OFF”.
Volume
• Game Volume: Adjusts the volume level during gameplay
• Attract Volume: Adjusts the volume during the attract mode sequences
• Credit Volume: Adjusts the volume level of the credit chime only (Independent setting of game and
attract volume)
• Minimum Volume: Adjusts the minimum floor the volume can be lowered
24 | Page
Page 25
Space Invaders Frenzy™
ADVERTISING
AD SLOT 1
AD SLOT 2
AD SLOT 3
AD SLOT 4
AD LENGTH 10SEC
EXIT
Desired Resolution: 224 x 288
Formats: TGA, PNG, JPG, GIPH
Advertising
Space Invaders Frenzy has an advertising feature that allows the operator to upload photos which will be
displayed during the attract mode of the game.
• Ad Slot 1: First of 4 available advertising file slots
• Ad Slot 2: Second of 4 available advertising file slots
• Ad Slot 3: Third of 4 available advertising file slots
• Ad Slot 4: Fourth of 4 available advertising file slots
• Ad Length: Adjusts the time duration that the advertising image appears
25 | Page
Page 26
Space Invaders Frenzy™
Advertising Menu User Guide
1. Identify and select advertising image files you would like to have displayed on the screen during the
game’s attract mode. On your personal computer or laptop, upload these advertising images to a
USB flash drive. Image files should be .TGA, .PNG, .JPG, or GIPH format type.
Note: The resolution of images should be 224 x 288 pixels. (224 x 288)
Larger resolution files or different file types can cause an error or won’t
appear correctly on your Space Invaders Frenzy screen. (To be able to
clearly read text and images, we recommend making your image 72 DPI,
224 x 288 resolution) Game can hold up to 5 images.
2. After you have your images picked out, sized, and copied to your USB flash drive, you are now ready
to upload the images into Space Invaders Frenzy. Open the coin door and find the service bracket
that has the test menu and service buttons. On this bracket, you will find a USB slot to insert your
flash drive. ***Important*** Make sure to only insert your flash drive while the game is in attract
mode. Never insert a flash drive while the game is booting up, or in the Test Menu.
(Above: Image of the USB slot above the test menu buttons)
26 | Page
Page 27
Space Invaders Frenzy™
ADVERTISING
AD SLOT 1
AD SLOT 2
AD SLOT 3
AD SLOT 4
AD LENGTH 10SEC
EXIT
Desired Resolution: 224 x 288
Formats: TGA, PNG, JPG, GIPH
AD SLOT
LOAD IMAGE
AD BRIGHTNESS
PREVIEW IMAGE
CLEAR IMAGE
EXIT
SELECT A FILE TO LOAD
(Your Flash Drive Files Listed Here)
3. Once your USB flash drive is inserted into the USB slot on the service control panel, you can then
press the “TEST” button to access the main menu.
4. Select “ADVERTISING” from the main menu to access the upload feature. From this menu, you can
then select an ad slot for your image.
5. After you are in the “AD SLOT MENU” you can select “LOAD IMAGE” which generates a list of the file
names of the image files that are on your USB drive. Navigate to the file name you would like to
upload and select it. (See image below)
6. When you select the image you would like to upload, you will be presented with a preview of the
image, which you can accept or decline. If you accept the image, you will be taken back to “AD SLOT
MENU” which will allow you to load a different image, adjust the ad brightness, preview the image
again, clear your image or exit the menu.
Please Note: If you have lighter colors or lots of white areas in your advertisement, we recommend that you
adjust the ad brightness to a lower level. The default ad brightness is 6 but many advertisements have a
better appearance at 3-5 brightness.
27 | Page
Page 28
Space Invaders Frenzy™
Error
Solution
Check your USB drive to ensure it is properly
did not become disconnected or dislodged.
Please check the resolution of the image that you
224 x 288 pixels
Check to make sure your files have properly loaded
the proper .PNG, .TGA, or .JPG format.
FILES MISSING FROM AD SELECT SCREEN
HAS MORE THAN 1 PAGE
Please remove some files on your flash drive and
files on the main USB flash drive folder
Advertising Image Troubleshooting
USB DEVICE NOT CONNECTED
connected. Also, check to make sure your USB drive
can be read on other devices. Ensure the coin door
USB connection cable to the PC inside the cabinet
INCORRECT RESOLUTION DETECTED
NO IMAGES ON FLASH DRIVE
IN AD SELECT SCREEN
WHEN THE AD SELECT SCREEN
are trying to upload. Recommended image size is
on to your flash drive and ensure that they are in
check to make sure you do not have more than 10
28 | Page
Page 29
Space Invaders Frenzy™
Keys to Maximizing Your Earning and Collections
Card Swipe Locations
• Make Sure Your Game is Set to Swipes Mode:
1. Hold the Test Button for 2 seconds to enter the Test Menu.
2. Select “Pricing Adjustments” from the menu.
3. Select “Currency Input” from the menu.
4. Select “Swipes” from the menu.
5. Set “Swipe Value” to the currency equivalent of your swipe, or the payout will be incorrect. THIS
SETTING IS EXTREMELY IMPORTANT! (Example: If the card swipe is worth $1.50 in your card
system, set the swipe value to $1.50 as well)
E-Ticket Locations
• Make Sure Your Game is Set to E-Ticket Mode:
1. Hold the Test Button for 2 seconds to enter the Test Menu.
2. Select “Payout Settings” from the menu.
3. Select “E Ticket Mode” and set to “On”
IMPORTANT NOTE: You must have two card swipers for E-Ticket mode to work. One for Player 1 Gun
and one for Player 2 Gun.
