RDW459FI/SF
Dishwasher
User Guide
&
Installation & Service Instructions
U110143 - 01
Contents
1. Before You Start 1
At Time of Delivery 1
During Installation 1
During Normal Use 1
If a Fault Occurs 1
Caring for the Environment 1
2. Overview and Operation 2
Getting to Know Your Dishwasher 2
Salt 3
Rinse Aid 4
Detergent 4
What you should not put into the
dishwasher
Damage to glassware and other dishes 5
Arranging Crockery, Glasses, etc. in the
Dishwasher
Washing Dishes 7
Programme Overview 8
Using 3-in 1 Detergent Tablets 9
4. Troubleshooting 14
Resolving minor problems yourself 14
Problems when the unit is switched on 14
Problems with the appliance 14
Problems during washing 15
Problems with the dishes, cutlery, etc. 15
5. Installation 16
Positioning the Dishwasher 16
Cold Water Connection 16
Drain Hose Connection 16
Electrical Connection 17
5
6
Levelling the Dishwasher 17
Fitting the Decor Door 18
Securing the Dishwasher 19
Adjusting the Door Springs 19
Fitting the Plinth 19
6. General Information 20
7. Circuit Diagram 21
3. Looking after your Dishwasher 12
Care 12
Overall Condition of the Appliance 12
Solvents or Abrasive Cleaning Products 13
Moving the Appliance 13
Seals 13
When You Go on Holiday 13
8. Technical Data 22
Due to our policy of continual improvement, we reserve the right to change specications without prior notice.
1. Before You Start
DocNo.800-0101 - Introduction
At Time of Delivery
Check packaging and dishwasher immediately for signs of
transport damage. If the appliance is damaged DO NOT USE.
Contact your supplier or customer services.
Please dispose of packaging materials properly.
During Installation
• Site the dishwasher and connect in accordance with the
installation instructions.
• DO NOT connect the dishwasher to the electricity
supply while carrying out the installation.
• Make sure that the wiring is properly earthed.
• The mains electricity supply must conform to the details
shown on the dishwasher nameplate.
• DO NOT connect the dishwasher to the electricity
supply with an extension cable.
• Built-under and built-in appliances should always be
installed under a continuous work surface attached
to adjacent cupboards. This will make sure that the
appliance is stable.
• After the appliance has been installed, the mains plug
should be easily accessible.
• DO NOT excessively bend or flatten the power supply
cord during installation.
During Normal Use
• The dishwasher MUST only be used for washing
household dishes and cooking utensils.
• This appliance cannot be installed outdoors.
• DO NOT place any heavy objects or stand on the door
when it is open. The appliance may tip forward.
• The water inside the dishwasher is NOT suitable for
drinking.
• DO NOT use solvents of any kind inside your
dishwasher. They could cause an explosion.
• Open the door very carefully if the dishwasher is
operating.
• NEVER touch the dishwasher with wet hands.
• If the appliance is not operating properly or
maintenance is required, disconnect from the power
supply.
• Children should be supervised.
• Keep detergents out of reach of children.
If a Fault Occurs
If the appliance malfunctions, turn o the water supply and
disconnect the plug from the wall socket. If you cannot solve
the problem, contact your service centre.
Only authorized persons should make repairs.
If the supply cord is damaged it must be replaced by the
manufacturer, service agents or authorized persons.
To maintain the eciency and safety of this appliance we
recommend:
• Call only Service Centres authorized by the
manufacturer.
• Always use original spare parts.
Caring for the Environment
Disposing of your packaging
Your new dishwasher was protected by suitable packaging
while on its way to you. All of the materials used are
environmentally friendly for disposal and can be recycled.
Please make a contribution to protecting the environment by
disposing of the packaging appropriately.
Disposing of your old dishwasher
Old appliances still have some residual value. An
environmentally friendly method of disposal will make sure
that valuable raw materials can be recovered and used again.
When an appliance has reached the end of its working life
unplug it from the mains. Cut o the mains cable and dispose
of it together with the plug.
Destroy the door locking mechanism so that children cannot
accidentally lock themselves in.
This symbol on the product or its packaging
indicates that the product may not be treated as
ArtNo.000-0019
Do not bin logo
By disposing of this product correctly, you will help prevent
potential negative consequences for the environment and
human health, which could otherwise be caused.
For more detailed information about recycling of this
product, please contact your local council, your household
waste disposal service or the shop where you purchased the
product.
household waste. Instead it should be handed
over your local community waste collection/
recycling centre.
1
2. Overview and Operation
Getting to Know Your Dishwasher
Dishwasher Interior (Fig.2-1)
Fig.2-1
A
B
C
D
DocNo.800-0203 - Overview - RDW459 diswasher
J
E
A Upper rack
B Upper spray arm
C Cutlery basket
D Lower rack
E Control panel
F Lower spray arm
G Salt container cap
H Washing lter
Detergent and rinse aid
I
dispenser
J Water inlet hose
K Drain hose
L Power supply cord
Control Panel (Fig.2-2)
Fig.2-2
AB
K
L
F
G
H
I
F
A ON-OFF button
B ON-OFF indicator
C Delay start button
CD HI JEG KL
D Additional options button
E Time remaining indicator
F Programme symbols
G Additional options symbols
H Inlet fault indicator
I Low rinse aid indicator
2
J Low salt indicator
K Programme button
L Start/reset button
Salt
Low salt indicator
The hardness of water varies from place to place. If hard water
is used in the dishwasher, deposits will form on the dishes
and utensils.
