RangeXTD Range Extender Instruction Manual
RangeXTD WiFi Extender IM
FRONT SIDE
WiFi Range Extender
Instruction Manual
STEPS
The mode selector on the device must be set to the “Repeater”
1.
position for Repeater Mode.
2.
Plug the device into a wall socket. Turn on the device.
3.
Press the WPS button for 1-2 seconds on the device. The WPS LED
will slowly flashing for approx. 2 minutes.
Within these 2 minutes, please press the WPS button of your
4.
Wireless Router directly for 2-3 seconds. (For further details, please
read the operating instructions for your wireless router.)
The device will then automatically connect to your wireless router and copy the
wireless key settings. The device's WiFi password will be the same as your AP/
Router. After you have finished rebooting, please go to your smart device (ie:
phone, computer, TV, TV box, etc) WLAN setting to connect to the new SSID.
Configure via Web Browser (if no WPS button on router)
If your wireless router does not support WPS, you can configure the WiFi
Repeater Mode by connecting it with your smartphone/tablet/computer/laptop with
enclosed RJ45 cable or wirelessly.
Internet
Router RangeXTD Wireless devices
06
Introduction
RangeXTD is best used on Repeater Mode by extending your existing 802.11n
wireless WiFi signal to black spots around your home or workplace. On Router
Mode It can also be used as a WiFi router when wired to your modem or on AP
Mode when wired to your existing wireless router. RangeXTD supports 2.4G
wireless network connection, and it can support 2.4G transmission speeds of up
to 300Mbps. It has 2X built-in antennas and provides excellent wireless
performance, transmission rates and stability technology automatically avoids
channel conflicts using its channel selection feature.
Package Contents
• 1 x WiFi Extender/AP/Router (the device)
• 1 x Instruction Manual
• 1 x RJ45 Cable
V.2
01 03
A. Configure the WiFi Repeater Mode wirelessly
Hardware Overview
Default Setting
URL: 192.168.7.234
Login Password: admin
Wi-Fi SSID: RANGEXTD WiFi Key: None
7
1
Power On/Off
2
8
1
11
2
3
WPS Button:
Press once to initiate WPS mode, press and hold WPS button for 6 seconds to
activate WPS search mode on your device (on Repeater Mode).
Reset Pinhole Button:
Press and hold 3 Seconds to reset the device.
The login screen below will appear. Enter the default password
A4.
9
10
4
5
6
02
WPS Button
3
Mode Selector
4
Reset Pinhole Button
5
WAN/LAN Port
6
LAN Port
7
3 Stage WiFi Signal
Indicators
8
Power/WPS LED
Indicator
9
WAN/LAN LED Indicator
10
LAN Indicator
11
AC Power Plug
“admin” and then click ‘Login’.
A1.
The mode selector must be set to
the “Repeater” position for
LED Indicators
ON: The Device is power on
POWER/WPS
LAN
WAN/LAN
OFF: The Device is not receiving electrical power
Slow Flashing: The Device WPS waiting client connection
Fast Flashing: The Device connecting to your AP/Router
ON: The Ethernet port is connected
OFF: The Ethernet port is disconnected
Flashing: Data transferring
WiFi Signal Strength Indicators
(refer to the diagram on the right)
1
2
ON ON
ONON
ON
OFF
OFFOFF
OFF OFF
3
Description
Wi-Fi Signal output power 100%
Excellent reception
signal strength 50% to 100%
Good reception
signal strength 25% to 50%
Weak reception
signal strength below 25%
Disconnected
.
Mode
AP/Router
Repeater
From the list, select a WiFi SSID. After having selected a WiFi
A6.
SSID, you must then key in the password of that wireless router.
ON
ON
ON
ON
Flashing
You can also give a new name for your RANGEXTD repeater.
3
2
1
Repeater Mode. Plug the device
into a wall socket. Turn device on.
Click on the network icon ( or )
A2.
on the right bottom of your desktop.
You will find the signal called
Password
English
LOGIN
placeholder only
RANGEXTD. Click on ‘Connect’
then wait for a few seconds.
When connected, open your web
A3.
browser and enter 192.168.7.234 in
the browser address box. This
number is the default IP address for
this device.
07
After logging in, you will see the web page below, click on the
A5.
“Repeater” button to start setup.
Wizard
Repeater Mode
Device Information
Wireless LAN
SSID
RANGEXTD
Channel
AUTO
Security
NONE
Management Status
Password
Save/Reload Setting
Upgrade Firmware
Reboot Device
placeholder only
08
IP Adress
Gateway
DHCP
Firmware Version
UpTime
Build Time
InternetWiFi AP/RouterUser-PC Repeater
192.168.7.234
192.168.7.1
Enable
WR18_V110.