Coin Locations
• Make Sure Your Pricing & Coin Value are Correct:
1. Hold the Test Button for 2 seconds to enter the Test Menu.
2. Select “Pricing Adjustments” from the menu.
3. Select “Coins to Play” and set the desired amount of coins per game of Space Invaders Frenzy™.
4. After setting the coins per play, set “Coin Value” to the currency equivalent of your coin, or the
payout will be incorrect. THIS SETTING IS EXTREMELY IMPORTANT! (Example: If your coin is
worth $0.25, set “Coin Value” to $0.25 as well)
2 Point Ticket Locations
• Make Sure the 2 Point Ticket Setting is Activated:
1. Hold the Test Button for 2 seconds to enter the Test Menu.
2. Select “Payout Settings” from the menu.
3. Select “Two Point Tickets” and set to “On”. (Your tickets are now worth 2Pts each)
IMPORTANT NOTE: Only use this setting if your tickets are worth 2 points per ticket or the payout
will be incorrect.
More Tickets = More Fun = Better Earnings
• We recommend using the default payout setting of 40% to maximize earning potential and fun factor
for the players. To set the “Payout Percentage”:
1. Hold the Test Button for 2 seconds to enter the Test Menu.
2. Select “Payout Adjustments” from the menu.
3. Select “Payout Percent” and adjust to desired amount.
IMPORTANT NOTE: Space Invaders Frenzy™ will dynamically adjust to your desired payout setting.
29 | Page
Page 30
Space Invaders Frenzy™
(Above: Dell Inspiron 3050) (Above: Fujitsu Mini PC)
PC Hardware
Your Space Invaders Frenzy game may ship with either a DELL INSPIRON 3050 computer or a Fujitsu
IMP-3313-S4-4G-HD Mini PC computer ("Fujitsu Mini PC"). The Dell Inspiron 3050 computer is square in
shape has a “Dell” logo on it while the Fujitsu computer is rectangular in shape and has no logo. Listed
below are the BIOS settings for each computer.
NOTICE
Both the DELL INSPIRON 3050 and FUJITSU MINI PC ship with correct BIOS settings. Making changes to the
BIOS different from the description below may adversely affect game functions.
Fujitsu Mini BIOS
To Access BIOS Settings:
With the computer powered off, plug a USB keyboard into an open USB slot. Hold the ‘F2’ key and turn the
computer on. Continue holding the F2 key until the BIOS Setup screen appears.
Note: All settings not listed should remain their default values.
Advanced
+ Graphics Configuration
- Internal Graphics ..................................... [Enabled]
- Primary Display ............................................... [IGD]
- IGD MEMORY ............................................... [512M]
Power
- Power Failure Recover ...................................... [Always ON]
Boot
- Prefer USB Boot ........................................................[Enable]
Note: After exiting BIOS settings screen, power cycle the cabinet by using the cabinet’s main power switch.
30 | Page
Page 31
Space Invaders Frenzy™
Dell Inspiron 3050 BIOS
To Access BIOS Settings:
With the computer powered off, plug a USB keyboard into an open USB slot, hold ‘F12’ key and turn the
computer on. Continue holding the F12 key until a menu with a blue background appears. From the e menu,
select ‘BIOS Setup’
Power
- Nothing
Power
- Intel (R) SpeedStep ™ ............................................ [Enabled]
- Virtualization ......................................................... [Enabled]
- Integrated NIC ....................................................... [Enabled]
- SATA Operation ...........................................................[AHCI]
- Adapter Warnings ................................................. [Enabled]
+ Graphics Configuration
- Nothing
+ Power Options
- Wake Up by Integrated LAN .................... [Disabled]
- AC Recovery .......................................... [Power ON]
- Auto Power On ........................................ [Disabled]
Security
- Nothing
Boot
- Boot List Option .......................................................[Legacy]
- File Brower Add Boot Option
- File Brower Del Boot Option
- Secure Boot ........................................................... [Disabled]
- Load Legacy Option Rom ....................................... [Enabled]
st
Boot Priority ................................... [USB Storage Device]
- 1
Exit
- Nothing
Note: After exiting BIOS settings screen, power-cycle the cabinet by using the cabinets main power switch.
31 | Page
Page 32
Space Invaders Frenzy™
WARNING!
CRC File Missing! Reinstall Software!
File Damaged! Reinstall Software!
File Missing! Reinstall Software!
PC Hard Drive Recovery
Symptoms requiring PC hard drive recovery include
• File Test reports bad or missing files.
• Game fails to finish loading during startup.
• After resetting the AC power, an error is reported.
• Erratic Game or Attract Mode.
• The following screen:
The only way to repair corrupt files is to reinstall the software as described below:
COMPUTER
The computer contains sensitive components. Do not handle roughly. Call your distributor before servicing its
internal components. Ask about warranty information as it relates to the PC.
Do not use the PC on/off switch. Turn AC power on or off with the cabinet power switch.
Steps to Re-install the software:
(NO DVD Restoration. USB Thumb Drive is used on the Dell Inspiron3050 PC or Fujitsu Mini)
1. With game and PC on, verify that the RIO board has power. If not, see Troubleshooting.
2. Open the coin door
3. Insert the recovery USB thumb drive (included in your game) into the USB port on the Test button
bracket inside the coin door.