The appliance is equipped with a special softener that uses a
salt specically designed to eliminate lime and minerals from
the water.
Loading the salt into the container
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and
should be lled as follows:
1. When the low salt indicator (Fig.2-3) lights, you must ll
the salt. Remove the lower rack and then unscrew and
remove the cap from the salt container.
Note: If you are lling the container for the rst time, ll
it with water.
2. Place the end of the funnel (supplied) into the hole
and introduce about 2 kg of salt. It is normal for a small
amount of water to come out of the salt container.
3. Carefully screw the cap back on.
IMPORTANT: To prevent the formation of rust, load the salt
just before beginning a wash cycle.
Adjusting salt consumption
The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the hardness of the water used.
This is intended to optimize and customize the level of salt
consumption so that it remains at a minimum.
To adjust salt consumption:
1. Unscrew the cap from the salt container.
2. There is a ring on the container with an arrow on it
(Fig.2-4).
3. If necessary, rotate the ring in a counter-clockwise
direction from the ‘–‘ setting towards the ‘+’ sign, based
on the hardness of the water being used.
Fig.2-3
Fig.2-4
ArtNo.800-0204 -
Adjusting the salt
Water Hardness
Level
Clarke
degrees
1 0-10 0-17 0-1.7 0
2 10-25 18-44 1.8-4.4 – 20 60
3 25-50 45-89 4.5-8.9 MED 40 40
4 >50 >89 >8.9 + 60 25
°dH mmol/l
Selector
position
Salt
consumption
cycle
Autonomy
(cycles/2kg)
Table 2-1
We recommend that you adjust the salt consumption in
accordance with Table 2-1.
The default setting of the water softening system is:
• If using multi-functional tablets fill the salt dispenser
and set the adjuster to ‘–’;
• If the hardness of the water is greater than 60°fH, set it
to ‘+’.
3
Low rinse aid indicator
Fig.2-5
Rinse Aid
This product makes dishes sparkle and helps them to dry
without spotting. The dispenser is located on the inside panel
of the door.
When the low rinse aid indicator on the control panel
(Fig.2-5) and the indicator on the dispenser (Fig.2-6) lights
you must add rinse aid.
Note: When 3-in-1 or similar combination detergent tablets,
the rinse-aid is no longer useful.
Fig.2-6
Fig.2-7
ArtNo.800-207 - Dispenser - Removing the rinse aid cap
Fig.2-8
Loading the rinse aid
To load the rinse aid:
1. To open the dispenser, turn the cap in a counter-
clockwise direction and remove (Fig.2-7).
2. Pour in the rinse aid, making sure not to overll.
Regulate the amount of rinse aid used for each cycle by
turning the dose adjuster (Fig.2-8), located beneath the cap,
with a screwdriver.
There are 6 dierent settings; the normal dosage setting is 3.
IMPORTANT: Proper dosage of rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjuster should be turned to a higher setting. If
the dishes have white streaks, turn the adjuster to a lower
setting.
Detergent
Detergent specically intended for use with dishwashers
must be used. The dispenser must be relled before the start
of each wash cycle following the instructions provided in the
‘Programme overview’. The detergent dispenser is located on
the inside panel of the door.
Loading the detergent
To load the detergent:
1. Open the cover on the dispenser by pressing the button
(Fig.2-9).
2. Pour the detergent for the wash cycle into compartment
‘A’ (Fig.2-10).
3. Pour the detergent for the prewash cycle into
compartment ‘B’ (Fig.2-10).
4. After the detergent has been placed in the dispenser,
close the cover and press down until it clicks in place.
Note: To allow the cover to close properly, remove any excess
detergent from the edges of the dispenser.
If you are using 3-in-1 or similar tablets, make
sure you select the combination detergent tablet
function.
4
What you should not put into the
dishwasher
Cutlery and tableware manufactured in whole or part from
wood. They become faded and unsightly in appearance.
Furthermore the adhesives that are used are not suitable for
the temperature that occurs inside the dishwasher.
Delicate decorative glassware and vases, special antiques or
irreplaceable china. The decorative patterns on such items
will not be dishwasher-proof.
Plastic objects that are not resistant to hot water, copper and
pewter utensils are also not suitable. Decorative patterns
printed or painted onto the surface of crockery, glasses, etc.,
aluminium and silver items tend to become discoloured or
faded if washed in the dishwasher.
Some types of glass can become opaque in appearance after
they have been washed many times in a dishwasher. Highly
absorbent materials, such as sponges and towels should
never be placed in the dishwasher.
