110 Ceramic Electric
Users Guide
&
Installation & Service Instructions
U107230 - 01
2
Be safe
Warning
Accessible parts will become hot in use. To avoid burns and scalds children
should be kept away.
Do not stand or rest heavy objects on the hob. Although the ceramic surface is
very strong, a sharp blow or sharp falling object might cause the surface to crack.
As soon as any crack in the surface becomes visible disconnect the appliance
immediately from the supply and arrange for its repair. Care should be taken that
no water seeps into the appliance.
During use, and afterwards, the appliance will be warm, so be careful with little
children. If the younger members of your family are allowed into the kitchen we
strongly advise that they are kept under supervision at all times.
If you have not used a ceramic electric cooker before, we recommend you read the
‘General Safety Instructions’ where we describe some basic guidelines on how to
use your cooker safely.
Electricity on
Make sure that the electricity supply is turned on.
Peculiar smells
When you fi rst use your cooker it may give off a slight odour. This should stop after
a little use.
Before using for the fi rst time, to dispel manufacturing odours turn the ovens
to 240°C and run for an hour. Make sure the room is well ventilated to the
outside air, by opening windows for example.
3
Contents
The Hob Page 4
The Ovens Page 6
The Clock Page 7
Cooking using the timer Page 8
Multi-function oven Page 9
The Handygrill Page 11
Using your Handygrill Page 11
Oven shelves Page 12
Oven light Page 12
Storage Page 12
Multi-function Oven cooking guide Page 14
Cooking chart - Conventional and full Fan oven functions Page 15
Cleaning your cooker Page 16
Cleaning Table Page 17
Troubleshooting Page 18
General Safety Instructions Page 20
Installation Page 22
Servicing Page 26
Circuit Diagram Page 30
Technical Data Page 31
4
The Hob
When you cook on a ceramic hob its very important
to use the right sort of pans...
1
Use only pans that are suitable for ceramic hobs.
We recommend stainless steel and enamelled steel
pans because pots and pans with copper or aluminium
bases leave traces on the hob that are diffi cult to
remove.
Glass-ceramic cookware is not suitable because of its poor
conductivity.
2
Pots and pans should have thick, smooth, fl at bottoms.
This ensures that there is the maximum heat transfer from
the hob to the pan, making cooking quick and energy
effi cient.
Never use a round bottomed Wok even with a stand.
3
The very best pans have bases that are very slightly
curved in when cold. If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up
the metal expands and lies fl at on the cooking surface.
Make sure that the base of the pan is clean and dry to
prevent any residue burning onto the hob panel. This
also helps prevent scratches and deposits (such as lime
specks).
4
Always use pans that are the same size as (or slightly
larger than) the areas marked on the hob top. Using
smaller pans wastes heat, and any spillage will be burnt
on. Using a lid will help the contents boil more quickly.
5
Always lift pans off the hob. Sliding pans may cause marks
and scratches. Always turn the control to the off position
before removing a pan.
6
There are indicator lights for each of the cooking areas.
These come on when a hob control is turned on and
stay lit while the surface cools. Always take care before
touching the surface even when it is turned off - it may be
hotter than you think.
7
The ratings of the cooking areas are shown on the
diagram above.
8
On the right of the hob is a dual purpose area. The
inner ring marks out a 1.2kW hob area, the outer line
marks the extent of the Warmer. Turn the control to the
fi rst (Warmer) position to heat the whole area to a low
temperature. Use the Warmer for keeping food warm
while the fi nal touches are put to a meal. For best results,
pre-heat a covered serving dish for 10 minutes before
adding food to it.
For best results, pre-heat a covered serving dish for 10
minutes before adding food to it.
Use only heat resistant dishes.
Turn it further to use the inner ring as a normal hob plate.
5
9
Although the ceramic surface is very strong, a heavy or
sharp falling object (a salt cellar for example) might cause
the surface to crack. If you fi nd a crack in the surface
immediately disconnect the appliance from the supply
and arrange for its repair.
Care should be taken that no water seeps into the
appliance.
10
The areas marked with two concentric circles have
an inner and an outer element. Turn the control knob
clockwise to heat the whole area for larger pans - turn it
the other way to just heat the inner part for smaller pans.
11
Never cook directly on the surface.
The kind of pan you use and the quantity of food
aff ects the setting required. Higher settings are
required for larger quantities of food.
Naturally, the surface must be washed after use in
order to prevent it from becoming scratched or dirty.
When cooking on the hob you may see the hob area
you are using switch off and on. This is caused by a
safety device that limits the temperature of the hob.
It is quite normal, especially when cooking at high
temperatures. If it happens a lot with a particular
pan however it may mean the pan is not suitable
– perhaps too small or too uneven - for a ceramic hob.
Sugar spillage will permanently damage the hob and
therefore must be cleaned off with care immediately.
Never let sugar spillage cool before trying to remove
it.
If sugar or foods with high sugar content, aluminium
foil or plastic items are accidentally allowed to melt
on the hob surface remove them immediately from
the hot cooking area using a scraper to avoid any
possible damage to the surface. See ‘Cleaning your
cooker’.
Never cut directly on the cooking surface.
Don’t cook directly on the hob surface i.e. without a
pan or utensil
Don’t use the hob as a work surface
Don’t drag or slide utensils across the hob surface
Don’t place anything between the base of the pan
and the hob surface (i.e. asbestos mats, aluminium
foil, Wok stand)
Don’t leave utensils, foodstuff s or combustible items
on the hob when it is not in use. (e.g. tea towels,
frying pans containing oil)
Don’t place plastic or aluminium foil, or plastic
containers on the hob
Don’t leave the hob zones switched on unless being
used for cooking
Don’t place large preserving pans or fi sh kettles
across two heating zones
Don’t place utensils partly covering a heating zone.
Always place utensils centrally.
Never allow anyone to climb or stand on the hob.
6
The Ovens
During use the appliance becomes hot. Care should be taken to avoid the touching heating elements inside
the oven.
Before using for the first time, to dispel manufacturing odours turn the ovens to 240°C and run for an hour.
To clear the smell make sure the room is well ventilated to the outside air, by opening windows for example.
The clock must be set to the time of day before the Multifunction oven will work. See ‘The Clock’ section for
instructions on setting the time of day.
The Left Hand Oven The Right Hand Oven
The left hand oven is a Multi-function oven. As well as
the oven fan and fan element, it is fi tted with two extra
heating elements, one visible in the top of the oven
and the second under the oven base. Take care to avoid
touching the top element and element defl ector when
placing or removing items from the oven. For more
detail on this oven see the section ‘Multi-function oven’.
The fan in the right hand oven circulates hot air
continuously, which means faster more even cooking.
The recommended cooking temperatures for a fanned
oven are generally lower than a non-fanned oven.
The Multi-function oven has two controls, a function
selector and a temperature setting knob.
The right hand fan oven control is at the right hand end
of the control panel.
Turn the function selector control to a cooking function.
This is the fan oven setting.
Turn the oven temperature knob to the temperature
you need.
The oven indicator light will glow until the oven has
reached the temperature you selected. It will then cycle
on and off during cooking.
Turn the oven temperature knob to the temperature
you need.
The oven indicator light will glow until the oven has
reached the temperature you selected. It will then cycle
on and off during cooking.
7
The Clock
You can use the timer to turn the left hand
Multifunction oven on and off . The clock must be set
to the time of day before the left hand Multifunction
oven will work.