0 Day, 00:01:28
2020-12-03 18:38
placeholder only
When entered, click on the “Apply” button to configure and reboot.
After the reboot, please go to your device WLAN setting, connect to
the new WiFi SSID.
09 10
Getting Started
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown below), please do the following:
WIRELESS REPEATER MODE
The device copies and reinforces the existing
wireless signal to extend the coverage of the
signal. This mode is especially useful for a
large space to eliminate signal-blind spots.
This mode is best for a large house, office,
warehouse or other spaces where the
existing signal is weak.
Router
WIRELESS AP MODE
The device is connected to a wired network
then transforms the wired Internet access into
wireless so that multiple devices can share the
Internet. This mode is best used when there is
intereference between rooms like a basement.
Extend wired connection from router to device
in basement to gain wireless signal to that area.
LANRouter
ROUTER MODE
The device is connected to a DSL or cable
modem and works as a regular wireless
router. This mode is fit for an environment
where Internet access from DSL or cable
modem is available for one user but more
users need to share the Internet.
04 05
ADSL
WAN
B. Configure the Wi-Fi Repeater Mode with RJ45 Cable.
B1.
Plug the Device into a wall socket. Turn on device. Connect your
computer / laptop with the Device with RJ45 Cable.
Follow process A3 to A6 to configure the Device.
B2.
Resetting RANGEXTD
To restore factory default settings, press and hold the RESET pinhole button
for 10 seconds and then release, the indicators will all turn off. After you reset
your device, unplug the it for 3 seconds. Plug it back in and wait about 30
seconds, then check your WiFi network for the network called ‘RANGEXTD’
on your computer or mobile device.
*If your device is already configured to your network, you cannot access the
default IP address (192.168.7.234). You must reset the device to access
again.
Scan the below QR code for video instructions.
placeholder only
CONFIGURING THE WIFI REPEATER MODE
Configure via WPS Button
This is the easiest way to configure the device. First, check whether your
wireless router supports WPS. For further details, please read the operating
instructions for your wireless router. If your router does not have a WPS
button, skip this page and follow the next page “Configure via Web Browser”.
Quick and Easy
Tips: If you want to keep the stable connection between your router and RangeXTD on
REPEATER mode, please install the device at a suitable position.
You can find a suitable position by checking the signal indicator on the device, if the LED
is below 2 levels, please find new location.
CONFIGURING THE WIFI AP MODE
Use the AP Mode to obtain a “wireless access point”. The wireless end
devices will connect to the RANGEXTD in this mode. You can also use
this mode, for example, to make a formerly non-wireless-enabled router
wireless-enabled.
Internet
LANRouter
RangeXTD Wireless devices
11
尺寸:100x92mm
105銅版紙彩色,折疊
PROPERTY OF DFO GLOBAL VER 2.0 Jan 05, 2021
CONFIDENTIAL DOCUMENT
Wizard
InternetWiFi AP/RouterUser-PC Repeater
Device Information
SSID
Channel
Security
Password
Save/Reload Setting
RANGEXTD
AUTO
NONE
192.168.7.234
192.168.7.1
Enable
IP Adress
Gateway
DHCP
Firmware Version
UpTime
WR18_V110.
0 Day, 00:01:28
Repeater Mode
Wireless LAN
Management Status
Wizard
InternetWiFi AP/RouterUser-PC Repeater
Device Information
SSID
Channel
Security
Password
Save/Reload Setting
RANGEXTD
AUTO
NONE
192.168.7.234
192.168.7.1
Enable
IP Adress
Gateway
DHCP
Firmware Version
UpTime
WR18_V110.
0 Day, 00:01:28
Repeater Mode
Wireless LAN
Management Status
RangeXTD WiFi Extender IM
BACK SIDE
STEPS
The mode selector must be set to the “AP” position for Access Point
1.
Mode.
2.
Plug the device into a wall socket. Turn on device. Connect your
router with the Device with RJ45 cable.
When connected, open your web browser and enter 192.168.7.234
3.
in the browser address box. This number is the default IP address for
this device.
The login screen below will appear. Enter the default password
4.
“admin” and then click “Login”.
Password
English
placeholder only
LOGIN
12 13
8*.
If Static IP is selected, please enter the IP Address, Subnet Mask,
Default Gateway, DNS, etc.
placeholder only
9*.