IMPORTANT: Dishes or cutlery that have been soiled by
tobacco ash, wax, grease or paint, should not be put in the
dishwasher.
A B
Fig.2-9
Fig.2-10
Damage to glassware and other dishes
Possible causes
• Type of glass or manufacturing process.
• Chemical composition of detergent.
• Water temperature and duration of dishwasher
programme.
Suggested remedy
• Use glassware or porcelain dishes that have been
marked ‘dishwasher-proof’ by the manufacturer.
• Use a mild detergent that is described as ‘kind to dishes’.
If necessary, seek further information from detergent
manufacturers.
• Select a programme with a low temperature and a short
duration.
• To prevent damage, take glass and cutlery out of the
dishwasher as soon as possible after the programme
has ended.
5
ArtNo.800-0304 - Using the cup rack
Fig.2-11
Arranging Crockery, Glasses, etc. in the
Dishwasher
Before placing the dishes in the dishwasher, remove larger
food particles to prevent the lter from becoming clogged,
resulting in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they are soaked before
washed. This will eliminate the need for extra wash cycles.
ArtNo.800-0319 - RDW459 - Lower rack
Fig.2-12
A
ArtNo.800-0308 - Adjusting the upper rack
Fig.2-13
Pull out the rack to load the dishwasher.
Using the lower rack
The lower rack has adjustable supports that fold down to
allow larger items to be placed. We recommend that you
place the most dicult to clean items on the lower rack: pots,
pans, lids, serving dishes and bowls (Fig.2-11).
It is preferable to place serving dishes and lids on the sides of
the racks to avoid blocking the rotation of the top spray arm.
Pots, serving bowls, etc. must always be placed face down.
Deep pots should be slanted to allow the water to ow out.
C
B
D
WARNING!
Knives and other utensils with sharp points must
be loaded in the basket with their points down or
placed in a horizontal position.
Using the upper rack
The upper rack (Fig.2-12) is designed to hold more delicate
and lighter dishware, such as glasses, cups and saucers,
plates, small bowls and shallow pans (as long as they are not
too dirty).
Position the dishes and cookware so that the spray of water
does not move them.
ArtNo.800-0320 - RDW459 - Upper rack
The upper rack can be adjusted for height (Fig.2-13). Undo
the retaining clips on the telescopic runners (A). Slide the rack
out (B), ret on the lower wheels and push back along the
runners (C). Close the retaining clips (D).
Adjust the upper basket to the higher level and you have
more space to accommodate taller pans and trays in the
bottom basket.
Shelf
Fig.2-15Fig.2-14
Lean tall glasses and those with long stems against the shelf.
DO NOT lean them against other items to be washed.
Place glasses, cups and small bowls on the additional cup
rack. The additional cup rack can be swivelled in or out as
required (Fig.2-14).
Knife rack
The knife rack clips onto the side of the top basket, giving you
the freedom to wash your large sharp knives separately and
out of harm’s way (Fig.2-15).
6
On/O button
On-O indicator
Start/reset button
Washing Dishes
Programme overview
Time delay
Press for additional options (scroll through):
Upper rack wash function
Lower rack wash function
Combi detergent tablets function
Program select
Start/reset button
Programme selection
The most appropriate programme can be identied by
comparing the type of crockery, cutlery, etc., as well as the
amount and condition of food remains, with the details
contained in Table 2-2, the wash cycle table.
The corresponding programme sequence, duration and
consumption details are shown in the right half of the table.
Example: Use the normal programme for dishes and utensils
that are heavily soiled.
Fig.2-16
Fig.2-17
Programme indicator Programme button
Programme data
The stated programme data are based on standard operating
conditions. The values can vary considerably according to:
• Different amounts of dishes
• Temperature of mains water supply
• Pressure of mains water supply
• Ambient temperature
• Fluctuations in mains voltage
• Machine-related factors (e.g. temperature, water
volume)
Switching the dishwasher ON
1. Turn on the tap.
2. Open the door.
3. Set ON-OFF button to ON (Fig.2-16); the ON-OFF
indicator will light and then all of the programme
indicators will light.
4. Press the programme button ‘P’; the programme
indicator will light (Fig.2-17).
5. Press the Start/Reset button (Fig.2-18); the
corresponding programme indicator will blink.
6. Close the door and the dishwasher will start
automatically.
Fig.2-18
End of programme
Six beeps will indicate that the wash cycle has nished and all
the programme indicators light.
7
Duration
ArtNo.030-0026 - Dishwasher - symbols
ArtNo.030-0026 - Dishwasher - symbols
ArtNo.030-0026 - Dishwasher - symbols
ArtNo.030-0026 - Dishwasher - symbols
ArtNo.030-0026 - Dishwasher - symbols
ArtNo.030-0026 - Dishwasher - symbols
Rinse aid
(mins)
wash
Extended
112
u
94
u
102
u
90
u
162
u
140
u
92
u
82
u
32
u
32
u
54
u
48
u
12
u
12
u
Upper
Delayed
Additional options Detergent
Description of cycle
of food
Condition
Prewash
wash
start
Tabs
remaining
5g 22g
– 5g 22g
u
uu
Prewash with warm water.