To set the time of day
Press and hold as above. At the same time, press (-) or
(+) until the correct time shows. Don’t forget it’s a 24
hour clock. If you make a mistake or press the wrong
button, turn off the power supply for a minute or two
and start again.
To time something that’s cooking
(minute minder)
Press and hold the
Minute Minder (
).
At the same time press
(-) or (+) until the time
you want to cook for is
shown.
You can check time remaining by pressing and
cancel the beeper by pressing
To stop automatically
Use when you have started the oven manually.
Press and hold the Stop
Time (
) button.
At the same time press (-) or (+) until your required
‘Stop Time’ shows. AUTO will show in the display. When
your cooking is fi nished the beeper sounds. TURN THE
OVEN KNOB TO 0 FIRST, then press
once to stop the
beep, press
again to return to manual cooking.
To start and stop the oven
automatically
Before you set the clock, you must have two numbers
clearly in mind.
The ‘cook period’, which is the period of time you
want the oven to cook.
The ‘stop time’, which is the time of day you want the
oven to stop cooking.
You cannot set a start time directly - this is set
automatically by setting the cooking period and stop
time.
Press and hold the Cook
Time (
) button. At
the same time press (-)
or (+) until your required
‘cook period’ shows.
Press and hold the Stop
Time ( ) button.
At the same time press
(-) or (+) until your
required ‘stop time’
shows.
AUTO will show in the
display.
Set the oven to the required temperature. When
your cooking is fi nished the beeper sounds. TURN
THE OVEN KNOB TO 0 (off ) FIRST, then press
once
to stop the beep, press
again to return to manual
cooking.
If you are out, don’t worry about the beeper going
off , it stops after a while. When you return, TURN THE
OVEN KNOB TO 0 (off ) FIRST, then press
twice, to
return to manual cooking.
AUTO is showing, you want to reset to
manual cooking.
When cancelling an automatic setting, any cooking
time already set must be returned to 0.00 before you
can return to manual, by pressing the
button.
Clock Special Features
Key Lock
When the key lock is activated, the clock can be
operated as usual but the oven is locked and will not
come on. This means that your child could select a
cook program but the program will not be activated
and oven will not be switched on.
8
To activate the key lock
Make sure that the clock is in manual mode and
cancel any active programs.
Hold the
Minute Minder (
) and
Cooktime ( ) buttons
for about 8 seconds.
‘On’ will appear on the
display.
Press the ‘+’ button
once.
The key symbol (
) and
‘Of’ will appear on the
display. Let go of the
buttons.
The clock oven control
functions are now
locked.
After a few seconds the
display will revert to
show the time of day
and the key symbol (
).
To turn off the key lock
Hold the
Minute Minder (
) and
Cooktime ( ) buttons
for about 8 seconds.
‘Of’ will appear on the
display.
Press the ‘+’ button
once. The key symbol ( )
goes out and ‘On’ shows
on the display. Let go of
the buttons
After a few seconds the display will revert to show the
time of day.
The oven and the clock oven control functions can
now be used normally.
Cooking using the timer
The timer can control the Multifunction oven only.
You can set the oven to turn on any time over the
following 24 hour period
If you want to cook more than one dish, choose
dishes that require approximately the same time.
However, dishes can be ‘slowed down’ slightly by
using small containers and covering them with
aluminium foil, or ‘speeded up’ slightly by cooking
smaller quantities or placing in larger containers.
Very perishable foods such as pork or fi sh should be
avoided if a long delay period is planned, especially in
hot weather.
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
Avoid using wine or beer if there is a delay period, as
fermentation may take place.
To avoid curdling, cream should be added to dishes
just before serving.
Fresh vegetables, which may discolour during a delay
period, should be coated in melted fat or immersed in
a water and lemon juice solution.
Many frozen foods are ideal for delayed cooking
and can be placed in the oven while still frozen.
Fruit pies, custard tarts or similar wet mixtures on top
of uncooked pastry are only satisfactory if there is a
short delay period. Dishes containing leftover cooked
meat or poultry should not be cooked automatically
if there is a delay period.
Whole poultry must be thoroughly defrosted before
placing in the oven.
Check that meat and poultry are fully cooked
before serving.
Both Ovens
Before using for the fi rst time, to dispel
manufacturing odours turn the ovens to 240°C
and run for an hour. To clear the smell make sure
the room is well ventilated to the outside air, by
opening windows for example.
The wire shelves should always be pushed fi rmly to
the back of the oven.
Baking trays meat tins etcetera should be placed
level centrally on the oven’s wire shelves. Keep all
trays and containers away from the sides of the
oven, as overbrowning of the food may occur.
9
For even browning, the maximum recommended size
for a baking tray is 330mm by 290mm.
Cooking high moisture content foods can create a
‘steam burst’, when the oven door is opened. When
opening the oven stand well back and allow any
steam to disperse.
When the oven is on, don’t leave the door open for
longer than necessary, otherwise the knobs may get
very hot.
• Always leave a ‘fi ngers width’ between dishes on
the same shelf. This allows the heat to circulate
freely around them.
• The Cook & Clean oven liners (see Cleaning your
cooker) work better when fat splashes are avoided.
Cover meat when cooking.
• To reduce fat splashing when you add vegetables
to hot fat around a roast, dry them thor ough ly or
brush lightly with cooking oil.
• If you want to brown the base of a pastry dish,
preheat a baking tray for 15 minutes before placing
the dish in the centre of the tray.
• Where dishes may boil and spill over during
cooking, place them on a baking tray.
Multi-function oven
The left hand oven of your cooker is Multi-function.
It has many varied uses. We sug gest you keep a
careful eye on your cooking until you are familiar with
each function. Remember - not all functions will be
suitable for all food types.
Please remember that all cookers vary - temperatures
in your new ovens may diff er to those in your
previous cooker.
Multi-function oven functions
Defrost
This function operates the fan to circulate cold
air only. No heat is applied. This enables small items
such as desserts, cream cakes and pieces of meat, fi sh
and poultry to be defrosted.
Defrosting in this way speeds up the process and
protects the food from fl ies. Pieces of meat, fi sh and
poultry should be placed on a rack, over a tray to
catch any drips. Be sure to wash the rack and tray
after defrosting.
Defrost with the oven door closed.
Large items, such as whole chickens and joints should
not be defrosted in this way. We recommend this be
carried out in a refrigerator.
Defrosting should not be carried out in a warm oven
or when an adjoining oven is in use or still warm.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
10
Fan oven
This function operates the fan and the heating
element around it. An even heat is produced
throughout the oven, allowing you to cook large
amounts quickly.
Fan oven cooking is particularly suitable for baking
on several shelves at one time and is a good ‘allround’ function. It may be necessary to reduce the
temperature by approximately 10°C for recipes
previously cooked in a conventional oven.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the food.
Fanned grilling
This function operates the fan whilst the top
element is on. It produces a more even, less fi erce
heat than a conventional grill. The supplied pan can
used either on an oven shelf or on the Handygrill rack
(see the Handygrill section of the instructions) The
pan is designed to allow air circulation. Thick pieces
of meat or fi sh are ideal for grilling in this way, as the
circulated air reduces the fi erceness of the heat from
the grill. The oven door should be kept closed whilst
grilling is in progress, so saving energy. You will also
fi nd that the food needs to be watched and turned
less than for normal grilling. Pre-heat this function
before cooking.