Enter the device wireless parameter. It’s recommended that you
rename an SSID, choose an Authentication Mode and create a
WiFi Password. Click “Apply” button, it will restart. Wait for a few
seconds the Device is ready for use.
SSID
Authentication
Mode
Password
Create the wireless SSID/Name of the device
Setup the wireless security and encryption to
prevent unauthorized access and monitoring.
Supports WPA, WPA2, WPA/WPA2 encryption
methods.
Create a password for the device
18
After logging in, you will see the web page below, click on the “AP”
5.
button to start setup.
Wizard
AP Mode
Device Information
Wireless LAN
SSID
RANGEXTD
Channel
AUTO
Security
NONE
Management Status
Password
Save/Reload Setting
Upgrade Firmware
Reboot Device
The following message will be displayed on your web browser:
6.
Enter the device wireless parameter. It’s recommended that you
rename an SSID, choose an Authentication Mode and create a
WiFi Password.
Click on “Apply” button, the device will restart.
placeholder only
Password
placeholder only
IP Adress
Gateway
DHCP
Firmware Version
UpTime
Build Time
InternetWiFi AP/RouterUser-PC Repeater
192.168.7.234
192.168.7.1
Enable
WR18_V110.
0 Day, 00:01:28
2020-12-03 18:38
After the reboot has been completed, please use your smart device’s
(smartphone/tablet/computer/laptop etc) WLAN setting to connect to
new WiFi SSID that you created.
Resetting RANGEXTD
To restore factory default settings, press and hold the RESET pinhole button
for 10 seconds and then release, the indicators will all turn off. After you reset
your device, unplug the it for 3 seconds. Plug it back in and wait about 30
seconds, then check your WiFi network for the network called “RANGEXTD”
on your computer or mobile device.
*If your device is already configured to your network, you cannot access the
default IP address (192.168.7.234). You must reset the device to access
again.
Scan the below QR code for video instructions.
placeholder only
19
SSID
Create the wireless SSID/Name of the device
Setup the wireless security and encryption to
Authentication
Mode
prevent unauthorized access and monitoring.
Supports WPA, WPA2, WPA/WPA2 encryption
methods.
Password
Click on “Apply” button, the device will restart.
After the reboot has been completed, please use your smart device’s
(
smartphone/tablet/computer/laptop etc) WLAN setting to connect to new WiFi
SSID that you created.
Create a password for the device
Resetting RANGEXTD
To restore factory default settings, press and hold the RESET pinhole button
for 10 seconds and then release, the indicators will all turn off. After you reset
your device, unplug the it for 3 seconds. Plug it back in and wait about 30
seconds, then check your WiFi network for the network called ‘RANGEXTD’
on your computer or mobile device.
*If your device is already configured to your network, you cannot access the
default IP address (192.168.7.234). You must reset the device to access
again.
Scan the below QR code for video instructions.
placeholder only
Change Management Password
Default password of the device is “admin”, and
it’s displayed on the login prompt when
accessed from web browser. There’s a
security risk if you don’t change the default
password, since everyone can see it. This is
very important when you have the wireless
function enabled.
To change password, please follow the
following instructions:
Please click “Password” button on the
management setting interface, the following
message will be displayed on your web
browser:
Click “Apply” button, the Device will log off.
If you forgot your existing password, you can reset the password by clicking the
reset pinhole button on the side of the device for 10 seconds and then release,
the indicators will all turn off. After you reset your device, unplug the it for 3
seconds. Plug it back in and wait about 30 seconds, then check your WiFi
network for the network called ‘RANGEXTD’ on your computer or mobile device.
14
Device Information
Wireless LAN
SSID
Channel
Security
Management Status
Password
Save/Reload Setting
Upgrade Firmware
Reboot Device
placeholder only
20
Wizard
Repeater Mode
InternetWiFi AP/RouterUser-PC Repeater
RANGEXTD
AUTO
NONE
IP Adress
Gateway
DHCP
Firmware Version
UpTime
Build Time
192.168.7.234
192.168.7.1
Enable
WR18_V110.
0 Day, 00:01:28
2020-12-03 18:38
CONFIGURING THE WIFI ROUTER MODE
The device is connected to a DSL or cable
modem and works as a regular wireless
router. Internet access from DSL or cable
modem is available for one user but more
users need to share the Internet.
STEPS
The mode selector must be set to the “Router” position for Router
1.
Mode.
Plug the Device into a wall socket.
2.
3.
Connect your DSL Modem with the Device with RJ45 Cable.
When connected, open your web browser and type 192.168.7.234 in
4.
the browser address box. This number is the default IP address for
this device.
The login screen below will appear. Enter the default password
5.
