Rapid Set RSUF-55P User Manual
Rapid Set Ultraflow
922488 Version #: 01 Revision date: - Issue date: 30-September-2014
SDS US
1 / 7
SAFETY DATA
1. Identification
Product identifier Rapid Set Ultraflow 4000/8
Other means of identification
Product code 185010055, 185013000
Recommended use
Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
Company name
Address
Telephone
E-mail
Contact person
Emergency telephone
number
2. Hazard(s) identification
Physical hazards
Health Hazards
OSHA defined hazards
Label elements
Industrial use.
Workers (and your customers or users in the case of resale) should be informed of the potential
presence of respirable dust and respirable crystalline silica as well as their potential hazards.
Appropriate training in the proper use and handling of this material should be provided as required
under applicable regulations.
CTS Cement Manufacturing Corporation
11065 Knott Ave Suite A
Cypress, CA 90630
United States
1-800-929-3030
info@ctscement.com
Safety Officer
1-800-929-3030 (8 AM - 5 PM)
Not classified.
Skin corrosion/irritation
Serious eye damage/eye irritation
Carcinogenicity
Specific Target Organ Toxicity, Single
Exposure
Specific Target Organ Toxicity, Repeated
Exposure
Not classified.
SHEET
Category 2
Category 1
Category 1A
Category 3 respiratory tract irritation
Category 2 (Lungs)
Signal word
Hazard statement
Precautionary statement
Prevention
Response
Storage Store in dry location.
Disposal
Danger
Causes skin irritation. Causes serious eye damage. May cause cancer. May cause respiratory
irritation. May cause damage to organs (Lungs) through prolonged or repeated exposure.
Obtain special instructions before use. Do not handle until all safety precautions have been read
and understood. Do not breathe dust. Wash thoroughly after handling. Use in a well-ventilated
area. Wear protective gloves/protective clothing/eye protection/face protection.
If exposed or concerned: Get medical advice/attention. If in eyes: Rinse cautiously with water for
several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately
call a poison center/doctor. If on skin: Wash with plenty of water. If skin irritation occurs: Get
medical advice/attention. Take off contaminated clothing and wash before reuse. If inhaled:
Remove person to fresh air and keep comfortable for breathing. Call a poison center/doctor if you
feel unwell.
Store away from incompatible materials.
Dispose of contents/container in accordance with local/regional/national/international regulations.
Rapid Set Ultraflow
922488 Version #: 01 Revision date: - Issue date: 30-September-2014
SDS US
2 / 7
Hazard(s) not otherwise
classified (HNOC)
3. Composition/information on ingredients
None known.
Mixtures
Chemical name
Calcium Sulfoaluminate
Cement
Silica, quartz
CAS number %
960375-09-1 40-60
14808-60-7 40-60
Composition comments
All concentrations are in percent by weight unless ingredient is a gas. Gas concentrations are in
percent by volume.
4. First-aid measures
Inhalation
Skin contact
Eye contact
Ingestion
Most important
symptoms/effects, acute and
delayed
Indication of immediate
medical attention and special
treatment needed
If dust from the material is inhaled, remove the affected person immediately to fresh air. Call a
physician if symptoms develop or persist.
Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Get
medical advice/attention. Wash contaminated clothing before reuse.
Do not rub eyes. Immediately flush eyes with plenty of water for at least 15 minutes. Remove
contact lenses, if present and easy to do. Continue rinsing. Get medical attention immediately.
Immediately rinse mouth and drink plenty of water. Call an ambulance and take these instructions.
Get medical attention if symptoms occur.
Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred
vision. Permanent eye damage including blindness could result. Upper respiratory tract irritation.
Coughing. Discomfort in the chest. Shortness of breath. Wheezing. Skin irritation.
Provide general supportive measures and treat symptomatically. Keep victim under observation.
Symptoms may be delayed.
General information
If you feel unwell, seek medical advice (show the label where possible). Ensure that medical
personnel are aware of the material(s) involved, and take precautions to protect themselves. Show
this safety data sheet to the doctor in attendance.
5. Fire-fighting measures
Suitable extinguishing media
Unsuitable extinguishing
media
Specific hazards arising from
the chemical
Special protective equipment
and precautions for firefighters
Fire fighting
equipment/instructions
Specific methods
General fire hazards
Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).
Do not use water jet as an extinguisher, as this will spread the fire.
During fire, gases hazardous to health may be formed.
Self-contained breathing apparatus and full protective clothing must be worn in case of fire.
Move containers from fire area if you can do so without risk.
Use standard firefighting procedures and consider the hazards of other involved materials.
No unusual fire or explosion hazards noted.
Rapid Set Ultraflow
922488 Version #: 01 Revision date: - Issue date: 30-September-2014
SDS US
3 / 7
6. Accidental release measures
Personal precautions,
protective equipment and
emergency procedures
Methods and materials for
containment and cleaning up
Environmental precautions
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Do not breathe dust. Use a
NIOSH/MSHA approved respirator if there is a risk of exposure to dust/fume at levels exceeding
the exposure limits. Do not touch damaged containers or spilled material unless wearing
appropriate protective clothing. Ensure adequate ventilation. Local authorities should be advised if
significant spillages cannot be contained. For personal protection, see section 8 of the SDS.
Stop the flow of material, if this is without risk. If sweeping of a contaminated area is necessary
use a dust suppressant agent which does not react with the product. Collect dust using a vacuum
cleaner. Minimize dust generation and accumulation. Prevent entry into waterways, sewer,
basements or confined areas. Following product recovery, flush area with water. For waste
disposal, see section 13 of the SDS.
Avoid discharge into drains or water courses.
7. Handling and storage
Precautions for safe handling Provide appropriate exhaust ventilation at places where dust is formed. Minimize dust generation
and accumulation. Do not breathe dust. Do not get this material in contact with eyes. Avoid
prolonged exposure. Wear appropriate personal protective equipment. Observe good industrial
hygiene practices.
Conditions for safe storage,
including any incompatibilities
Store in original tightly closed container. Store in dry location. Store away from incompatible
materials (see Section 10 of the SDS).
8. Exposure controls/personal
protection
Occupational exposure limits
US. OSHA Table Z-3 (29 CFR 1910.1000)
Components
Silica, quartz (CAS
14808-60-7)
US. ACGIH Threshold Limit Values
Components
Silica, quartz (CAS
14808-60-7)
US. NIOSH: Pocket Guide to Chemical Hazards
Components
Type
TWA 20 mppcf
0.3 mg/m3 Total dust.
Value
Form
0.1 mg/m3 Respirable.
Type
TWA 0.025 mg/m3 Respirable fraction.
Type
2.4 mppcf Respirable.
Value
Value
Form
Form
Silica, quartz (CAS
14808-60-7)
Biological limit values
Exposure guidelines
No biological exposure limits noted for the ingredient(s).
Occupational exposure to nuisance dust (total and respirable) and respirable crystalline silica
should be monitored and controlled.
TWA 6 mg/m3
TWA 0.05 mg/m3 Respirable dust.
Loading...