Extended wash at 70°C.
Rinse with cold water.
Rinse with hot water.
Drying.
hard
Stuck on
Prewash with cold water.
5g 22g
– 5g 22g
uu
Extended wash at 55°C.
Rinse with cold water.
Rinse with hot water.
– 5g 22g
u
Drying.
Prewash with cold water.
Extended wash at 50°C.
5g 22g
– 5g 22g
u
uu
Rinse with cold water.
Rinse with hot water.
Drying.
Loosely
attached
uu
Wash at 45°C.
Rinse with warm water.
Rinse with hot water.
5g 22g
u
Drying.
– – 15g
u
Short wash at 40°C.
Rinse with hot water.
Loosely
attached
– – 15g
– 5g 22g
u
Extended wash at 65°C.
Rinse with cold water.
5g 22g
–––
u
–––
u
Table 2-2
Rinse with hot water.
Drying.
Short cold wash to prevent
food residue from drying on
the dishes.
of food
Amount
remaining
remaining
Type of food
china, pots & pans,
cutlery, glassses, etc.
Types of crockery e.g.
Wash
programme
Programme Overview
A lot.
Soups, casseroles,
sauces, potatoes,
pasta, rice, eggs, roast
or fried food.
Non-delicate
70 °C
Intensive wash
55 °C
Normal wash
A little.
Soups, potatoes,
pasta, rice, eggs, roast
or fried food.
50 °C
Light wash
Coee, cakes, milk,
45 °C
Glassware
sausage, cold drinks,
salads.
8
Very little.
Mixed
40 °C
Rapid wash
Soups, potatoes,
pasta, rice, eggs, roast
or fried food.
65 °C
Heat wash
Rinse o if the dishes have been stacked for several
days in the dishwasher prior to washing.
Soak
Switching the dishwasher OFF
Several minutes after the programme has ended:
1. Open the door.
2. Set the ON-OFF button to OFF.
3. Remove dishes, etc. when they have cooled down.
Note: For the best drying performance, we recommend that
you do not remove the contents for at least 30 minutes. This
allows residual heat in the dishwasher to remove any small
droplets of water that may occur.
Interrupting the programme
A cycle that is underway can be modied if it has only been
running for a short time. Otherwise, the detergent may have
already been used, and the appliance may have already
drained the wash water. If this is the case the detergent
dispenser must be relled; see ‘Loading the detergent’.
To cancel a programme that is underway, carefully open
the door and press the programme button and hold it in for
about 3 seconds.
CAUTION!
There is a risk of water coming out from inside the
appliance. DO NOT open the door fully until the
spray arm has stopped rotating.
Using 3-in 1 Detergent Tablets
General Advice
1. Before using these products you should rst check
that the water hardness in your supply is compatible
with their use, as per the detergent manufacturers
instructions (on the product packaging).
2. These products should be strictly used according to the
detergent manufacturers instructions.
3. If you encounter problems when using 3-in-1 products
for the rst time then please contact the detergent
manufacturers care line (the telephone number is given
on the product packaging).
Special Advice
When using combination products, the rinse-aid and salt
lights are no longer useful.
It may be helpful to select the lowest possible setting for
water hardness.
When you open the door, the dishwasher will beep ten times
every thirty seconds.
If the appliance has already heated up or the hot water was
switched ON and then the appliance door opened, leave the
door ajar for several minutes and then close.
After 30 seconds the programme will start from the point it
was interrupted.
Cancelling or modifying a cycle
A cycle that is underway can be modied if it has only been
running for a short time. Otherwise, the detergent may have
already been used and the appliance may have already
drained the wash water. If this is the case, the detergent
dispenser must be relled (see ‘Loading the detergent’).
To modify a cycle that is already underway, follow the
instructions contained in the paragraph entitled ‘Reset drain
function’ and select the programme you wish (see ‘Switching
the dishwasher ON’).
9
Start/reset button
Additional options button
Fig.2-19
Fig.2-20
To select the ‘tablets’ function:
1. Open the door.
2. Select the programme and then press the additional
options button (Fig.2-19) until the tablets indicator
[ ] lights.
3. Press the Start/Reset button (Fig.2-20) and close the
door. The dishwasher will start immediately.
To cancel the ‘tablets’ function:
Follow the ‘Cancelling or modifying a cycle’ instructions.
If you decide to switch to the use of a standard detergent
system we advise that you:
1. Rell both the salt and rinse aid compartments.
2. Switch the water hardness setting to the highest
possible position and run for three normal cycles
without a load.
3. Readjust the water hardness setting again according
to the conditions for your region. For more information
please refer to your instruction manual.
Upper rack wash
This function allows the dishwasher to wash dishes using
only the upper rack. This will allow you to save on water and
energy consumption if there are not enough dishes for a full
load.
To select upper rack wash:
Open the door. Select the programme and then press
1.
the additional options button until the upper rack wash
[ ] indicator lights (Fig.2-19).
