Rapidline SS-SPCNR PS Assembly Instructions Manual

SS-SPCNR PS

Assembly instructions

Assembly instruction |

2

TABLE OF CONTENT

1. SAFETY AND WARNINGS

2. USAGE

3. SET UP AND INSTALLATION

4. OPERATION

5. MAINTENANCE AND DEFECTS

6. TECHNICAL DATA

7. PARTS

8. ASSEMBLY DIRECTIONS

9. DECLARATION OF CONFORMITY

2. USAGE

– The electromotive, height-adjustable tables are designed for workstations in dry work environments only ( 0 - 40° C ; 20 - 90 % relative

humidity). The table height is innitely adjustable, so that it can be set to the most ergonomically suitable working level.

– They have not been designed for other purposes than those included in this manual, e.g. they are not to be used in areas of

high humidity or dampness, nor for lifting people. Any other use is at one’s own risk !

– Do not crawl, lie or move around under the table frame, and do not sit or stand on the table frame.

– CHILDREN should only use the table when supervised by adults.

– Liability : The manufacturer accepts under no circumstances warranty claims or liability claims for damages arising from improper use

or handling of the table frame other than that described in this operation manual.

3. SET UP AND INSTALLATION

When the table has been assembled ( see assembly directions in CHAPTER 8 ) the adjustable feet are installed so that the table is level
and does not shift. Then the table is connected to the 100 -240 VAC outlet and the table is ready for use.

– Make sure that no cables can get jammed.

– Place the table in a safe distance from window frames, radiators, furniture etc. so that people do not get stuck.

– Do not place any objects above 550 mm underneath the table.

– When moving the table after it has been assembled, the tabletop needs to be removed. The table CANNOT be lifted by the tabletop.

The desk need to be lowered to minimum height before moving.

1. SAFETY AND WARNINGS

This table complies with the prescribed safety regulations. Inappropriate use may cause damage to persons and table.

Please read the operation manual prior to using the table. It provides you with important information about safety, use,
installation and maintenance of the table, and thus protecting you and your children and avoiding damage on the table.

Please guard this operation manual and pass it on to any future owner !

IMPORTANT NOTES!

Prior to installation, use and

maintenance of the table frame, any

installer and any user of the table

must study this assembly and operation

manual carefully, so as to gain a complete

understanding of its contents.

WARNING : FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS

AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN SERIOUS BODILY INJURY.

Assembly instruction |

3

4. OPERATION

UP / DOWN operation :
Push the buttons for operation up or down

5. MAINTENANCE AND DEFECTS

– The table does not require any maintenance by usage as described in chapter 2 in the directions for use.

– The table is only to be maintained with a damp cloth.

– In the event of the occurrence of jarring sounds during operation, STOP using the table and please contact the dealer.

6. TECHNICAL DATA

Frame, materials : Steel, powder lacquered

Weights ( frame ): 27 kg | 29 kg | 31 kg

Width : 1200 x 1200 mm | 1500 x 1500 mm | 1800 x 1800 mm

Depth : 700 mm

Height ( frame ) : 660 -1180 mm

V ( speed ) : ~ 25 mm / sec., depends on load.

F

MAX

= Max. load : 100 kg ( evenly distributed on frame )

Duty cycle : 10 % by 50 % of max. load on frame or max. 2 min. continuously

Operation : Micro switches

Voltage : 100 -240 VAC | 50 / 60 Hz

Consumption : 80 Watt

Standby Consumption : < 0,4 Watt

Above specications may vary depending on local temperature, humidity and input voltage.

7. PARTS See page 4.

8. ASSEMBLY DIRECTIONS See pages 5 - 7.

9. DECLARATION OF CONFORMITY

We hereby declare, under our sole responsibility that the following products :

– Sit and stand table product type SSSPLEG PS combined with SSSPCNR PS

is in accordance with :

– Directive 2006 / 42 / EF of The European Parliament and of the Council of 17 May 2006 on machinery

and on changes of directive 95 / 16 / EF

With reference to the above please be aware that :

– the sit and stand table is considered a machine and

– the sit and stand table may not be used until it has been assembled and installed according to the instructions.

Manufacturer :

FurnX Pty Ltd
PO Box 357
Zillmere, QLD 4034
Australia

Phone : [phone] / Fax : [phone]

www.rapidline.com.au

Assembly instruction |

4

Driveshaft

x 1

7. Parts

A1

Legs

A2

x 1

A3

3rd leg

x 1

x 1 x 2

B1

B2

x 1

Transformer

D

x 8

M6 * 16H screws

I

x4

Adjustable glide

H

x 13

5 * 16H screws

J

x 2

Cable clips

K

Transformer bracket

M

x 2

4 * 16H screws

L

Cable tie

N

Power cable

E

x 1

Modesty panel

C

Supplied in a separate package.

x 2

Controller

F

x 1

Stiening rail incl.
20 pcs. 5 * 20H screws

NB : Stiening rail is not required

for 1200 W desks.

G

Supplied in a separate package.

x 2

packed with and

packed with

A2A1B1

B2 A3

Assembly instruction |

5

8. Assembly directions

2.

C

C

Pre-tted

A3

A2

A1

H

I

1.

Screws
pre-tted

A3

A3

Assembly instruction |

6

3.

– Fit tabletop, rst centre top and ensure that

the correct length screw is used.

– Desk frame and top have to be parallel

before xing the top

– Do NOT start the desk before top is xed to A1 and

A2

– See component positions on page 8

4.

– Fit telescopic driveshafts – extend both ends

onto driveshaft spigots.

– Do not over-tighten grup screws.

Only very light pressure required.

B2

B1

J

X 1 = X

2

X

1

X

2

F

K

L

M

N

E

D

J

Assembly instruction |

7

5.

6.

– Stiening rail G is not required for

tabletops width 1200W

– See component positions on page 8

– Raise desk and t remaining screws to

stiening rail G and screws to

A3

– See component positions on page 8

G

G

5*20H - 5 pcs.

J

5*20H - 5 pcs.

5*20H - 5 pcs.

5*20H - 5 pcs.

Assembly instruction |

8

Components position and wiring

How to create space for wiring

To ensure correct up and down operation of the desk frame
it has to be tted with a tabletop or applied a similar weight.
Without a tabletop tted, the desk frame may not operate in
the downward direction.

Red / Red

Important :
Only plug leads red to red
and black to black.

Black / Black

343230.0

1

Remove screw

2

Tilt out cover

Cover need to be tted again after wiring.