4. Turn cabinet power switch to OFF. Wait 30 seconds.
5. Turn cabinet power switch to ON.
6. Select the Space Invaders Frenzy restore version from the menu and follow on screen instructions
7. If recovery does not begin, check to ensure USB Drive is inserted correctly and is not damaged.
8. Initial software loading may take several minutes. Check progress periodically.
Do not interrupt power or reset the game during recovery.
9. When software has been loaded, a message indicates that restore is complete. When instructed to
remove USB Drive, wait 15 seconds to remove the drive from the PC.
10. Turn cabinet power switch off and then turn the cabinet on again. Your game will now be restored.
32 | Page
Page 33
Space Invaders Frenzy™
Problem
Possible Cause
Solution
Game not plugged in.
Plug game into AC outlet.
Game not turned on.
Turn on main power switch.
Check and replace fuse. See
Test AC outlet and plug game
into powered outlet.
PC BIOS set incorrectly.
See BIOS Settings section.
Flash Drive Installer is left
Disconnect Flash Drive Installer
Advertising USB flash drive left
Remove USB flash drive and
Replace the micro switch on the
switch.
Disconnect the cabinet from AC
Ensure all connections to PCB
are secure. Replace PCB if faulty.
Troubleshooting
Warning: Review safety chapter before making any adjustments to game.
Game will not power up.
Buttons do not work.
Game fuse is blown.
No power to receptacle.
connected to PC.
connected to PC.
Faulty micro switch.
Faulty wiring.
Specification section for fuse
values.
and power cycle the game.
power cycle the game
button and re-test. Verify that
the wires are connected to the
correct spades on the micro
power. Verify that all wires are
firmly connected to each button
and the PCB. Verify that no
wires are frayed or improperly
shorting to ground. Verify that
wires are connected to the
correct spades on the micro
switches.
Faulty PCB.
33 | Page
Page 34
Space Invaders Frenzy™
Problem
Possible Cause
Solution
To test a USB port, turn off the
Bad connection.
Check connection to speakers.
Use VOL UP button on Test
Verify all wires are firmly
Remove the grill and inspect
each speaker for visible damage.
Run the Sound Test from System
A weak or low muffled sound is
To verify audio is working at the
computer audio port.
Check external DC supply and
Check all ground wires in
Neither buttons nor audio
work.
PCB connected to faulty USB
port (boot message may
indicate not detected)
game, disconnect the device
from the port, and then connect
the game dongle to the port.
Reboot the game. A No Dongle
message indicates the port is
bad. If the game starts, the port
is working. After the test,
reconnect all devices to the
correct USB ports and reboot.
No sound or bad sound.
Volume set too low.
Faulty wiring.
Blown speakers.
Reversed wires.
Faulty PCB.
panel to raise volume.
connected to the speakers, PCB,
and green computer audio port.
Verify that each wire is
connected to the correct port
and no wires are frayed or
improperly shorting to ground.
Tests in the Operator Menu to
verify each speaker is working.
a sign of reversed speaker wires.
Check for reversed wires on
each speaker.
computer, connect stereo
headphones to the green
Constant low audio hum.
Faulty power supply.
Open ground.
the PC supply.
cabinet. Ensure AC wall outlet is
properly grounded
34 | Page
Page 35
Space Invaders Frenzy™
Problem
Possible Cause
Solution
Game does not load.
PC Drive test reports “bad” or
“missing” files.
Game fails to finish loading.
After resetting, game still
reports an error.
Erratic game mode or attract
WARNING!
Mode and Run “File Test.”
Game Resets
Bad file.
Run Flash Installer.
Faulty meter.
Replace coin meter.
Replace 12vdc 5A fuse(s) on
PCB.
Check wiring from meter to PCB
board.
Dongle missing or disconnected.
Find dongle cable and reseat in
USB port.
Faulty USB port.
Insert dongle cable in different
USB port.
Incorrect setting in Pricing
Disconnect cabinet from AC
Verify coin mech is not jammed.
Exits Test Mode every 3
seconds.
Slide or toggle button off after
Test Menu appears
mode.
Data files Corrupted.
(Game Operation May Become
Unstable.)
Use “Test” Switch to Enter Test
Coin meter does not click
during test.
Dongle Not Present
PC hard drive failure.
Blown fuse(s) on PCB
No pulse to meter.
Recover hard drive.
See Flash Installer Document or
contact your distributor for the
latest software revision.
Improper number of credits
given when coins or bills are
inserted.
Adjustments.
Faulty wiring.
Faulty coin mech.
Test button stuck in ON position.
Adjust pricing settings.
power. Verify wires are firmly
connected to coin mech and bill
validator and ground wires are
properly connected. Verify no
wires are frayed or shorting to
ground.
Ensure coin mech is properly
aligned and latched to coin
door.
35 | Page
Page 36
Space Invaders Frenzy™
Problem
Possible Cause
Solution
Turn PC power switch on.
Check and secure DVI connector
connector to PC.
Connect network cable between
With the cabinet AC power off
(Port “U”) and the RJ45 Network
jack on the inside of the cabinet.
Faulty RJ45 pass-through
USB cable disconnected.
Check USB connection from PC to
RIO board.
No Power to RIO board.
