Ravelli APGL3 User Manual

APGL3 MODEL TRIPOD

Product Overview

The Ravelli APGL3 is a Professional Quality Tripod providing a solid base for
high-end photographic equipment. This model is all pressure treated aluminum
alloy construction and is unrivalled in stability. The three axis adjustable head
provides smooth fluid adjustment to any angle. The center elevator is gearless and
can be inverted for low angle shots. Dual foam grips, quick release leg locks, a
quick release camera plate and rubber feet/metal spikes complete a very nice
tripod.

Features

 Professional Quality Tripod
 Height Adjustable Center Column
 Three Axis Tilt Adjustment Head
 Quick Release Leg Locks
 Includes Carry Bag

Identifying the parts

Using the Tripod

Set Up

To set up the tripod, Grasp the legs of the tripod, then pull each leg away from the
center until it reaches the first lock position. Do this for each leg then ensure the
tripod is stable before releasing it completely on the ground.

Mounting The Head

To install the 3 axis head, first position the
head on the head mounting plate located on
top of the center column then thread it on the
3/8" screw in a clockwise rotation until the
head is tight. Lastly, tighten the 3 Allen head
screws located underneath the mounting plate
on the center column to secure the head to
the tripod.

Height Adjustment

Adjusting the height of the tripod can be done by simply flipping the leg
height adjuster locks open, then pulling the legs downward until the desired height
is obtained. Flip the leg locks back down to lock the legs into place. The leg height
adjuster flaps are also equipped with Allen screw heads to fine tune the tension
used to lock the leg in place. You can also utilize the center column to raise the
height of tripod further by loosening the center column lock knob , then pulling the
head upwards until the desired height is achieved. Lock the column into place with
the lock knob to prevent the head from retracting back down. (Note: When

adjusting height, extend the thicker leg segment first, as they are thicker and
provide greater stability.)

The Quick Release Plate

To remove the quick release plate, first
flip the silver safety lock (A) to unlock the
plate. Next, flip the quick release plate lever
(B) to allow the plate to pop up and release.

To attach the camera to the quick
release plate, hold camera securely in one

hand, and locate the 1/4” screw hole on

bottom of your camera. Secure the screw of
the quick release plate on the camera by
turning it clockwise.

To insert the quick release plate, insert
the plate into the base cut out near the bubble

level. Once the plate is aligned, press down on the opposite end to allow the lever
(B) to snap close. Ensure the lever is fully in and the quick release plate is fully
secure, then turn the silver safety lever (A) to lock the plate in place.

Panning & Tilting

Tilting - To adjust the tilt angle of the head, turn the tilt handle (F) clockwise
for tightening, counterclockwise for loosening to adjust the angle of tilt. Turn head
adjustment handle until the desired resistance is achieved.

Panning- For smooth consistent panning, tighten or loosen the panning
adjustment handle (G) until the right amount of resistance is obtained. Turning the
handle clockwise will tighten it and make panning slow and firmer. Turning the
handle counter-clockwise to loosen it and will make panning fast and easy. (Note:

Finding the right amount of panning resistance will give you smooth and optimal
speed for great captures. We also recommend the use of sand bags to provide
greater stability when panning.)

Using the Feet: The rubber feet on the tripod
can be removed or retracted to reveal the turf
spikes. To remove the rubber feet, firmly hold the
tripod with one hand and with the other, grasp
one of the feet, then pull down and outward. To
retract the rubber feet, simply turn the feet in a
clockwise rotation until it reaches the top of the
threads.

Notes On The Bubble Level: The included bubble

level is a guide. The exact level position of the
tripod depends on the extension of the legs, the
angle of the legs, whether or not the surface the tripod is sitting on is level or not
etc. Also, the bubble level is off of dead center. Thus, it may read perfectly level
with the tripod head pointing in one direction and then read something other than
perfectly level during a pan. If it is crucial to the user to have perfect true level, we
recommend using a professional separate level at least 6 inches in length or more.

Optional ATD Tripod Dolly*: To easily maneuver your tripod or stands, we recommend our universal
heavy duty Ravelli ATD Tripod Dolly. The ATD dolly is an excellent choice for use with your professional
background stands, light stands, and also video and camera tripods. These dollies offer smooth
movement with 3" rubber wheels and metal ball bearings. The Ravelli ATD also includes a one-step lock
on each wheel to securely hold your tripod in place. The dolly is easily folded and has a carrying handle
built in and includes a protective bag.

WARNING: There is a tipping risk for the fully extended tripods. This can be due to moving the tripods
while fully extended, things such as uneven surfaces or wind. To reduce the risk of tipping over, we
recommend placing one tripod leg facing the same direction as the camera or the heavy part of
mounted equipment to balance the weight. We also recommend purchasing sand bags or weights to set

on the tripod legs to hold the tripod in place. Ravelli™ guarantees the tripod only and is not liable for

damage caused to backdrops, cameras, lighting, or any other items.

Model:

APGL3 Model Tripod

Panning Angle:

360°

Tilt Angle:

90°

Dimensions:

Collapsed Height: 31”
Maximum Height: 66”
Minimum Height: 20” (inverted height is 0)

Mass:

Tripod: 7.1LBS
Shipping Weight: 8 LBS

Quick Release Plate

Screw:

1/4”

Quick Release Plate

Dimensions:

2” x 1.69”
Height Leg Locks:

2 Height Adjustment Leg Locks per leg

Feet Materials:

Rubber feet / Aluminum Spiked Feet

Unit Materials:

Tripod:
Carrying Case: Nylon

Leg Diameter

(per segment)

1st -.90”
2nd- .78
3rd – .66”
4th— .55”

Specifications