2. Press the Start/Reset button (Fig.2-20) and close the
door, the dishwasher will start immediately.
To cancel the upper rack wash:
Follow the ‘Cancelling or modifying a cycle’ instructions.
Note: Please keep in mind that the amount of detergent
should also be adapted to the load.
10
Delayed start programming
Delayed start button
Start/reset button
You can delay the start of a programme from 1 hour up to
24hours.
1. Open the door, switch the dishwasher ON.
2. Press programme button to choose the desired
programme.
3. Press the Delayed Start button (Fig.2-21); the time-
remaining indicator changes to ‘1’.
4. Press the Delayed Start button as many times as
necessary until the numerical display shows the
required delay.
5. To cancel the time delay setting, press the Delayed Start
button until the time remaining indicator goes out.
6. Press the Start/Reset button (Fig.2-22) and close the
door, the time-remaining indicator will blink and start
to count down. The programme will start when the
delayed start indicator goes out and the wash cycle will
begin.
To cancel a delayed start programme in progress, follow the
‘Cancelling or modifying a cycle’ instructions.
Reset drain function
You can use the Reset Drain function to stop the washing
cycle from running. Press the Start/Reset button for 3seconds
to reset. The dishwasher will stop after a few minutes drain
phase.
Fig.2-21
Fig.2-22
11
Low salt indicator
ArtNo.800-0501 - Cleaning the filter 1
ArtNo.800-0502 - Cleaning the filter 2
3. Looking after your Dishwasher
Low rinse aid indicator
Fig.3-1
Fig.3-2
Fig.3-3
Care
After Every Wash
After every wash, set the ON-OFF button to OFF and leave the
door slightly ajar so that moisture and odours are not trapped
inside.
Before cleaning or performing maintenance isolate
from mains.
Overall Condition of the Appliance
Check that no grease or scale has accumulated on the inside
of the dishwasher. If you discover any deposits: Clean the
interior of the dishwasher thoroughly with a detergent
solution.
Dishwasher salt
Check the LOW SALT indicator (Fig.3-1). If required, top up
with salt .
Rinse aid
Check the low rinse indicator (Fig.3-2) on the control panel. If
required, top up with rinse aid.
Filters
The lters prevent larger particles of food in the water from
reaching the pump. These particles may occasionally block
the lters.
Fig.3-4
When the appliance has nished washing, check the lters for
particles of food and, if required, clean.
After undoing the coarse micro-lter (Fig.3-3), the lter unit
can be removed (Fig.3-4). Remove any particles of food and
rinse the lters under running water.
Insert the lter unit and tighten the coarse micro-lter.
12
Spray arms
ArtNo.800-0505 - Cleaning the lower spray arm
Limescale and remnants of food in the washing water can
block the nozzles in the spray arms and the arm mountings.
Inspect the nozzles in the spray arms for blocked holes due to
remnants of food.
If necessary, pull the lower arm (Fig.3-5) upwards and lift it
o. Unscrew the upper spray arm (Fig.3-6).
Clean both spray arms under running water.
Ret the spray arms. Make sure that the lower arm
has locked into place and the upper one is screwed
tight.
Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use
a cloth dampened with water and a little white vinegar or a
cleaning product made specically for dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical
position. If absolutely necessary, it can be positioned on its
back.
Fig.3-5
Fig.3-6
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this from
occurring.
When You Go on Holiday
When you go on holiday, it is recommended that you run a
wash cycle with the dishwasher empty and isolate from the
mains. Turn o the water supply and leave the door of the
appliance slightly ajar. This will help the seals last longer and
prevent odours from forming within the appliance.
13
4. Troubleshooting
DocNo.800-0401 - Troubleshooting - RDW6012 dishwasher
Fig.4-1
Fig.4-2
Fig.4-3
Resolving minor problems yourself
Experience has shown that you can resolve most problems
that occur during normal daily usage yourself, without having
to call out a service engineer. Not only does this save costs
but it also means that the appliance is available to use. The
following list of common occurrences and their remedies
should help you identify the causes of most problems.
Problems when the unit is switched on
Appliance does not start up
• Fault with fuse in mains electricity supply.
• Plug not inserted in wall socket.
• Appliance door not closed properly.
• Programme button has not been pressed. Water tap not
turned on.
• Blocked strainer in water intake hose.
CAUTION!
Remember that repairs should only be carried out by
a suitably qualied specialist. Improper repairs can
lead to considerable equipment damage as well as
danger to the user.
Problems with the appliance
Error display on the time remaining indicator
When the buzzer emits 10 short warning signals every
30seconds, the time remaining indicator displays ‘E3’ and the
programme indicator lights (Fig.4-1). Check if:
• The drain hose is too low.
When the buzzer emits 10 short warning signals every
30seconds, the time remaining indicator displays ‘E4’ and the
programme indicator lights (Fig.4-2). Check if:
• The drain hose is crimped or bent;
• The drain hose is too high.