Check for proper voltage (+5V,
+12V) at RIO P1 connector.
Dongle missing or disconnected.
Find dongle cable and reseat in
USB port.
Faulty USB port.
Insert dongle cable in different
USB port.
Defective LED module.
Tap gently on defective pixel.
Replace LED module.
Defective LED module.
Replace LED module.
No Video
PC not turned on.
Video cable not secure.
Network cable missing or not
secure between cabinet and LED
screen.
Network cable missing or not
secure between LED controller
card and RJ45 Network jack.
Ensure IEC cable tightly plugged
in. Trace cable back to source to
ensure continuity.
to LED controller card. Check
and secure DVI or HDMI
RJ45 Network jack on the back
of the cabinet and quadrant #1
of the LED screen. Power cycle
the game after connecting the
network cable.
and the line cord removed,
check the Ethernet cable
between the LED controller card
Connect RIO Board or RIO Board
Missing.
Dongle Not Present
Defective single pixel.
Several Defective pixels, but not
all in same row or column.
Network jack.
Replace jack.
36 | Page
Page 37
Problem
Possible Cause
Solution
Entire row or column of
Faulty data transmission.
Check ribbon cable between
malfunctioning module and
module to the left (from the
back).
Check/replace module to the left
(from the back).
If module is left-most in quadrant
(from the back):
Defective LED module.
Replace LED module.
Faulty data transmission.
Check ribbon cable between
malfunctioning module and
module to the left (from the
back).
Check/replace module to the left
(from
If module is left-most in quadrant
(from the back):
display controller.
Bad power.
Check power connection to LED
module.
Check quadrant fuse block for
blown
Defective LED module.
Replace LED module.
defective pixels.
Space Invaders Frenzy™
• Check ribbon cable
between module and
LED display controller.
• Check quadrant LED
display controller.
Entire module malfunctioning.
the back).
• Check ribbon cable
between module and
LED display controller.
• Check quadrant LED
fuse.
37 | Page
Page 38
Space Invaders Frenzy™
Problem
Possible Cause
Solution
Faulty data transmission.
Check ribbon cable between
malfunctioning module and
module to the left (from the
back).
Check/replace
(from the back).
If module is left-most in quadrant
(from the back):
Bad power.
Check power connection to LED
module.
Check
blown fuse.
Entire module malfunctioning.
module to the left
• Check ribbon cable
between module and
LED display controller.
• Check quadrant LED
display controller.
quadrant fuse block for
Screen Note 1: Space Invaders Frenzy uses over 65,000 LEDs on its giant screen. It is normal for a few LEDs to
fail over the course of operating the game. This will not affect normal operation or viewing of the game and
most will not be noticeable to the eye.
Screen Note 2: This manual is accompanied by a separate document: “LED Display (P7.62 Version) Full
Assembly and Service Procedure”. Please refer to this document when servicing and troubleshooting the LED
display. Additional information regarding the latest version of software and documents can also be found on
our website:
Screen Note 3: If the ethernet cable is plugged into the incorrect port, it can cause errors to occur. Make sure
that the USB cable is plugged in and the ethernet cable is plugged into the "U" port. See diagram below:
www.rawthrills.com
38 | Page
Page 39
Space Invaders Frenzy™
Technical Support
Contact your distributor for support.
For a list of authorized distributors near you, check the Raw Thrills website at:
www.rawthrills.com
39 | Page
Page 40
Space Invaders Frenzy™
Electrical and Mechanical Illustrations
NOTE: PLEASE CHECK FOR THE LATEST VERSION OF GAME SOFTWARE AND MANUAL AT
WWW.RAWTHRILLS.COM
40 | Page
Page 41
ITEM NO.
1
2
3
4
5
6
7
8
PART NUMBER
Space_Invaders_Control_Assy
600-01457-01
McMaster-Carr - 97416A119
McMaster-Carr - 93711A500
Special Order Hardware (not
available at McMaster-Carr)
Space_Invaders_Pedestal_Assy
McMaster-Carr - 96075A231
P7.62_LED_Wall_Assy
DESCRIPTION
Control Cabinet Assembly
JP55" Bracket Connect
Black-Oxide Steel SAE Flat Washer, 1/4" Screw
Size, 0.281" ID, 0.625" OD
Black-Oxide 18-8 Stainless Steel Split Lock
Washer for 1/4" Socket Head Screws, 0.26" ID,
0.363" OD
Alloy Steel Tamper-Resistant Torx Rounded
Head Screws, 1/4"-20 Thread Size, 2" Long
Pedestal Assembly
Alloy Steel Tamper-Resistant Torx Rounded
Head Screws, 1/4"-20 Thread Size, 1-1/2" Long
Complete LED Wall Assembly inc. 12" Extensions
(w/ P7.62 Panels & Marquee)
QTY.
1
2
8
14
14
12
1
2
1
NOT SHOWN:
> CABLES/HARNESSING
> CABLE MANAGEMENT WIRE CHANNEL
- 5' LONG W/ ADHESIVE TAPE
Space Invaders Frenzy Assembly
2
7
6
1
3
4
5
Page 42
16
13 1718
25 26 27 28
21
19
14
33
34
36
23
20
24
30
32 31 35
NOT SHOWN:
> HARDWARE
> 500-00131-01 - RGB LED Strip Reel
- 2X 120CM / 72 LEDs (installed in #10)
15
22
9
10 1211
29
Space Invaders Frenzy
Control Cabinet Assembly
(BOM on next page)
Page 43
Space Invaders Frenzy - Control Cabinet Assembly: BOM
ITEM NO.