Fan assisted oven
This function operates the fan, circulating air
heated by the elements at the top and the base of
the oven. The combination of fan and conventional
cooking (top and base heat) makes this function ideal
for cooking large items that need thorough cooking,
such as a large meat roast. It is also possible to bake
on two shelves at one time, although they will need
to be swapped over during the cooking time, as the
heat at the top of the oven is greater than at the base,
when using this function.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to this function.
Conventional oven
(top and base heat)
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits. Food cooked
on the top shelf will brown and crisp faster than on
the lower shelf, because the heat is greater at the top
of the oven than at the base, as in ‘Fan assisted oven’
function. Similar items being cooked will need to be
swapped around for even cooking. This means that
foods requiring diff erent temperatures can be cooked
together, using the cooler zone in the lower half of
the oven and hotter area to the top.
Browning element
This function uses the element in the top of
the oven only. It is a useful function for the browning
or fi nishing of pasta dishes, vegetables in sauce,
shepherds pie and lasagne, the item to be browned
being already hot before switching to the top
element.
Base heat
This function uses the base element only. It
will crisp up your pizza or quiche base or fi nish off
cooking the base of a pastry case on a lower shelf.
It is also a gentle heat, good for slow cooking of
casseroles in the middle of the oven or for plate
warming.
The Browning and Base heat functions are useful
additions to your oven, giving you fl ex i bil i ty to fi nish
off items to perfection. With use, you will soon realise
how these functions can com bine to extend your
cooking skills.
11
The Handygrill
The maximum weight than can be held by the
Handygrill is 5.5kg (12lb). It should only be used
with the supplied tin, which is designed to fi t the
rack. Any other vessel could be unstable.
The Handygrill fi ts on the oven door. Food cooking on
it is easy to attend to, because it’s accessible when the
door is opened. It can be fi tted at diff erent heights.
Depending on the height that it is fi xed, the oven
shelves may need to be removed or repositioned to
suit.
Using your Handygrill
Fan Grilling
Fanned grilling is carried out with the oven door
closed.
The racking on the inside of the Multifunction Oven
door (left hand oven) allows you to position the
Handygrill at any of four diff erent levels.
Using the Handygrill for fan grilling gives you the
ability to tend the food without having to lift the grill
pan out of the oven.
It is important to remember to clean the grill pan
after each grilling session, as a build up of fat would
dangerous and unhygienic.
Be careful when opening and closing the oven door
whilst using the Handygrill.
Grilling Cooking Chart
The position of the Handygrill on the oven door
brackets will depend upon the size of the food being
grilled.
Pre-heat the oven on the fanned grilling function
with the oven door closed for 5-10 minutes before
use.
Always decide on the level at which to grill before
the preheating period as the Handygrill rack and pan
will get very hot.
The second level from the top is the most useful for
normal grilling. Only use the top position for toast or
very quick cook items such as minute steak.
These timings are recommendations only
Food Temperature Cooking Time Minutes
Sausages 200-Max 5-10 per side
Bacon 200-Max 5-7 per side
Burgers 200-Max 5-10 per side
Chop or Steak 200-Max 10-15 per side
Chicken Portion 200-Max 10-15 per side
Salmon Steak 200-Max 10-15
Other uses
The Handygrill and pan can also be used for roasting.
Remove the trivet from the pan and position the rack
at the height of the centre of the oven. Use the fan
or conventional oven settings and follow the guide
time in the cooking chart for roasting. Only use the
supplied pan in the Handygrill rack - any other vessel
could be unstable.
To fit the Handygrill
Line up the ends of the Handygrill rack with a pair of
holes in the mounting brackets on the oven door.
left hand side right hand side
Slide the ends into both uprights at the same time.
left hand side right hand side
Hook the rack on to the uprights.
12
Oven shelves
the shelf guard should be at the back pointing upwards
As well as the fl at shelves some models are supplied
with a drop shelf. The drop shelf increases the
possibilities for oven shelf spacing.
The oven shelves can be easily removed and refi tted.
Pull the shelf forward
until the back of the shelf
is stopped by the shelf
stop bumps in the oven
sides.
Lift up the front of the
shelf so the back of the
shelf will pass under the
shelf stop and then pull
the shelf forward.
To re fi t the shelf, line up the shelf with a groove in the
oven side and push the shelf back until the ends hit
the shelf stop. Lift up the front so the shelf ends clear
the shelf stops, and then lower the front so that the
shelf is level and push it fully back.
Steam
When cooking foods with high water content (e.g.
oven chips) there may be some steam visible at the
grille at the rear of the hotplate. This is perfectly
normal.
Oven light
Press the appropriate button to turn on the oven
light.
If the oven light fails, turn off the power
supply before you change the bulb. See the
‘Troubleshooting’ section for details on how to
change an oven light bulb.
Storage
The drawer can get very warm, don’t store anything
in it that may melt or catch fi re.
The drawer can be removed completely for cleaning
etc.
To remove the drawer pull it forward.
13
Lift up the ends of the plastic clips (one each side) to release the catches holding the drawer to the side runners and
at the same time pull the drawer forward and away from the side runners.
For safety’s sake push the drawer runners back out of the way.
To refit the draw
Rest the drawer back on the side runners and, keeping it level, push it right back. The clips should click into position
holding the drawer to the side runners.
14
Multi-function Oven cooking guide
Remember - not all functions will be suitable for all food types. The oven control settings and cooking times
given are intended to be used only as a guide. Individual tastes may require the temperature to be altered to
provide a preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce
the temperature by 10°C and the cooking time by 5-10 min utes. The temperature in the fanned oven does not
vary with height in the oven - so you can use any shelf.
The shelves should not be fi tted directly one above the other. When cooking on more than one shelf always
leave at least one runner space between them. Place baking trays, individual cake tins or baking dishes
centrally on the oven shelf. For best results pre-heat the oven until the oven indicator light goes out.
Cooking chart - Fan assisted oven function
Food Te mp
Oven Shelf
Position Approximate Cooking Time
Fairy cake 170°C 2-4 20 min
Scone 180°C 2-4 15 min
Deep apple pie 160°C 2-4 45 min interchange after 25 minutes
Plate tart 190°C 2-4 45 min interchange After 25 minutes
Rich fruit cake 197mm x 92mm 145°C 3 1 hr 45 min - 2 hr
Victoria sandwich 180mm 170°C 2-4 20 - 25 min
Milk pudding 150°C 3 2 hrs
Puff pastry 220°C 3 - 5 15-40 mins according to size. Interchange 2/3rds
through cook ing time
For roast meats and poultry refer to the Fan oven guide - reduce cooking time slightly.
500g is approximately 1lb (1lb 2oz)
Ensure meat and poultry is fully cooked before serving
15
Cooking chart - Conventional and full Fan oven functions
Convection Oven Fan Oven
Food Temperature
Shelf
Position
Temperature Approximate Cooking Time
FISH
190°C 3 180°C Fillets 15-20mins.
190°C 3 180°C Whole 10mins.per 500g + 10mins.
190°C 3 180°C Steaks according to thickness.
ROAST MEATS
Beef with bone 160°C 2-3 150°C 20-25mins. per 500g + 20-25mins.
200°C 2-3 190°C 15-20mins. per 500g + 15-20mins.
Beef without bone 160°C 2-3 150°C 30-35mins. per 500g + 30-35mins.
200°C 2-3 190°C 20-25mins. per 500g + 20-25mins.
Lamb 160°C 2-3 170°C 30-35mins. per 500g + 30-35mins.
