Raven E1003925 User Manual

TRANSMISSION

INDICATOR LIGHT

OPERATION GUIDE

STOP BUTTON

Press to immediately stop
all active bed functions.

FLAT BUTTON

Press to return bed
to the level position.

HEAD UP/DOWN BUTTON

Press and hold to raise or

lower the head section.

PROGRAM SET BUTTON

Press to capture any position

of the bed as a programmed
position (3 unique positions).
Press the recall buttons (“P1,

P2 or P3”) to return bed to

any of the preset positions.

To Program Preset Positions:

1. Set the head and/or foot to
the desired position.

2. Press the program set button
once.

3. Press position recall button
“P1” to save position.

4. Repeat steps 1 thru 3 above
to program favorite positions
for “P2” and “P3”.

HEAD MASSAGE BUTTON

Press the “+” symbol to activate the

head massager at a preset intensity.

Press and hold the “+” symbol to

intensify head massager. Press and

hold the “–” symbol to decrease head

massager intensity.

NEUROSAGE WAVE INTENSITY BUTTON

Press and hold the “+” symbol to intensify
Neurosage wave intensity. Press and hold
the “–” symbol to decrease Neurosage
wave intensity.

FOOT UP/DOWN BUTTON

Press and hold to raise or
lower the foot section.

POSITION RECALL BUTTONS

Press to activate a position set
by the program button.

FOOT MASSAGE BUTTON

Press the “+” symbol to
activate the foot massager at
a preset intensity. Press and
hold the “+” symbol to
intensify foot massager. Press
and hold the “–” symbol to
decrease foot massager
intensity.

NEUROSAGE ON/OFF BUTTON

Press to activate or deactivate
the Neurosage wave vibration
system.

MASSAGE NOTE:

When activated, the massage system will launch the prior intensity setting used and automatically
shut off after 30 minutes. To restart Neurosage wave, press the Neurosage on/off button. To restart
head or foot massagers, press the “+” symbol on the head or foot massage button/s.

IMPORTANT:

Read advisory information in the owners manual carefully before using this product. The
potential for electrical shock exists if electrical components are not installed or operated
properly.

See back of page for additional programming features...

Document Part No. 99300799

www.lpadjustablebeds.com

EDR10488 4/05

© Leggett & Platt, Inc.

4002 PROGRAMMING

To set channels on a single base:

4002 BATTERY REPLACEMENT

Requires (2) CR2032 3 volt batteries.

1. Plug the bed into a power
source and within 30 seconds,
press the head up button on
the hand control until the
transmission indicator light
illuminates. This will confirm
that the hand control and the
bed are communicating.

2. The hand control channel is
now programmed.

To set channels for 2 or more
beds to operate independently:

1. Unplug all beds from their
power sources.

2. Plug in the first bed to be
programmed and within 30
seconds, press the head up
button on the hand control until
the transmission indicator light
illuminates. This will confirm
that the hand control and the
bed are communicating.

3. Repeat steps 1 and 2 with each
base requiring programming (It
is important to use the specific
hand control that will be used
to operate the bed). Beds prior
programmed with the remote
need not be unplugged.

REMOVAL:

1. Remove the battery
compartment cover
located on the back of
the hand control
(FIGURE 1).

2. Press the round­shaped tab (FIGURE 2)
and each battery will
eject from the plastic
captive clip (FIGURE 3).

3. Grasp and remove
batteries. Note

position of batteries
when removing for
replacement.

PUSH DOWN
ON TAB TO
EJECT BATTERIES

FIGURE 2

BATTERIES

PUSH IN (SLIGHTLY)
AND SLIDE OFF
BATTERY
COMPARTMENT
COVER

REPLACEMENT:

4. Position the new
batteries face-up
and insert into the
plastic captive clips
(reverse of removal).

5. Carefully push
batteries in and
down to install.

6. Replace battery
compartment cover.

FIGURE 1

4. Multiple beds are now
programmed for independent
operation.

Note: In the event of power
failure or if bed is inadvertently
unplugged from the electrical
power source, wait 30 seconds
(after power is restored) before
using any hand control. This
will prevent bases from
learning and working
simultaneously.

FIGURE 3

WHEN BATTERY EJECTS

FROM CAPTIVE CLIP,

ROTATE UP AND OUT

OF BATTERY

COMPARTMENT

TO REMOVE