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NUMBER
601-00779-01
603-00718-01 (47.5 in)
600-01939-01
600-01938-01
Space_Invaders-Ray_Gun_Assy
600-01913-01
600-01912-01
600-01936-01
600-01937-01
600-01486-01
702-00015-01
702-00019-01
600-01944-01
AC_Plate_Sub-Assy
800-00001-00
820-00012-00
Space_Invaders_RIO_Assy
DESCRIPTION
Main Cabinet
LED T-Molding Extrusion - 47.5"
Flanged LED T-Molding Clip
LED T-Molding Clip
Space Invaders Gun Assembly (w/ Ray Gun Tip Assembly)
Gun Gusset Bracket L
Gun Gusset Bracket R
Gun Plate Rear
Gun Plate Front
Dash Gun Cover Plate
Large Round RED Pushbutton (Suzo-Happ)
Large Round BLUE Pushbutton (Suzo-Happ)
Cabinet Seam Plate
AC Power Plate Assembly
120mm Wire Fan Guard
Cooling Fan (standard size): 12VDC, 3W, 80CFM
RIO Assembly w/ Mounting Plate
QTY.
1
2
2
2
2
1
1
2
2
2
1
1
1
1
2
1
1
26
27
28
29
30
31
32
33
34
35
36
500-00187-01
500-00193-01
800-00040-01
850-00024-01
380-00002-01
800-00043-01
800-00005-01
2-1-10-00-00-000
600-01464-01
600-01458-01
Space_Invaders_Back_Door_Assy
Switching Power Supply: 156W, 24V, 6.5A (Mean Well RS-150-24)
Switching Power Supply: 320.4W, 12V, 26.7A, PFC (Mean Well
RSP-320-12)
Solid State Relay (Magnecraft 6210DSX-1)
Fujitsu PC (IMP-3313-S4-4G-HD)
LED Control Card
Ticket Dispenser Door Assembly (Suzo-Happ)
Mid-Width Coin Door Assembly (Suzo-Happ)
5.25", 8 Ohm Full Range Speaker (Goldwood)
JP55" Speaker Grill
JP55" Center Bracket Connect
Back Door Sub-Assembly
1
1
1
1
1
2
1
2
2
1
1
Page 44
37 42
ITEM NO.
37
38
39
PART NUMBER
600-01754-01
703W-00/08
McMaster-Carr 90272A146
DESCRIPTION
AC Electronics Plate
AC Receptacle: 250V, 15A (Qualtek)
Steel Phillips Rounded Head Screws, 6-32
Thread Size, 3/8" Long
QTY.
1
1
2
41
ITEM NO.
43
44
45
40
PART NUMBER
600-01914-01
500-00040-01
McMaster-Carr 90316A192
39
40
41
42
38
DESCRIPTION
RIO Mounting Plate
RIO PCB
18-8 Stainless Steel Hex Washer
Head Slotted Machine Screw, 8-32
Thread, 3/8" Length
T9-611P-6
1832.3312
602690
Thermal Circuit Breaker: 240VAC, 6A,
Snap-in, Fuseholder, 1-Pole (Schurter)
Rocker Switch (DPST): 250VAC, 20A
(Marquardt)
Cat5e Keystone Coupler: Black,
RJ45F/RJ45F (CNAweb)
Space Invaders Frenzy
AC Power Plate Assembly
QTY.
1
1
10
43
44
1
1
1
46
47
48
500-00194-01
520-00024-01
McMaster-Carr 90272A106
5V, 5A Switching Regulator PCB
(12V input)
Aliens / Terminator Deluxe Gun
Kickboard
Steel Phillips Rounded Head
Screws, 4-40 Thread Size, 1/4" Long
1
4
16
Space Invaders Frenzy
RIO Assembly w/ Mounting Plate
45
46
47
48
Page 45
ITEM NO.
49
50
51
PART NUMBER
601-00780-01
600-00043-01
McMaster-Carr -
90054A196
DESCRIPTION
Back Door
Lock Retainer Plate
Flanged Hex Head Screws for Sheet Metal, Zinc-
Plated Steel, Number 8 Size, 5/8" Long
QTY.
1
1
3
49
53
54
52
53
54
55
56
150-00001-00
800-00001-00
McMaster-Carr -
90272A201
McMaster-Carr -
90126A009
McMaster-Carr -
90631A009
52
Standard Door Lock Assembly (for 3/4" Panels)
120mm Wire Fan Guard
Steel Phillips Rounded Head Screws, 8-32 Thread
Size, 1-1/4" Long
Zinc-Plated Steel SAE Washer for Number 8 Screw
Size, 0.188" ID, 0.438" OD
Low-Strength Steel Nylon-Insert Locknut, Zinc-
Plated, 8-32 Thread Size
1
2
8
8
8
55
56
51
50
Space Invaders Frenzy
Back Door Sub-Assembly
Page 46
57
62
59
60
61
58
63
68
64
65
67
71
70
66
72
ITEM NO.