200°C 2-3 190°C 25-35mins. per 500g + 25-30mins.
Pork 160°C 2-3 150°C 35-40mins. per 500g + 35-40mins.
200°C 2-3 190°C 25-30mins. per 500g + 25-30mins.
Stuff ed and rolled - Add approx. 10 mins. per 500g to above cooking times or cook at 200°C for 20mins. then 160°C for
remainder.
THOROUGHLY THAW FROZEN JOINTS AND POULTRY BEFORE COOKING.
POULTRY
Chicken 160°C 2-3 150°C 20-25mins. per 500g + 20-25mins.
200°C 2-3 190°C 15-20mins. per 500g + 15-20mins.
Turkey 160°C 2 150°C 20-25mins. per 500g + 20-25mins.
200°C 2 190°C 15-20mins. per 500g + 15-20mins.
Stuff ed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for remainder. Prepacked (fresh or frozen) follow
packers cooking times
CASSEROLE 140-150°C 2-3 140°C 2-4hrs according to recipe
YORKSHIRE PUDDING 220°C 4 200°C Large tin 30-35mins. Individual 10-20mins.
CAKES
Very Rich Fruit 140°C 2 140°C 45-50mins. per 500g mixture
Rich fruit (180mm) 150°C 2 145°C 2
1
/2-3hrs.
Madeira (180mm) 160°C 2 150°C 80-90mins.
Queen Cakes 190°C 3 & 5 or 3 180°C 15-25mins.
Scones 220°C 2 & 4 or 3 210°C 10-15mins.
Victoria Sandwich 180°C 2 & 4 or 3 170°C 20-30mins.
PASTRIES
Plate Tart 200°C 2 & 4 190°C 45-50mins. Interchange after 25mins.
Fruit Pie 200°C 2 & 4 190°C 35-40mins.
Tartlets 200°C 4 190°C 15-20mins. according to size.
Puff Pastry 220°C 2,3 or 4 200°C 20-40mins. according to size.
BREAD 220°C 2 & 4 200°C 20-30mins.
MERINGUES 110°C 3 100°C 2-2
1
/2hrs
PUDDINGS
Baked Egg Custard 160°C 3 150°C 45mins.-1hr.
Baked sponge pudding 190°C 3 180°C 40-45mins.
Milk pudding 140-150°C 3 150°C 2-3hrs.
16
Cleaning your cooker
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity supply
before use.
Never use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine
based bleach cleaners, coarse abrasives or salt.
Don’t mix diff erent cleaning products - they
may react together with hazardous results.
Recommended cleaning materials are shown in
the table at the end of this section.
If you want to move your cooker for cleaning, see the
section called ‘Moving your cooker’.
All parts of the cooker can be cleaned with hot soapy
water - but take care that no surplus water seeps
into the appliance.
For cleaning materials see the ‘Cleaning Table’ at the
end of this section.
Hob
It’s very easy to clean the Hob with a recommended
cleaner.
CAUTION — Do not use abrasive cleaners or pads,
oven aerosols or pads or stain removers on the
surface.
Daily care
First of all, be sure that all heat indicator lights are off
and the cooking surface is cool. Apply a small dab,
about the size of a 10p piece, of ceramic cooking
cleaning cream in the centre of each area to be
cleaned. Dampen a clean paper towel and work the
cleaning cream on the cooking surface as if you were
cleaning a window. As a fi nal step, wipe the cooking
surface with a clean, dry paper towel.
Cleaning for spills
For spills and boil-overs that occur while cooking,
turn the unit off and wipe the area surrounding the
hot zone with a clean paper towel. If a spill (other
than a sugary substance) is on the hot zone, do
not clean until the unit is completely cooled down
and follow the instructions below (“Cleaning for
burned-on spills”). If you accidentally melt anything
on the cooking or if you spill foods with a high sugar
content (preserves, tomato sauce, etc.), REMOVE the
spill IMMEDIATELY with a razor scraper, while the
unit is still hot. IMPORTANT: Use an oven glove to
protect your hand from potential burns. Scrape the
major spill or melted material from the cooking zone
and push into a cold area. Then, turn the unit “OFF”
and allow to cool before cleaning further. After the
cooking surface cools down and the heat indicator
lights go off , use the daily care procedure as outlined
above.
Cleaning for burned-on spills
Be sure that the heat indicator lights are off and the
hob is cool. Remove excess burned-on substance
with a single-edged razor scraper. Hold the scraper at
approximately a 30° angle to the surface and scrape
off the burned-on matter as you would scrape paint
off of a window.
IMPORTANT: Take care when using a sharp scraper.
When you have removed as much as possible with
the scraper clean using the daily care procedure as
described above.
To remove metal rub-off
Sliding pans on the hob - especially aluminium or
copper pans can leave marks on the surface. These
marks often appear like scratches, but can be easily
removed using the procedure described above for
cleaning spills. If the rub-off marks are especially
stubborn, use the cleaning cream together with the
razor scraper, using the technique described above.
Handygrill
The pan and grid should be washed in hot soapy
water. After grilling meats or any foods that soil, leave
to soak for a few minutes in the sink immediately
after use. Stubborn particles may be removed from
the grid by using a nylon brush.
Control Panel and Doors
Avoid using any abrasive cleaners including cream
cleaners, e.g. Cif, on brushed Stainless Steel surfaces.
For best results use a liquid detergent e.g. Domestos
Multi Surface Cleaner.
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean hot
soapy water. Wipe with a clean dampened cloth then
polish with a dry cloth. The oven doors should only
be cleaned with a soft cloth wrung out in clean hot
soapy water.
17
Cleaning Table
Hobplate
Part Finish Recommended Cleaning Method
Ceramic Hob Glass with anodised
aluminium surround.
Remove any dried baked on food deposits with a ceramic hob scraper from
the glass, available from electrical retailers i.e. Curry’s. Clean with HobBrite
Homecare Products or Easy-Do Hobcare Ceramic and Halogen Hob Cleaner
and Conditioner Easy-Do Products Ltd (Curry’s) and polish with a soft cloth.
Do not use cleaners intended for the ceramic hob on the hob surround.
Only use hot soapy water and a soft cloth on the surround.
Outside of cooker
Part Finish Recommended Cleaning Method
Door, Door surround and Storage
Drawer exterior.
Enamel or paint Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless Steel E Cloth (Comet) or Vileda Microfi bre Plus All Purpose Cloth
Freudenberg Household Products LP (supermarket)
Sides and Plinth Painted surface Hot soapy water, soft cloth.
Splashback/Rear Grille Enamel or Stainless
Steel
Hot soapy water, soft cloth. Cream cleaner, with care, if
necessary.
Control panel Paint, Enamel or
Stainless Steel
Warm soapy water. Do not use abrasive cleaners on lettering.
Control Knobs/Handles Plastic/ Chrome Warm soapy water, soft cloth.
Oven Door Glass/Glass Lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Ovens
Part Finish Recommended Cleaning Method
Sides, fl oor & roof of oven NOT COOK & CLEAN OVEN PANELS
(see below)
Enamel Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS FOLLOW MANUFACTURERS INSTRUCTIONS. Do not allow
contact with the oven elements.
Cook & Clean Oven Panels (some
models only)
Special enamel
that partly cleans
itself
This surface cleans itself at 200°C and above, or the panels
can be removed and washed with hot soapy water and a
nylon brush. (see ‘The Ovens’ in ‘Cleaning your cooker’)
Oven Shelves, Handyrack, Grill
Trivet, Handygrill rack
Chrome An oven interior cleaner that is suitable for chrome. Soap
fi lled pad. Dishwasher.