“admin” and then click ‘Login’.
Password
English
placeholder only
LOGIN
Firmware Upgrade
The system software used by this router is
called “Firmware”, just like any applications
on your computer, when you replace the old
application with a new one, your computer will
be equipped with new functions. You can also
use this firmware upgrade function to add new
functions to your router, even fix the bugs of
this router.
Please click “Upgrade Firmware” located at
the management setting interface, and then
the following message will be displayed on
your web browser:
placeholder only
Click “Browse...” or “Choose File” button first; you’ll be prompted to provide the
filename of firmware upgrade file. Please download the latest firmware file from
our website, and use it to upgrade your router.
After a firmware upgrade file is selected, click “Upload” button, and the device
will start firmware upgrade procedure automatically.
The procedure may take serveral minutes, please be patient.
Note:
•
Never interrupt the upgrade procedure by closing the web browser or physically disconnect your
computer from the device. If the firmware you uploaded is interrupted, the firmware upgrade will fail,
contact customer support for assistance if needed.
Warranty is void if you interrupted the upgrade procedure.
•
21 22 23
Wizard
Repeater Mode
Device Information
Wireless LAN
SSID
Channel
Security
Management Status
Password
Save/Reload Setting
Upgrade Firmware
Reboot Device
ADSL
WAN
InternetWiFi AP/RouterUser-PC Repeater
RANGEXTD
AUTO
NONE
IP Adress
Gateway
DHCP
Firmware Version
UpTime
Build Time
192.168.7.234
192.168.7.1
Enable
WR18_V110.
0 Day, 00:01:28
2020-12-03 18:38
After logging in, you will see the web page below, click on the “Router”
6.
button to start setup.
Wizard
Router Mode
Device Information
Wireless LAN
SSID
RANGEXTD
Channel
AUTO
Security
NONE
Management Status
Password
Save/Reload Setting
Upgrade Firmware
Reboot Device
placeholder only
IP Adress
Gateway
DHCP
Firmware Version
UpTime
Build Time
InternetWiFi AP/RouterUser-PC Repeater
192.168.7.234
192.168.7.1
Enable
WR18_V110.
0 Day, 00:01:28
2020-12-03 18:38
Choose your WAN Connection Type.
If DHCP is selected, please
follow step 7.
placeholder only
If PPPOE is selected, please
follow steps 7* to 9*.
placeholder only
16
How to Connect your Computer/Laptop with the Device
Adding a wireless computer to the device
Log on to the computer.
1.
Connect to a network by right-clicking the
2.
network icon ( or ) in the notification area.
Choose the wireless network from the list
3.
that appears, and then click Connect.
Type the network security key or passphrase
4.
if you are asked to do so, and then click OK.
You’ll see a confirmation message when you
are connected to the network.
To confirm that you added the computer, please do the following:
5.
Open network by clicking the Start button , and then clicking Control
Panel. In the search box, type network, and then, under Network and
Sharing Center, click View network computers and devices. You should
see icons for the computer you added and for the other computers and
devices that are part of the network.
Note:
If you don’t see icons in the Network folder, then network discovery and file sharing might be
turned off.
Scan the below QR code for MAC set up
placeholder only
7.
Enter the device wireless parameter. It’s recommended that you
rename an SSID, choose an Authentication Mode and create a WiFi
Password. Click “Apply” button, it will restart. Wait for a few seconds
the Device is ready for use.
SSID
Authentication
Mode
Password
Choose your WAN connection type.
7*.
If PPPoE (ADSL Dial-up) is selected, please enter the Account and
Password from your ISP, these fields are case-sensitive.
Create the wireless SSID/Name of the device
Setup the wireless security and encryption to
prevent unauthorized access and monitoring.
Supports WPA, WPA2, WPA/WPA2 encryption
methods.
Create a password for the device
placeholder only
17
Difficulties with setting up your Device?
We are here to help!
Please visit https://support.myrangextd.com/ or
scan the QR code for any urgent inquiries!
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as
household or general waste. It should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment,
FCCID NO: 2AVK9-30251
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any inte rference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
Canada EMC statement
This device complies with RSS 210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES-003.
This equipment complies with Canada radiation exposure limits set forth for uncontrolled environments. This equipment
should be installed and operated with a minimum distance of 20cm （may be adjusted according to actual calculation
result） between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
or returned to the supplier for disposal.
尺寸:100x92mm
105銅版紙彩色,風琴折疊
PROPERTY OF DFO GLOBAL VER 2.0 Jan 05, 2021
CONFIDENTIAL DOCUMENT
Loading...