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
PART NUMBER
601-00781-01
600-01915-01
McMaster-Carr -
97416A119
McMaster-Carr 93711A500
McMaster-Carr 96075A231
Space_Invaders_Seat_
Assy
McMaster-Carr 96765A145
McMaster-Carr 93711A600
McMaster-Carr 92965A581
McMaster-Carr 92141A030
McMaster-Carr 91102A030
McMaster-Carr 92865A587
Space_Invaders_Rear
_Seat_LED_Cap_Assy
601-00783-01
McMaster-Carr 97416A113
McMaster-Carr 95638A201
DESCRIPTION
Seat Cabinet
Seat Mount Bracket
Black-Oxide Steel SAE Flat Washer,
1/4" Screw Size, 0.281" ID, 0.625" OD
Black-Oxide 18-8 Stainless Steel Split
Lock Washer for 1/4" Socket Head
Screws, 0.26" ID, 0.363" OD
Alloy Steel Tamper-Resistant Torx
Rounded Head Screws, 1/4"-20 Thread
Size, 1-1/2" Long
Seat Assembly
Black-Oxide 18-8 Stainless Steel
Washer for 5/16" Screw Size, 0.344" ID,
0.75" OD
Black-Oxide 18-8 Stainless Steel Split
Lock Washer for 5/16" Socket Head
Screws, 0.322" ID, 0.457" OD
Black-Oxide Grade 5 Steel Hex Head
Screws, Medium-Strength, 5/16"-18
Thread Size, 3/4" Long
18-8 Stainless Steel Washer for 5/16"
Screw Size, 0.344" ID, 0.75" OD
Zinc-Plated Steel Split Lock Washer for
5/16" Screw Size, 0.322" ID, 0.583" OD
Medium-Strength Grade 5 Steel Hex
Head Screw, Zinc-Plated, 5/16"-18
Thread Size, 1-1/2" Long, Fully
Threaded
Rear Seat LED Cap Assembly
Seat Access Panel
Black-Oxide Steel SAE Flat Washer,
Number 8 Screw Size, 0.188" ID, 0.438"
OD
Tamper-Resistant Torx Rounded Head
Screws for Sheet Metal, 18-8 Stainless
Steel, Number 8 Size, 1-1/4" Long,
PAINT BLACK
QTY.
1
1
10
10
10
2
4
4
4
12
12
12
1
2
8
8
69
Space Invaders Frenzy
Pedestal Assembly
Page 47
82
77
73
74
76
75
ITEM NO.
73
74
75
76
77
78
79
80
81
82
83
84
85
86
PART NUMBER
603-00523-01
600-00105-01
600-00620-01
McMaster-Carr 95638A197
Seatback LED Assy
807-00003-00
McMaster-Carr -
90054A196
Woofer LED Assy
600-00106-01
606-01261-01
600-01840-01
McMaster-Carr 97416A113
500-00065-01
603-00540-01
DESCRIPTION
Plastic Seat - Red
Seat Headrest Speaker Grill
Middle Seat Plate
Tamper-Resistant Torx Rounded Head Screws for
Sheet Metal, 18-8 Stainless Steel, Number 8 Size,
3/4" Long, PAINT BLACK
White LEDs w/ Foam (500-00093-01 - 35CM / 21
LEDs) & Plastic LED Extrusion (603-00762-01 - 16")
6.5" Woofer, 8 Ohm (Goldwood)
Flanged Hex Head Screws for Sheet Metal, Zinc-
Plated Steel, Number 8 Size, 5/8" Long
ROB Side Emitting LEDs (500-00219-01 - 70CM / 63
LEDs) & Plastic LED Extrusion (603-00762-01 - 28")
Woofer Grill
Seatback Translite
Seatback Clear Overlay
Black-Oxide Steel SAE Flat Washer, Number 8
Screw Size, 0.188" ID, 0.438" OD
Red LED Puck Light w/ Black Face PCB
LED Spotlight Lens - Red Tint
QTY.
1
2
1
24
2
1
4
1
1
1
1
6
2
2
84
83
85
86
78
79
8081
Space Invaders Frenzy
Seat Assembly
Page 48
93
ITEM NO.
87
88
PART NUMBER
601-00782-01
603-00718-01 (20.5 in)
DESCRIPTION
LED Cap Panel
LED-T-Molding Extrusion - 20.5"
QTY.
1
2
94
88
89
91
NOT SHOWN:
> 500-00131-01 - RGB LED Strip Reel
- 2X 50CM / 30 LEDs (installed in #88)
92
90
87
89
90
91
92
93
94
600-01744-01
McMaster-Carr 95638A194
603-00805-01
McMaster-Carr 97416A113
Space_Invaders_Rear_
Seat_LED_Assy
McMaster-Carr 90054A194
Space Invaders Frenzy
LED Cap Bracket
Tamper-Resistant Screw for Sheet
Metal, Pin-in-Torx, 18-8 Stainless
Steel, Button Head, Number 8
Size, 1/2" Long, PAINT BLACK
LED Cap Lens
Black-Oxide Steel SAE Flat
Washer, Number 8 Screw Size,
0.188" ID, 0.438" OD
Rear Seat Light Assembly
Flanged Hex Head Screws for
Sheet Metal, Zinc-Plated Steel,
Number 8 Size, 1/2" Long
1
10
2
8
1
4
ITEM NO.
95
96
PART NUMBER
603-00806-01
500-00162-01 (40 CM)
White LED Strip Reel w/ Foam Tape:
DESCRIPTION
LED Cap Back
40CM / 24 LEDs
Space Invaders Frenzy
Rear Seat Light Assembly
Rear Seat LED Cap Assembly
QTY.