Grill Pan/Meat Tin, Handygrill Pan
(some models only)
Enamel Hot soapy water. Soap fi lled pad (Brillo). Dishwasher.
Cleaners listed are available from Supermarkets or
electrical retailers as stated. Cleaner manufacturerin
Italics
For enameled surfaces use a cleaner that is approved for
use on vitreous enamel. The vitreous enamel association
has a list of approved cleaners. Contact them via their
website www.ive.org.uk or telephone: 01527 893031.
Regular cleaning is recommended. For easier
cleaning, wipe up any spillages immediately.
To help keep your oven clean, cover meat when
roasting, with foil or use a roasting bag. Brush
vegetables with fat before placing around the
meat.
18
Ovens
The ovens have removable panels that have been
coated with a special enamel that partly cleans itself.
This does not stop all marks on the lining, but helps
to reduce the amount of manual cleaning needed.
The Cook & Clean panels work better above
200°C. If you do most of your cooking below this
temperature, occasionally remove the panels and
wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and
the oven heated at 200°C for about one hour. This
will ensure the Cook & Clean panels are working
eff ectively.
Don’t use steel wool (Brillo) or any other materials
that will scratch the surface. Don’t use oven cleaning
pads.
Removing the Oven Linings
Some of the lining panels can be removed for
cleaning and for cleaning behind. Remove the
shelves fi rst.
The side panels of either oven can be removed.
Each side of the oven is fi xed with four fi xing screws.
You don’t have to remove the screws to remove the
oven linings. Lift each side panel upwards and they
will slide off the screws. Then pull them forwards.
Once the linings are removed, the oven enamel
interior can be cleaned.
Troubleshooting
A crack has appeared in the Hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Don’t use the cooker
until after the repair. See the Customer care leafl et for
how to contact a service person.
My Hob is scratched
Have you used the correct cleaning methods?
Pots and pans with rough bottoms, or coarse particles
(salt or sand) between the pan and the surface of the
hob may cause scratches.
Use the recommended cleaning methods. Make sure
pan bottoms are smooth and clean. Tiny scratches are
not removable but will become less visible in time as
a result of cleaning.
Metal markings on the Hob
Do not slide aluminium or copper pans across the
surface. Marks from aluminium and copper pans as
well as mineral deposits from water or food can be
removed with the cleaning cream.
Steam is coming from the oven
When cooking foods with a high water content (e.g.
oven chips) there may be some steam visible at the
rear grille. Take care when opening the oven door, as
there may be a momentary puff of steam when the
oven door is opened. Stand well back and allow any
steam to disperse.
The oven fan is noisy
The note of the oven fan may change as the oven
heats up - this is perfectly normal.
What cleaning materials are recommended for the
cooker?
See the ‘Cleaning’ section for recommended cleaning
materials. We do not recommend Mr. Muscle, as it
contains chemicals that may damage the surfaces of
your cooker.
The knobs get hot when I use the ovens, can I avoid
this?
Yes, this is caused by heat rising from the oven and
heating them up. Don’t leave the oven door open.
If there is an installation problem and I don’t get my
original installer to come back to fix it who pays?
You do. Service organisations will charge for their callouts if they are correcting work carried out by your
original installer. It’s in your interest to track down
your original installer.
19
Current Operated Earth Leakage Breakers
Where the cooker installation is protected by a
30 milliamp sensitivity residual current device (RCD),
the combined use of your cooker and other domestic
appliances may occasionally cause nuisance tripping.
In these instances the cooker circuit may need to be
protected by fi tting 100mA device. This work should
be carried out by a qualifi ed electrician.
Food is cooking too slowly, too quickly, or burning
Cooking times may diff er from your previous
oven. Check that you are using the recommended
temperatures and shelf positions. See the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
Individual tastes may require the temperature to be
altered either way, to get the results you want. Try
cooking at a higher temperature setting.
The oven is not cooking evenly
Do not use a tin or baking tray larger than 330mm x
290mm.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been
left for the heat to cir cu late. When a baking tray is put
into the oven, make sure it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held fi rmly
against the seal.
A dish of water when placed on the shelf should be
the same depth all over. (For example, if it is deeper
at the back, then the back of the cooker should be
raised up or the front lowered). If the cooker is not
level arrange for your supplier to level it for you.
The left hand Multi-function oven not coming on
when turned on manually
Is the power on? Is the clock illuminated?
If not there may be something wrong with the power
supply. Is the cooker supply on at the isolator switch?
Has the time of day been set?
Have you set a cooking function?
Is the key symbol (
) showing in the display? See the
Clock section of the instructions for more information
on the key lock feature of the clock.
The left hand Multi-function oven not coming on
when automatic cooking
Timer set correctly but oven knob left OFF by
mistake?
Is the key symbol (
) showing in the display? See the
Clock section of the instructions for more information
on the key lock feature of the clock.
Have you set a cooking function?
Oven temperature getting hotter as the cooker gets
older
If turning the knob down has not worked or only
worked for a short time then you may need a new
thermostat. This should be fi tted by a service person.
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from a good electrical shop. Ask for an
Edison screw fi tting 15w 240v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300 °C. See
the HELP leafl et for spares by mail order.
Turn off the power supply.
Make sure the oven is cool. Open the oven door and
remove the oven shelves.
Unscrew the bulb cover by turning anticlockwise. It
may be very stiff .
Taking care to protect your fi ngers in case the bulb
should shatter, unscrew the old bulb.
Screw in the new bulb, screw back the bulb cover.
Turn on the electricity supply and check that the bulb
now lights.
20
General Safety Instructions
The cooker must be installed by a qualifi ed electrician
in accordance with the installation instructions. It
should be serviced by a qualifi ed service engineer
and only approved spare parts used. Have the
installer show you the location of the cooker control
switch. Mark it for easy reference. Always allow the
cooker to cool and then switch off at the mains and
before cleaning or carrying out any maintenance
work, unless specifi ed otherwise in this guide.
All parts of the cooker become hot with use and
will retain heat even after you have stopped
cooking.
Take care when touching the hob especially the
marked cooking areas. The glass surface of the hob
will retain heat after the controls have been turned
off . To minimize the possibility of burns, always be
certain that the hob controls are in the OFF position
and that the entire glass surface is cool before
attempting to clean the hob.
Use dry oven gloves when applicable - using damp
gloves might result in steam burns when you touch
a hot surface. Never operate the cooker with wet
hands.
Do not use a towel or other bulky cloth in place of
a glove. They might catch fi re if they touch a hot
surface.
Always turn the surface unit controls off before
removing the pans.
Don’t place utensils on the hob surface when it is in
use. They may become hot and could cause burns.
Clean the hob with caution. If a wet sponge or
cloth is used to wipe spills on a hot surface unit, be
careful to avoid steam burns. Some cleansers can
produce noxious fumes if applied to a hot surface.
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
Babies, toddlers and young children should not be
allowed near the cooker at any time. They should
never be allowed to sit or stand on any part of the
appliance. Teach them not to play with controls or
any other part of the cooker.
Never store anything of interest to children in
cabinets above a cooker - children climbing on the
cooker to reach them could be seriously injured.
Clean only parts listed in this guide.
In the interests of hygiene and safety the cooker
should be kept clean at all times as a build up in fats
and other food stuff could result in a fi re.