When the buzzer emits 10 short warning signals every
30seconds, the time remaining indicator displays ‘E5’ and the
programme indicator lights (Fig.4-3). Check if:
• The water is turned on and the hose is connected
properly;
• The water supply to the house is on and has sufficient
pressure;
• The water supply hose is crimped or bent;
• The filter for the water supply hose is clogged;
• The drain hose is too low.
When the buzzer emits 10 short warning signals every
30seconds and the time remaining indicator displays E2 or
E6, contact the nearest authorized service centre.
If, after these checks the dishwasher still does not function or
has any other error displayed, then press the ON-OFF button
to OFF. Wait a few minutes then turn the dishwasher back on
and try again.
14
If the dishwasher still does not function and/or the problem
persists, contact the nearest authorized service centre and
provide them with the following information:
1. The nature of the problem.
2. The model type number (Mod...) and serial number
(S/N...), as indicated on the plate located on the side of
the inner part of the door.
Lower spray arm rotates with diculty
• The spray arm is blocked by small items or food remains.
Lid in detergent compartment cannot be closed
• Detergent compartment has been overfilled.
• Mechanism is clogged with remnants of detergent.
• Items in the rack were touching each other.
• Not enough detergent was added to dispenser.
• Selected wash programme was not intensive enough.
• Rotation of spray arm obstructed by dishes, etc.
• Nozzles in spray arm are blocked by remnants of food.
• Filters are blocked.
• Filters have been incorrectly fitted.
• Waste water pump is jammed.
Plastic items are discoloured
• Not enough detergent was added to dispenser.
• Detergent has insufficient bleaching properties. Use a
detergent containing a chemical bleaching agent.
Remnants of detergent stuck inside dispenser
• Compartment was damp when it was filled up with
detergent. Compartment must be dry before detergent
is added.
Water remains inside appliance after programme has
ended
• Blockage or kind in drainage hose.
• Pump is jammed.
• Filters are blocked.
• The programme is still running. Wait for the programme
to end.
Problems during washing
Unusual amount of foam
• Normal washing up liquid has been poured into the
rinse-aid container.
• Excess amount of rinse aid. Remove any spilled rinse
aid with a cloth as it could otherwise lead to excessive
foaming during the next washing cycle.
Appliance stops suddenly while washing is taking place
• Electricity supply to appliance has been cut off.
• Water supply has been interrupted.
Knocking sound can be heard while washing is taking
place
• A spray arm is knocking against the dishes inside the
appliance.
Rattling sound can be heard while washing is taking place
• Crockery has not been stacked properly inside the
appliance.
Knocking sound coming from inlet valves
• This is caused by the way the water pipes have been
laid and it has no effect upon the way the appliance
functions.
Problems with the dishes, cutlery, etc.
Remnants of food are stuck to the dishes, cutlery etc.
• Dishwasher was not loaded properly. Jets of water could
not reach all parts of the dishes, etc.
• Too many items in the rack.
White stains are left on crockery and glasses have a milky
appearance
• Not enough detergent added to the dispenser
compartment.
• Amount of rinse-aid set too low.
• Although water is quite hard, no salt has been put in
appliance.
• Water softener set too low.
• Lid on salt container not screwed tight.
• If you use a phosphate-free detergent, try a detergent
containing phosphates and compare results.
Dishes, cutlery, etc. have not been dried
• Selected programme did not include drying function.
Amount of rinse-aid set too low.
• Items were removed from dishwasher too soon. For the
best drying performance, do not remove the contents
for at least 30 minutes. This allows residual heat in the
dishwasher to remove any small droplets of water that
may occur.
Glasses have a dull appearance
• Amount of rinse-aid set too low.
Tea stains or traces of lipstick have not been completely
removed
• Detergent does not have a sufficient bleaching effect.
• Washing temperature set too low.
Traces of rust on cutlery
• Cutlery is not rustproof.
• Salt content in washing water is too high.
• Lid on salt container not screwed tight.
• Salt spilt while filling container.
Glasses become clouded and discoloured; coating cannot
be wiped o
• Unsuitable detergent was used.
• Glasses are not dishwasher-proof.
Smears left behind on glasses and cutlery; glasses have
acquired a metallic appearance
• Amount of rinse-aid set too high.
15
450-550
80
ArtNo.800-0101 - Cold water connection
Washer
Water hose
¾“ BSP tap connector
5. Installation
• DocNo.800-0503 - Installation - RDW459 dishwasher
Fig.5-1
Fig.5-2
Positioning the Dishwasher
The dishwasher should be aligned to the front of the adjacent
cabinets, with allowance made for the door thickness. The
dishwasher has water supply and drain hoses that can be
positioned on either to the left or the right.
Before installing the dishwasher into a kitchen cabinet,
holes must not be drilled into the sides, or door, to avoid
compromising the performance and operation of the
appliance.
A plastic self-adhesive anti-condensation strip is supplied
with the dishwasher. Fix the strip to the underside of the
worktop, along the front edge (Fig.5-1).
Connect up the cold water supply, the drain hose and the
electrical connections (see below) then slide the dishwasher
into the cabinet opening. Make sure the unit sits on the
plastic skids supplied.