1
2
95
NOT SHOWN:
> 6X Wire Ties
96
Page 49
REV.
DESCRIPTION
DATE
7
3
A
RELEASED
11/17/10
12
2
10
4
5
6
8
11
ITEM
NO.
1
2
3
RAW PART NUMBER
608-00201-01
608-00204-01
608-00203-01
HAPP
NUMBER
95-1294-00
95-1295-00
95-1439-00
DESCRIPTION
GRIP, LEFT HALF
TRIGGER, RED
LARGE THUMB BUTTON
QTY.
1
1
1
1
9
4
5
6
7
8
9
10
608-00205-01
608-00216-01
608-00215-01
608-00206-01
608-00207-01
608-00202-01
608-00218-01
95-1315-00
95-0259-00
95-0028-00
95-1297-00
95-1298-00
95-1293-00
96-0110-00
SHAFT, TRIGGER
SWITCH ASSY FOR
THUMB SWITCH
SWITCH ASSY. FOR
TRIGGER
SPRING, TORSION
SPRING,
COMPRESSION
GRIP, RIGHT HALF
TRIGGER BUMPER
1
1
1
1
1
1
1
11
12
MMC 96075A147
MMC 86537A140
GRIP ASSEMBLY
43-0378-00
43-1124-00
SCREW, #8-32 x 1 TP
BLACK
HEX NUT #8-32 BLACK
RAW THRILLS INC.
TITLE:
GRIP ASSEMBLY
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
1
1
REV
A
Page 50
REV.
DESCRIPTION
DATE
18
3
19
13
2
1
ITEM
NO.
1
2
10
PART NUMBER
A
B
C
RELEASED
REVISED
NO CHANGE THIS SHEET
DESCRIPTION
UPPER VACFORM ASSEMBLY
SHAKER ASSEMBLY
10/18/14
1/9/15
12/14/16
QTY.
1
1
15
16
9
7
8
4
3
4
5
6
1718
7
8
9
10
11
12
600-01422-01
600-01423-01
600-01495-01
600-01411-01
600-01420-01
600-01491-01
MMC 96075A211
MMC 96075A183
MMC 90273A827
GRIP ASSEMBLY
PIN PLATE
COVER BRACKET
FRONT VACFORM BRACKET
GRIP PLATE WELDMENT
LARGE GEAR
POT BRACKET
1/4-20 X 1/2" BLK TP SCREW
10-32 X 3/8" BLK TP SCREW
10-32 X 3/8" FLAT HEAD SCREW
2
1
1
1
1
1
1
18
10
6
5
13
MMC 91251A337
10-32 X 5/16" CAP SCREW
8
11
14
12
6
14
15
16
17
18
19
21
MMC 6384K369
MMC 90126A036
MMC 91342A240
600-01567-01
HAPP 50-2670-01
3/4" FLANGED BEARING
3/4" WASHER
3/4" LOCKNUT
CABLE CLAMP
SMALL POT GEAR
POT - 5K
LOWER MECH ASSEMBLY
2
1
1
2
1
1
1
21
NOTES:
1) ALL SCREWS SHOULD BE INSTALLED WITH BLUE LOCTITE 242 or 243.
2) THE 3/4" LOCKNUT (16) IS TIGHTENED UNTIL THE TOP IS FLUSH
WITH THE TOP OF THE TUBE IN THE LOWER MECH ASSEMBLY (21).
TOP ASSEMBLY
RAW THRILLS INC.
TITLE:
GUN MAIN ASSEMBLY
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
REV
C
Page 51
REV.
DESCRIPTION
DATE
19
15
14
21
18
1
ITEM
NO.
1
2
3
4
5
6
7
PART NUMBER
MMC 92313A532
MMC 96075A211
603-00756-01
600-01425-01
MMC 6384K344
600-01418-01
600-01424-01
A
B
C
RELEASED
REVISED
CHANGED TO MOLDED LOWER
COVER
DESCRIPTION
1/4-20 x 3/16" SET SCREW
1/4-20 X 1/2" BLK TP SCREW
LOWER VACFORM
ROCKER BRACKET
3/8" FLANGED BEARING
TUBE STOP BUMPER - 5/8" OD
SIDE PIN
10/18/14
1/9/15
12/14/16
QTY.
1
4
1
1
2
2
1
12
11
6
22
20
4
5
17
8
9
10
11
12
13
14
15
17
18
19
20
21
MMC 90652A029
MMC 90108A413
HAPP 96-4907-00
600-01567-01
HAPP 50-2670-01
600-01426-01
MMC 95229A480
MMC 90566A220
MMC 91257A552
600-01417-01
600-01496-01
MMC 947633A170
1/4-20 THIN LOCKNUT
1/4-20 WASHER
SEGMENT GEAR
POT GEAR
POT - 5K
LOWER TUBE WELDMENT
3/8" WASHER
3/8" THIN LOCKNUT
1/4-20 x 2 1/2 HEX HEAD - GRADE
8
SHORT STOP BUMPER - 3/4" OD
LOWER VACFORM MOUNTING
BRACKET
CABLE CLAMP
RETAINING CLIP
3
1
1
1
1
1
1
1
2
1
1
1
1
NOTE POSITION OF
ORIENTATION HOLE
IN PINCH GUARD
29
26
27
28
13
7
2
22
23
25
26
27
28
29
MMC 90675A009
600-01577-01
600-01739-01
600-01738-01
999-00021-01
999-00017-01
600-01419-01
10
9
8/32" KEPS NUT
GUN ISOLATOR
BOTTOM COVER - RIGHT
BOTTOM COVER - LEFT
6-32 HEX LOCKNUT - BLACK
6-32 X 2.5" PHILLIPS HEAD SCREW -
BLACK
PINCH COVER
1
1
1
1
4
4
1
25
23
8
LOWER MECH ASSEMBLY
NOTES:
1) ALL SCREWS SHOULD BE INSTALLED WITH BLUE LOCTITE 242 or 243.