We recommend that you avoid wiping any surface
unit areas until they have cooled and the indicator
light has gone off . Sugar spills are the exception to
this. Please see ‘Cleaning your cooker’. When the
hob is cool, use only the recommended cleaning
cream to clean the hob.
To avoid possible damage to the cooking surface,
do not apply the cleaning cream to the glass surface
when it is hot. Read and follow all instructions
and warnings on the cleaning cream labels. After
cleaning, use a dry cloth or paper towel to remove
any cleaning cream residue.
Avoid heating an empty pan. Doing so may
damage the hob and the pan.
Always keep combustible wall coverings or curtains
etc. a safe distance away from your cooker.
Do not place or store items on top of the glass hob
surface when it is not in use.
Do not spray aerosols in the vicinity of the cooker
while it is in on.
Do not store or use combustible materials, or
fl ammable liquids in the vicinity of this appliance.
Do not use water on grease fi res. Never pick up a
fl aming pan. Turn the controls off . Smother a fl aming
pan on a surface unit by covering the pan completely
with a well fi tting lid or baking tray. If available
use a multipurpose dry chemical or foam-type fi re
extinguisher.
Never leave the hob unattended at high heat
settings. Pans boiling over can cause smoking and
greasy spills may catch on fi re.
Never wear loose-fi tting or hanging clothes while
using the appliance. Be careful when reaching for
items stored in cabinets over the hob. Flammable
material could be ignited if brought in contact with a
hot surface unit and may cause severe burns.
Take great care when heating fats and oils, as they
will ignite if they get too hot.
Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
21
Never leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If
you use a combination of oils or fats in frying, stir
them together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost
on frozen foods or moisture on fresh foods can cause
hot fat to bubble up and over the sides of the pan.
Carefully watch for spills or overheating of foods
when frying at high or medium high temperatures.
Never try to move a pan of hot fat, especially a deep
fat fryer. Wait until the fat is cool.
When the ovens are on, do not use the top of
the fl ue (the slot along the back of the cooker)
for warming plates, dishes, drying tea towels or
softening butter.
When using an electrical appliance near the hob, be
sure that the cord of the appliance does not come
into contact with the surface area.
If you fi nd a crack in the hob surface immediately
disconnect the appliance from the supply and
arrange for its repair.
Take care that no water seeps into the appliance
Only certain types of glass, glass-ceramic,
earthenware or other glazed containers are
suitable for hob cooking; others may break
because of the sudden change in temperature.
Use proper pan size-select pans having fl at bottoms
large enough to cover the surface unit’s heating area.
The use of undersized pans will expose a portion of
the surface unit to direct contact and may result in
ignition of clothing. Proper relationship of pans to
surface unit will also improve effi ciency.
Do not allow anyone to climb, stand or hang on
any part of the cooker.
Do not use aluminium foil to cover shelves, linings or
the oven roof.
Make sure that your kitchen is well ventilated at all
times. Use extractor fans or hoods when fi tted.
Never heat unopened food containers. Pressure build
up may make container burst and cause injury.
The cooker is designed for cooking foods only and
must not be used for any other purpose.
The oven should NOT be used for heating the kitchen,
not only does this waste fuel but the control knobs
may become overheated.
When the oven is on DO NOT leave the oven door
open for longer than necessary.
The specifi cation of this cooker should not be altered.
This appliance is heavy, take care when moving it.
When the cooker is not in use ensure that the control
knobs are in the off position.
Do not slide pans across the hob because this can
scratch the glass - the glass is scratch resistant, not
scratch proof. Sharp instruments, rings or other
jewellery and rivets on clothing could scratch the
hob surface.
Do not use the surface as a cutting board.
Don’t store heavy items above the hob. If they drop
on the hob, they could cause damage.
22
INSTALLATION
Check the ap pli ance is electrically safe when you have fi nished.
Dear Installer
Before you start your installation, please complete the details BELOW.
If your customer has a problem relating to your installation they will be able to
contact you easily.
Thank you
Installer’s Name
Installer’s Company
Installer’s Telephone number
Installation
Regulations
This appliance must be installed by a qualifi ed electrician to comply with the
relevant regulations and also the local electricity supply company requirements.
You will need the following equipment to complete the cooker installation
satisfactorily
Multimeter (for electrical checks)
Steel tape measure
Cross head screwdriver
Spirit level
Cooker levelling tool (provided in pack)
23
INSTALLATION
Check the ap pli ance is electrically safe when you have fi nished.
Positioning the Cooker
The diagrams below show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
The hotplate surround should be level with, or above,
any adjacent work surface. Above hotplate level a gap
of 75mm should be left between each side of the cooker
and any adjacent vertical surface.
For non-combustible surfaces (such as unpainted metal
or ceramic tiles) this can be reduced to 25mm.
A minimum space of 650mm is required between the
top of the hotplate and a horizontal combustible surface.
*Any cooker hood should be installed in accordance with
the hood man u fac tur er’s instructions.
Surfaces of furniture and walls at the sides and rear of
the appliance should be heat, splash and steam resistant.
Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage and discolouration.
We cannot accept responsibility for damage caused
by normal use of the cooker to any material that delaminates or discolours at temperatures less than 65°C
above room temperature.
For safety reasons curtains must not be fi tted
im me di ate ly behind the cooker.
We recommend a gap of 1110mm between units to
allow for moving the cooker. Do not box the cooker in; it
must still be possible to move the cooker in and out for
cleaning and servicing.
Checking the parts
Allen key Levelling tool
Handygrill rack Handygrill pan / Meat tin
3 fl at oven shelves and 1 drop
shelf
Plinth
A clearance of 130mm is required if the cooker is near a
corner of the kitchen to allow the oven doors to open.
The actual opening of the doors is slightly less but this
allows for some protection of your hand as you open the
door.
Plan view
A clearance of 130mm each side is required to allow for oven
door opening.
Unpacking the Cooker
Do not take any packaging off the cooker until it is
directly in front of the place it is to be installed (unless it
will not fi t through a door in its outer packaging).
Cut the banding straps and lift the cardboard box off
the cooker, leaving the cooker standing on the base
packaging. See the loose unpacking sheet.
Moving the Cooker
The cooker is very heavy. Take great care.
We recommend two people manoeuvre the cooker.
Ensure that the fl oor covering is fi rmly fi xed, or removed
to prevent it being disturbed when moving the cooker
around. You will need the levelling tool.
24
INSTALLATION
Check the ap pli ance is electrically safe when you have fi nished.
From the back tilt the cooker forward and remove the
rear half of the polystyrene base pack.
Repeat from the front and remove the front half of the
poly base. Pull the drawer out to its furthest point.
Lift up the ends of the plastic clips (one each side) to
release the catches holding the drawer to the side
runners and at the same time pull the drawer forward
and away from the side runners. For safety’s sake push
the drawer runners back out of the way. Put the drawer
somewhere safe - do not refi t it until the installation is
complete.
Lower the Rollers.
Fit the Allen key tool to the centre roller lowering
mechanism (C in the fi g. below).
A left rear roller, B right rear roller, C centre roller
LOWER THE FRONT ROLLER by doing 14 complete (360°)
turns clockwise.
Now LOWER THE TWO REAR ROLLERS.
First fi t the levelling tool on the hexagonal adjusting nut
as shown below.
Make 10 complete (360°) turns clockwise. (This means
turning and removing the levelling tool 20 times).
Make sure you lower BOTH REAR ROLLERS. There are
two adjusting nuts, one for each roller, at both the front
bottom corners of the cooker.