Cold Water Connection
Connect the water supply hose (supplied loose) to the cold
water inlet at the rear. Connect the other end to a ¾“ BSP tap
connector (Fig.5-2). Make sure that the washers are in place
and that it is fastened securely in place.
Fig.5-3
Fig.5-4
40cm
Waste hose support
(xed to wall)
100cm
IMPORTANT: If the water pipes are new or have not been
used for an extended period of time, run the water for
a while to make sure that the water is clear and free of
impurities BEFORE connecting to the dishwasher. Failure
to carry out this precaution may lead to the water inlet
becoming blocked and causing damage the appliance.
Drain Hose Connection
Connect the drain hose the water outlet. Insert the hose into
a drainpipe with a minimum diameter of 40 mm, or let it
run into a sink, making sure to avoid bending or crimping. If
necessary, t a siphon trap (U-bend) with a connecting piece.
The free end of the hose must be at a height of between 40100 cm and must not be immersed in water (Fig.5-3).
WARNING! The connecting piece for the siphon trap
(U-bend) must be solidly fastened to the wall to
prevent the drain hose from moving and allowing
water to spill outside the drain (Fig.5-4).
Waste
hose
To waste
16
Electrical Connection
A
B
The dishwasher must be installed by a qualied electrician,
in accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
WARNING: THIS APPLIANCE MUST BE EARTHED
All external wiring must comply with the IEE Regulations
for the Electrical Equipment of Buildings. Connection to the
electrical supply can be made with either a plug and socket
or be permanently wired via a double pole switch. The
dishwasher is supplied with a 3-core cable.
Should the plug not t the socket in your home, it should be
removed and replaced with a suitable plug.
Note: If the plug is tted is not suitable, it must be cut o and
disposed of properly. To avoid the risk of electrocution, the
plug must not be left where children might nd it and plug it
into a supply socket.
Three pin plugs to BS 1363 with a capacity of not less than
13A must be used and tted with a 13 amp fuse ‘ASTA’
approved to BS 1362.
After replacing the fuse the cover must be retted. If the
cover is lost, the plug must not be used until a replacement
cover has been obtained from your supplier. The colour of the
correct fuse carrier is that of the coloured insert in the base of
the fuse recess, or stated elsewhere on the plug. Always state
this colour when ordering a replacement fuse carrier.
Fig.5-5
870 mm max
Adjustable feet
Plastic skid
ArtNo.800-0232 - RDW6015 - Raising the unit
Wooden spacer
Fig.5-6
IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
Green and yellow: EARTH
Blue: NEUTRAL
Brown: LIVE
CAUTION
The dishwasher plug must be accessible even when
the appliance is installed as a built-in unit so that
maintenance can be carried out safely.
Care for the external cable
• Hold the plug, not the electrical cable, when
unplugging the dishwasher.
• Make sure that the dishwasher does not trap the electric
cable.
• Do not step on the cable.
• Avoid damage to the electric cable when moving the
dishwasher.
Damaged electrical cable
If the electrical cable is damaged or worn, switch o the
dishwasher and consult an authorized agent for replacement.
Fig.5-7
A
B
ArtNo.800-0112 - Integrated panel 1
Levelling the Dishwasher
When the unit is in position, adjust the feet to level the
dishwasher. In any circumstance, the dishwasher should not
be inclined more than 2° otherwise the performance may be
aected.
17
ArtNo.800-0111 - Marking
the plate position
Fig.5-8
Fig.5-9
The adjustable feet allow the dishwasher to be raised up to
870 mm. If the space between the oor and the underside
of the work surface is more than 870 mm, the unit should be
positioned on suitable wooded spacers that should be xed
to the oor (Fig.5-5).
Always use a spirit level to make sure that the appliance
is level left-to-right and front-to-back. If the appliance is
installed on carpet, make sure that there is clearance beneath
the appliance.
Adjust the feet to raise and level the dishwasher to the correct
height (Fig.5-6). Using the tool supplied, adjust the rear feet
via the studs ‘A’ at the front of the appliance. Adjust the front
feet ‘B’ using the spanner provided.
To prevent damage to the oor surface, install the appliance
on the plastic skids supplied.
Fitting the Decor Door
Fig.5-10
ArtNo.800-0105 - Fitting the plastic hooks
A
B
ArtNo.800-0106 - Fitting the door
Fixing the door panel fittings
Place the template supplied on the back face of the door
panel. Align the top of the template, as identied by the
‘A’ arrow, with the top of the door and align the side of the
template with the left-hand edge of the door (Fig.5-7). Using
a pencil or bradawl, mark the positions of the holes closest
the door panel edge.
Repeat this step for the right-hand side of the door panel
using the other side of the template.
Align a mounting bracket with the two marks on the lower
left-hand part of the panel. Mark the remaining hole in the
top of the bracket (Fig.5-8) and then remove. Repeat for the
other side.
At the points marked, carefully drill 2mm holes to a
maximum depth of 10mm. Take care not to drill through to
the front face of the door panel.