2) PEEL AND STICK GUN ISOLATOR (#23) TO BOTTOM OF
LOWER TUBE WELDMENT (#14)
RAW THRILLS INC.
TITLE:
GUN MAIN ASSEMBLY
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
REV
C
Page 52
ITEM
NO.
PART NUMBER
DESCRIPTION
QTY.
REV.
A
B
DESCRIPTION
RELEASED
REVISED
DATE
10/18/14
1/9/15
1
2
3
4
5
6
7
8
9
10
600-01576-01
600-01412-01
HAPP FL11629
600-01413-01
600-01414-01
MMC 91375A535
680-00214-01
608-00210-01
HAPP #95-0637-00
MMC 93298A109
COIL MOUNT BRACKET
COIL BRACKET
COIL
COIL ROD
COIL WEIGHT
1/4-20 x 3/8" SET SCREW
BLUE DAMPER PAD
COIL SPRING
COIL SLEEVE
10-32 FLANGED LOCKNUT
4
1
2
1
1
1
2
2
2
8
NO CHANGE THIS SHEET
C
12/14/16
9
3
7
8
5
4
6
2
PEEL AND STICK DAMPER PAD
WITH CENTER HOLE CONCENTRIC
TO COIL BRACKET
1
10
SHAKER ASSEMBLY
NOTES:
1) SET SCREW AND LOCKNUTS SHOULD BE INSTALLED WITH RED LOCTITE 262.
RAW THRILLS INC.
TITLE:
GUN MAIN ASSEMBLY
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
REV
C
Page 53
REV.
DESCRIPTION
DATE
2) INSTALL SEGMENT GEAR AFTER
POT IS ALIGNED FOR EASIER
ACCESS TO GEAR SET SCREW
A
RELEASED
1/15/15
DETAIL A
SCALE 1 : 1
INSTALL WITH GEAR INSTALLED AND POT
FLAT POINTING TOWARD HANDLES
INSTALL 1/16"
(.063") APART
1) ALIGN FLAT ON POT DOWNWARD AND
POINTING TOWARD CENTER OF SEGMENT
GEAR
A
UP AND DOWN
LEFT TO RIGHT
POT ALIGNMENT
POT ALIGNMENT
RAW THRILLS INC.
TITLE:
POT ALIGNMENT DRAWING
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
SEE NOTES
REV
A
Page 54
REV.
DESCRIPTION
DATE
ITEM
NO.
1
2
3
4
5
6
7
8
9
10
PART NUMBER
608-00224-01
600-01922-01
600-01922-01
600-01922-01
600-01923-01
600-01923-01
600-01923-01
500-00223-01
600-01924-01
MMC 90107A029
DESCRIPTION
GREEN BUBBLE BALL
GREEN GUN ACRYLIC - SMALL
GREEN GUN ACRYLIC - MEDIUM
GREEN GUN ACRYLIC - LARGE
BLACK GUN DISCS - SMALL
BLACK GUN DISCS - MEDIUM
BLACK GUN DISCS - LARGE
GUN TIP PCB
GUN TIP BRACKET
WASHER
QTY
1
1
1
1
1
1
1
3
1
1
16
A
RELEASED
11/8/16
11
12
13
14
15
16
17
18
MMC 90145A431
MMC 91287A256
603-00755-01
606-01247-01
606-01249-01
606-01246-01
606-01248-01
MMC 96075A211
1/16" DIA X 2.5" LONG ANTI-ROTATION PIN
M6 X 90MM STAINLESS STEEL HEX BOLT
UPPER VACFORM ASSEMBLY
UPPER LEFT DECAL
LOWER LEFT DECAL
UPPER RIGHT DECAL
LOWER RIGHT DECAL
1/4-20 X .5" BLACK TAMPERPROOF SCREW
1
1
1
1
1
1
1
2
17
13
18
14
8
15
12
11
10
1
2
5
3
6
4
7
9
RAW THRILLS INC.
TITLE:
NOTES:
1) APPLY LOCTITE RED 271 TO HEX BOLT (ITEM 12) THREADS TO SECURE BUBBLE BALL (ITEM 1)
2) APPLY A RAW THRILLS APPROVED ADHESIVE TO THE END OF PIN (ITEM 11) AND INSERT IT INTO SMALL BLACK GUN DISC (ITEM #5)
SPACE INVADERS GUN TIP ASSY
TOL: .X ±.030
.XX ±.015
.XXX ±.005
HOLES: +.002/-.000
ANGLES: ±0.5°
1 of 1
SHEET
MATERIAL:
FINISH:
PART NO.
SEE NOTES
SEE NOTES
REV
A
Page 55
Loading...