Unfold the rear edge of
pack base tray. Carefully
push the cooker backwards
into position. Take care not
to damage the power cable.
Push the cooker close to
its fi nal position, leaving
just enough space to get
behind it.
Levelling
You are recommended to use a spirit level on a shelf in
one of the ovens to check for level.
Place the cooker in its intended position taking care not
to twist it within the gap between the kitchen units as
damage may occur to the cooker or the units.
The rollers can be adjusted to level the cooker. To adjust
the height of the rear of the cooker use the levelling tool
supplied to turn the adjusting nuts at the front bottom
corners of the cooker.
Adjust the height of the front roller to level the cooker.
Turn clockwise to raise the cooker and anticlockwise to
lower.
When you are satisfi ed with the height and level, raise
the front of the cooker by one turn of the front roller
adjuster. Screw down the front feet to meet the fl oor.
Screw the front roller adjuster anticlockwise to raise the
25
INSTALLATION
Check the ap pli ance is electrically safe when you have fi nished.
front roller so that the front of the cooker is supported
on the feet, not the front roller, to prevent accidental
movement of the cooker.
Leave the levelling tool in the storage drawer, so that the
customer can use it if they wish to move the cooker.
Electrical Connection
This appliance must be installed by a qual i fi ed electrician
to comply with the relevant In sti tute of Electrical
Engineers (I.E.E.) regulations and also the local elec tric i ty
supply company re quire ments.
Make sure that the mains characteristics (voltage,
nominal, power, etc.) match the ratings indicated on the
data plate affi xed to the lower right hand cooker upright
(remove storage drawer). The cooker is preset for a
single-phase earthed electrical connection. It is essential
to install a multi-pole circuit breaker that completely
disconnects the appliance from the mains, with a
minimum contact break distance of 3mm.
WARNING: THIS APPLIANCE MUST BE EARTHED
The appliance must be connected to an effi cient
earthing circuit. If the electricity network is not equipped
with an earth connection, then it must be installed
separately in compliance with local regulations. Earthing
is a safety measure required by law, and must be
performed with particular care by a qualifi ed technician,
who must also check that the electricity supply
characteristics are correct.
The cable size used should be suitable for the appliance
load and in accordance with local regulations. Please
note the maximum cable sizes are 6mm2 for the screw
terminals and 10mm2 for the 3 pronged links.
Access to the mains terminal is gained by removing
the electrical terminal cover box on the back panel.
Connect the mains cable to the correct terminals for your
electrical supply type (see fi g.).
Check that the links are correctly fi tted and that
the terminal screws are tight.
Secure the mains cable using the cable clamp.
Current Operated Earth Leakage Breakers
Where the installation is protected by a 30 milliamp
sensitivity residual current device (RCD), the combined
use of your cooker and other domestic appliances may
oc ca sion al ly cause nuisance tripping. In these instances
the cooker circuit may need to be protected by fi tting
100mA device. This work should be carried out by a
qualifi ed electrician.
Oven Light
Press the oven light switch and check that the light is
working.
NB The oven light bulb is not included in the guarantee
Hobplate
Turn on each plate in turn and check that it heats up.
Oven check
The clock must be set to the time of day before the
Multifunction oven will work.
Press and hold as above.
At the same time, press - or + until the correct time
shows.
Don’t forget it’s a 24 hour clock.
If you make a mistake or press the wrong button, turn off
the power supply for a minute or two and start again.
Turn on the ovens. Check that the oven fan starts to turn
and that the oven starts to heat up. Turn off the ovens.
Fitting the plinth
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw.
Twist and fi t each end keyhole over their respective
screws. Tighten the fi xing screws.
Refit the drawer
Rest the drawer back on the side runners and, keeping
it level, push it right back. The clips should click into
position holding the drawer to the side runners
Customer care
Please complete your contact details in the front of
this section. Please inform the user how to operate the
cooker and hand over the instruction pack.
Thank you.
26
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity servicing. Check appliance is safe when you have finished.
Servicing
Disconnect from electricity supply before
commencing servicing, particularly before removing
any of the following: control panel, side panels,
ceramic hob, or any of the electrical components or
cover boxes.
Before electrical re-connection, check that the appliance
is electrically safe.
Note - References to LH and RH oven apply as viewed
from the front.
Contents
1. To Remove a Side Panel 26
2. To Lift up the Ceramic Hob 26
3. To replace a hob element. 26
4 To Remove the Control Panel 26
5. To Remove Oven Light Switch 26
6. To Remove Electronic Timer 27
7. To Change Hob Controller 27
8. To Remove a Thermostat 27
9 To Remove an Oven element Thermal Cut-Out. 27
10. To Remove an Oven Door 27
11. To Change Oven Door Outer Panel 27
12. To Change Oven Door Latch 27
13. To Adjust an Oven Door Catch Keep 28
14. To Change Oven Door Seal 28
15. To Remove Oven Inner Back 28
16. To Replace an Oven Fan 28
17. To Remove an Oven fan Element 28
18. To Remove the LH Oven Bottom and Top Elements 29
1. To Remove a Side Panel
Disconnect from electricity supply.
Pull the cooker forward.
Pull off the push fi t control panel end caps at each end
and remove the end fi xing screws under the end cap.
Remove the retaining screws for each panel (1 at the
front and 2 at the rear). The lower front retaining screws
(one each side) are situated beneath the lower edge at
the front corners of the side panels
Reassemble in reverse order.
2. To Lift up the Ceramic Hob
Pull the cooker forward.
Pull off the push fi t control panel end caps at each end
and remove the end fi xing screws under the end cap.
Remove the lower front retaining screws (one each side)
situated beneath the lower edge at the front corners of
the side panels.
Swing the side panels to gain access to the hob fi xing
screws (1 each side) at the top front of the side uprights.
Remove these screws.
Caution
The ceramic hob material is much more sensitive
to scratches on the underside than the top.
Lift up the ceramic hob at the front and prop in position
with a non-metallic prop.
Take care not to touch or scratch the underside of
the ceramic as this will weaken the material and
cause the top to shatter.
3. To replace a hob element.
Lift up the ceramic hob see 2. The elements are now
accessible.
4 To Remove the Control Panel
Disconnect from electricity supply.
Lift up the front of the ceramic hob – see 2. Remove the
control panel top scews.
Pull off all the control knobs. Open the oven doors and
remove the control panel fi xing screws underneath the
control panel. The screws directly below the clock are
for the clock fi xing bracket - don’t remove them at this
stage.
Lift the control panel, pull forward and disconnect the
wiring from the rear.
Reassemble in reverse order. When replacing leads refer
to the wiring diagram. Check operation of timer.
5. To Remove Oven Light Switch
Remove control panel (see 4).
NB The old switch may be destroyed during removal.
Remove switch button and old switch from its bezel by
gripping the switch body behind the control panel and
twisting sharply.
The switch bezel can then be removed by folding back
its locking wings and pushing forward. Fit the new bezel
27
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
to the control panel by fi rst lining up the raised key on its
body with the cut-out in the control panel and pushing it
in from the front. Assemble the new switch to the bezel
by lining up the key sections and pushing home. Fit the
new button by pushing in from the front.
Replace control panel in reverse order and test for
correct operation.
6. To Remove Electronic Timer
Disconnect from electricity supply.