Position the two brackets on the panel, with the tab facing
downwards. Using the screws supplied, x the brackets to the
panel.
Secure the two plastic hooks to the holes at the top of the
panel (Fig.5-9).
Fig.5-11
ArtNo.800-0107 - Securing the door
Mounting the door panel to the dishwasher
Insert the top plastic hooks into the slots on the dishwasher
front ‘A’. Carefully slide the panel up the channels until it
stops. Slide the panel downwards ‘B’, moving the bottom of
the panel door so that the bracket tabs locate into the slots in
the dishwasher front (Fig.5-10).
Align the top of the door panel with the adjacent cabinets.
Gently open the dishwasher door while supporting the door
panel. Secure the door panel using the screws supplied
(Fig.5-11). Cover the screw heads using the plastic caps
provided.
Note: If you have diculties tting the door (for example,
if doors are already tted to adjoining cabinets) then pull
the dishwasher out slightly to allow for easier access for the
door tabs. With the door tted, push the appliance back into
position.
18
ArtNo.800-0114 - Securing the dishwasher
ArtNo.800-0114 - Securing the dishwasher
Worktop
Adjoining
cabinet
Adjoining
cabinet
Bracket
Bracket
ArtNo.800-0119 - Adjusting the door springs
Securing the Dishwasher
Using the two screws supplied, secure the dishwasher to the
underside of the worktop (Fig.5-12).
For non-wooden worktops (e.g. marble) two brackets are
provided to allow the appliance to be secured to the sides
of the adjacent cabinets. Secure the appliance using the
two screws at the top of the chassis (Fig.5-13); adjust to the
correct width and then screw to the adjacent side panels
using suitable screws.
Adjusting the Door Springs
The door balance can be adjusted via two nuts accessed
through the two holes in the top of the front frame
(Fig.5-14). Using the tool supplied, adjust these until the
door remains just open under its own weight and is level
when open.
Fitting the Plinth
Cut clearance in the plinth to allow the door to fully open and
seal edges with a suitable silicon sealant to prevent water
ingress (Fig.5-15).
Fig.5-12
Fig.5-13
Fig.5-14
Fig.5-15
19
6. General Information
• DocNo.800-0605 - General information - RDW459ST
dishwasher
Fig.6-1
Fig.6-2
ArtNo.800-0320 - RDW459 - Upper rack
ArtNo.800-0319 - RDW459
- Lower rack
Measures must be taken to ensure that the units that are
subsequently re-sited as freestanding appliances cannot
topple over. This can be achieved by bolting the dishwasher
to the wall or tting it under a continuous work surface, that
is screwed to the adjacent cupboards.
Information on comparability tests
implemented in compliance with
EN 50242
Appliance loaded in accordance with standard specications.
Example of loaded dishwasher: see Fig.6-1 and Fig.6-2.
Capacity: 9 place settings
Comparability programme: Light wash
Rinse-aid setting: 5
Detergent: 5g + 22g
Height adjustable top-basket must be inserted in the
uppermost position. If the comparability tests do not fully
comply with EN 50242, e.g. degree of soiling, type of dishes
and cutlery, etc. contact the appliance manufacturer before
starting the test.
20
7. Circuit Diagram
• DocNo.800-0705 - Circuit diagram - RDW459SF dishwasher
A
220-240 Vac
50 Hz
N
T
L
Code Description
A PCB
B Half load valve
1 2 3 4 5 6 7 8 9 10 11 12
BCSDE F
CNF
G
H
Q
R
Code Description
K Thermal cut-out
M Thermostat sensor
Relay
N L
1 2 3 4 5 6
CN2
I
JMOP
K
C Dispenser
D Softer valve
E Inlet valve
F Drain pump
G Washing motor
H Capacitor for washing motor
I Temperature limiter
J Heater
O Low salt switch
P Low rinse aid switch
Q Pressure switch
R Overow switch
S Door switch
T EMI lter
21
8. Technical Data
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Inside face on the side of the door.
COUNTRY OF DESTINATION: GB/IE
Dimensions
446
580
450
820 - 880
820
725 max
All dimensions in mm
550
Connections
Electric 220 – 240V 50Hz
Ratings
Energy eciency class on a scale of A (more ecient) to G (less ecient) A
Standard cycle used Light wash
Energy consumption 0.80 kWh
Cleaning performance class A
Drying performance class A
Capacity 9 place settings
Water consumption 15 litres
Estimated annual consumption Energy: 250 kWh; Water: 4200 litres
Noise level 50 dB
Maximum rated current 10 A
Maximum total electric load at 230V 1.95 kW
22
232425
DocNo.000-0001 - Back cover Rangemaster
Clarence Street, Royal Leamington Spa,
Warwickshire, CV31 2AD, England.
Tel: +44 (0) 1926 457400 Fax: +44 (0) 1926 450526
E-mail: consumers@rangemaster.co.uk
ArtNo.000-0003 CE logo
www.rangemaster.co.uk
Loading...