Page 1
Forward this manual to all operators.
Failure to operate this equipment as
directed may cause injury and/or
INSTALLATION AND OPERATION MANUAL
property damage.
FLOOR
JACKS
(Professional &
Speedy Series)
RFJ-3T
RFJ-3TP
SHIPPING DAMAGE CLAIMS
When this equipment is shipped, title passes
to the purchaser upon receipt from the carrier. Consequently, claims for the material
damaged in shipment must be made by the
purchaser against the transportation compa ny at the time the shipment is received.
MODELS
RFJ-3T
RFJ-214TP
RFJ-3TP
RFJ-214TQ
RFJ-3TQ
RFJ-3TQ
BE SAFE
Your new ranger floor jacks are designed and
built with safety in mind. However, your overall safety can be increased by proper training
and thoughtful operation on the part of the
operator. DO NOT operate or repair this
equipment without reading this manual and
the important safety instructions shown
inside.
Bend - Pak Inc.
1645 Lemonwood Drive
Santa Paula, CA 93060, U.S.A
Tel: 805 933 9970 - Fax: 805 933 9160
“The Benchmark Of Quality”
Page 2
UPON DELIVERY
Width
Width
84 lbs.
88 lbs.
96 lbs.
98 lbs.
1. Carefully remove all packaging material.
2. Inspect the equipment and all parts for any signs of concealed shipment or
storage damages.
3. Remember to report any shipping damage to the carrier and make a notion on
the delivery receipt.
IMPORTANT SAFETY TIPS
Be sure to read all warning labels and the instruction manual prior to operation of this
equipment.
Keep hands and body clear of all pinch points.
Use the jack for loading under-rated capacity only. DO NOTover load.
Ensure the jack is set on a solid and level surface.
Support the load with jack stands after the load is raised to the desired level, before get-
ting under the load.
Center the load on the jack saddle properly. An off centered load may damage the seals
and result in jack failure.
Lift only dead weight. Always set the hand brake and block the wheels of the vehicle.
This Jack is to be used by professional personnel only. In order to avoid a dangerous sit-
uation, please ensure that non professional personnel and especially CHILDREN DO
NOT USE this Jack under any circumstances.
SPECIFICATIONS / FEATURES
Model Lifting
Capacity
RFJ-3T
RFJ-214TP
RFJ-3TP
RFJ-214TQ
RFJ-3TQ
6,000 lbs.
2,722 Kg
4,500 lbs.
6,000 lbs.
2,722 Kg
4,500 lbs.
6,000 lbs.
2,722 Kg
2,004Kg
2,004Kg
Lowered
Height
5 3/4"
121mm
5"
127mm
5 1/4"
133mm
4 1/2"
110mm
4 1/2"
110mm
raised
Height
21 1/2"
521mm
19 1/4"
489mm
19 1/4"
489mm
20 1/2"
510mm
20 1/2"
510mm
Front
Overall
11"
297mm
10 3/4"
273mm
10 3/4"
273mm
11"
279mm
11"
279mm
Rear
Overall
15 1/2"
368mm
13 1/2"
343mm
13 1/2"
343mm
14 1/2"
368mm
15 1/2"
368mm
Overall
Length
28"
711mm
26"
660mm
26"
660mm
28"
711mm
28"
711mm
Shipping
Weight
110 lbs.
50Kg
38 Kg
40 Kg
44 Kg
45 Kg
Page 3
ASSEMBLY INSTRUCTION
This equipment comes to you pre-assembled except for the pump handle and the foot
paddle. (foot paddle for models RFJ-214TQ / RFJ-3TQ)
All models: The two sections of the handle should be assembled by sliding the
lower part of the handle into the top part and affixing the screw through
both parts.
Loosen the hex head bolt on the handle socket of the jack and insert
the assembled handle into the socket and tighten the bolt, holding the
handle in place.
Models RFJ-214TQ & RFJ-3TQ: Using the nut & bolt on the foot paddle, attach the pad-
dle to the “roller cam plunger assembly” on the back of the handle socket.
OPERATION INSTRUCTIONS
It is always good practice to inspect the equipment before use to ensure that it has no
damages, missing parts or oil leakages. Refer to the owner’s manual of the vehicle to
learn about the correct lifting points on the vehicle.
TO LIFT: Lower the Jack to the minimum and position it under the prop-
er lifting points of the vehicle. Turn the pump handle clockwise
to close the release valve and pump the handle. Never use
this jack to move or dolly a load.
With models RFJ-214TQ and RFJ-3TQ, you may use the foot
paddle to raise the jack instead of the pump handle.
TO LOWER: Simply turn the pump handle counter clockwise slowly.
MAINTENANCE: Have all moving parts well lubed. Using a grease gun, grease
the elevator arm pivot pin grease fitting.
Store the jack in a well ventilated, dry place away from sun
light. When not in use keep the elevator arm lowered to the
minimum.
On a regular basis clean the jack to remove any dust, rust, dirt
etc. that could hinder performance.
INFORMATION: Use only “Hydraulic jack fluid” SAE 10 or equivalent.
Loading...