Pull off the timer control buttons and remove the control
panel (See 4). Remove the timer/mounting bracket
assembly from the control panel by removing the two
fi xing screws. Remove the timer from its mounting
bracket by depressing the plastic lugs on the timer case,
at the same time pulling the unit forward.
Reassemble in reverse order. When replacing leads refer
to the wiring diagram. Check operation of timer
7. To Change Hob Controller
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Disconnect wiring from controller. Remove
2 screws holding controller to mounting panel. Fit new
controller and reassemble in reverse order. Check for
correct operation.
8. To Remove a Thermostat
Disconnect from the electricity supply.
Lift up the ceramic hob top (see 2). Remove control
panel (see 4). Open appropriate oven door and remove
oven furniture.
RH oven
Remove the two fi xings that secure the thermostat phial
cover. Unclip the thermostat phial from the clips in the
oven back panel.
LH oven
Remove the two screws holding the thermostat phial
to the oven fan cover at the rear of the oven. Pull the
unit forward to access the rear of the cooker. Remove
the both cover boxes by removing the fi xing screws
and lifting clear. Feed the thermostat capillary clear of
the oven. Disconnect the wires from the thermostat
and undo the two fi xings that secure the control to the
mounting plate. Fit the replacement and re-assemble in
reverse order. Ensure that the phial is clipped to the oven
rear, positioned centrally between the clips.
Check that the thermostat functions correctly.
9 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
Pull the cooker for ward to gain access to the cover
box. Undo the cover screws and lift clear. The cutout
is located on the earth plate be side the oven element
con nec tions. Disconnect the cutout wir ing. Undo the
fi xings that secure the cutout to the earth plate and
re move. Fit re place ment control and re-as sem ble in
reverse order.
10. To Remove an Oven Door
Open oven door. Support the door and remove the
two screws securing the upper hinge and gasket to the
cooker front. Remove the door from the lower hinge by
lifting slightly and moving outwards.
Reassemble in reverse order.
11. To Change Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel
fi xing screws from the door sides (two each side).
Carefully lift off the outer door panel.
Remove door handle from panel by unscrewing 2
retaining nuts. Fit door handle to new panel
Fit panel to door. Reassemble in reverse order.
12. To Change Oven Door Latch
Remove outer door panel (see 13). Remove screws ‘B’
holding latch assembly to inner door panel. Fit new
catch and reassemble in reverse order.
Check correct door operation.
28
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity servicing. Check appliance is safe when you have finished.
13. To Adjust an Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and
screw in or out as required until required fi t is obtained.
Retighten locking nut.
14. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks
on the rear face. At the corner pull seal diagonally away
from the door centre until that hook is released. Proceed
to the next hook and release it in a similar way, and so
on. Use force if the hooks are stiff , as the old seal will be
discarded.
When fi tting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of
the door, and proceed round the door snapping in each
hook in turn.
15. To Remove Oven Inner Back
Open the oven door. Remove oven furniture. For the LH
oven unscrew the 2 thermostat phial fi xing screws.
Remove the fi xings that secure the inner back to the
oven rear.
Lift the removable panel away. Re-assemble in reverse
order. Ensure that the retaining fi xings are fully
tightened. For the LH oven unscrew the 2 thermostat
phial fi xing screws. Remove the screws that secure the
inner back to the oven rear. Lift the removable panel
away. Re-assemble in reverse order. Ensure that the
retaining fi xings are fully tightened.
16. To Replace an Oven Fan
Disconnect from the electricity supply.
Pull cooker forward to gain access to the rear. Remove
screws securing the electric cover to the back sheet and
remove cover. Disconnect the 3 terminals connected to
the fan noting their position. Remove oven inner back
(see 15).
Hold the fan blade and remove the centre nut (left hand
thread) 2 brass washers, fan blade and circlip. Unscrew
fan retaining nuts and washers (3 off each) and lift the
fan away from the rear of the cooker. Fit new fan and
reassemble in reverse order. Check operation of oven.
17. To Remove an Oven fan Element
Disconnect from electricity supply.
Pull the unit forward to access the cover boxes at the
rear of the appliance. Remove the fi xings that secure
the cover and lift it clear. Undo the terminal connections
noting their positions. Remove the inner back as
detailed in Section 22. Remove the fi xings that secure
the element within the oven and lift the element away
carefully. Fit the replacement element and re-assemble
parts in reverse order. Check that the oven operates
correctly.
29
WARNING SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
18. To Remove the LH Oven Bottom and Top
Elements
Disconnect from the electricity supply.
Bottom Element
Pull the cooker forward to access the cover boxes at the
rear of the unit. Remove the fi xings that secure the cover
and lift it clear.
Remove the 2 screws ‘A’ and allow the plate to drop
down. Remove the 2 screws B, lower the upper plate and
remove through the slot in the cooker back.
Undo the terminal connections, noting their positions.
Remove the element fi xings and withdraw element.
Replace the element and re-assemble parts in reverse
order.
Top Element
Open the LH oven door and undo the fi xings that secure
the heat shield. Remove the top element bracket fi xings
and withdraw element. Replace the element and reassemble parts in reverse order. Check that the oven
operates satisfactorily.
30
A Left hand end dual circuit hob energy regulator
B Left hand rear hob energy regulator
C Left hand front hob energy regulator
D Right hand rear hob energy regulator
E Earth terminal
F Right hand front hob energy regulator
G Right hand Warmer / hob controller
H Left hand oven thermostat
I Left hand oven function switch
J Clock
K1 Right hand oven thermostat
K2 Right hand oven switch
L Line terminal
M Warmer Element
N Neutral terminal
O
1 Oven light switch left hand
O
2 Oven light switch right hand
P
1 Oven light bulb left hand
P
2 Oven light bulb right hand
Q1 Base element 1.0kW
Q2 Top element 1.2kW
Q3 Browning element 1.15kW
Circuit Diagram
Q4 Fan oven element 2.5kW
R Left hand oven fan
S Right hand Fan oven element 2.5kW
T Right hand oven fan
U Hob indicator neons
V Facia indicator neons
W Cooling fan
X
1 Thermal cutout left hand oven fan element
X
2 Thermal cutout left hand oven Q1, Q2 elements
X
3 Thermal cutout right hand oven fan element
Colour Code
b Blue
bl Black
br Brown
g/y Green & yellow
or Orange
r Red
v Violet
w White
w/y White with a yellow end marker
w/b white and black
y Yellow
Connection shown in circuit diagram is for single phase. Ratings are for 230V 50Hz
31
Technical Data
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION : DATA BADGE LOCATION : Lower right hand cooker upright (Remove storage drawer)
Country of Destination: GB/IE
Dimensions
Overall height
minimum 900mm maximum 925mm
Overall width
1100mm See ‘Positioning of Cooker’
Overall depth
648mm
Space for fixing
See ‘Positioning of Cooker’
Minimum space above hotplate
650mm
Ratings
Total Load At 230V 50Hz 13.6kW (approximate total including oven lights, oven fan etc.)
Hob
Ovens
Left hand Multifunction Oven Right hand Fan Oven
Fan element
2.5kW 2.5kW
Top element
1.2kW
Browning Element
1.15kW
Bottom element
1.0kW
Ovens
Multifunction Forced air convection
Energy efficiency class :
on a scale of A (more effi cient) to G (less effi cient)
BA
Energy consumption based on standard load
0.90kWh 0.85kWh
Usable volume (litres)
62 67
Size
Medium Large
Time to cook standard load
41 minutes 38 minutes
Baking area
1400cm
2
1400cm
2
Loading...