Rangemaster Professional + 100, Kitchener 100, Classic 100, Hi-LITE 100 User's Manual & Installation Instructions

Download

Classic / Professional + / Kitchener / Hi-LITE

100 Dual Fuel

USER GUIDE &

INSTALLATION INSTRUCTIONS

Built from experience

To enter all you have to do is send in photos of your Rangemaster kitchen and tell us in one sentence what makes Rangemaster the heart of your kitchen? Entries can be posted on our Facebook page, Instagram or Twitter by tagging @RangemasterUK and using #MyRangemaster. Or, if you prefer, simply send in your entry via e-mail to marketing@agarangemaster.co.uk.

Rangemaster will feature a number of entries on the website online gallery and on the Rangemaster Facebook page, and some kitchens may be selected to be professionally photographed.

Show off your kitchen with ...

#MyRangemaster

This is

Terms & Conditions

1. This is my Rangemaster is open to residents of UK mainland only, aged 18 years & over. 2. All entries should be submitted to the advertised e-mail address, or Rangemaster UK Facebook, Instagram or Twitter page using the advertised hashtag & tag. 3. If we would like to professionally photograph your kitchen, you will be contacted via e-mail, Facebook / Twitter message or Instagram comment. 4. We cannot guarantee your kitchen will be professionally photographed. 4. Any photographs received and professional photographs taken will belong to AGA Rangemaster plc with full usage rights. E&OE.

Simply snap and share a picture of your kitchen and tag #MyRangemaster for the chance to win £200 of Rangemaster cookware. If selected we will also send a photographer round to professionally photograph you at home with your range. You might even feature in some of the UK’s top home interest titles!

Our range cookers are well known for providing the best

possible cooking performance and years of faithful service.

However, a great cooker alone cannot guarantee perfect

results every time. The other vital ingredients are of course

enthusiasm and quality cookware.

We offer cookware to work perfectly with all fuel types

manufactured by Rangemaster, including induction hobs.

You can be assured of functionality with style, as well as the

quality and meticulous attention to detail you expect from

the pioneers of range cooking.

Visit www.rangemastercookshop.co.uk

Search Rangemaster UK

Terms & Conditions Apply

Classic, Kitchener, Professional+ & Hi-LITE 100 Dual Fuel

U110077-10

Contents

1. Before You Start... 1

Important! 1 Installation and Maintenance 1 Peculiar smells 1 If you smell gas 1 Ventilation 1 Personal Safety 1 Cooker Care 2 Cleaning 2

2. Cooker Overview 3

Hotplate Burners 3 Wok Burner 4 The Wok Cradle (optional) 5 The Griddle (optional on Kitchener) 5 Main Oven Light 5 Fascia Illumination

(Hi-LITE only)

The Grill / Glide-out Grill

(optional) 6 The Ovens 6 Accessories 7

3. The Clock 8

4. Cooking Tips 13

Tips on Cooking with the Timer 13 General Oven Tips 13

5. Cooking Table 14

6. Cleaning Your Cooker 15

Essential Information 15 Hotplate Burners 15 The Wok Cradle 15 The Griddle 15 Grills 16 Control Panel and Doors 16 Ovens 17 The Tall Oven 17 Cleaning Table 18

7. Troubleshooting 19

8. Installation 21

Dear Installer 21 Safety Requirements and Regulations 21 Provision of Ventilation 21 Location of Cooker 22 Conversion 22 Positioning the Cooker 23 Moving the Cooker 23 Completing the Move 24 Fitting the Stability Bracket or Chain 24 Repositioning the Cooker Following

Connection 24 Conversion to Another Gas 25 Levelling 25 Gas Connection 25 Electrical Connection 26 Final Checks 27 Fitting the Plinth 27 Customer Care 27

9. Conversion to LP Gas 28

Injectors 28 Tap Adjustment 28 Stick on Label 28 Pressure Testing 29

10. Circuit Diagram 30

Classic 30 Professional+ & Kitchener 31 HI-LITE Fan Oven 32

11. Technical Data 33

Classic 33 Professional+ 34 Kitchener 35 Hi-LITE 36 Hotplate Eciency 37 Oven Data 38

Your cooker should give you many years of trouble-free cooking if installed and operated correctly. It is important that you read this section before you start, particularly if you have not used a dual fuel cooker before.

Important!



This appliance is designed for domestic cooking only. Using it for any other purpose could invalidate any warranty or liability claim. In particular, the oven should NOT be used for heating the kitchen – besides invalidating claims this wastes fuel and may overheat the control knobs.



This appliance is for use in Great Britain and the Republic of Ireland. It is a Cat II2H3+ cooker and is set for G20 at 20mbar. (A conversion kit for LPG is supplied with the cooker).

Installation and Maintenance

In the UK, the cooker must be installed by a Gas Safe registered engineer. The electrical installation should be in accordance with BS7671. Otherwise, all installations must be in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local gas and electricity supply companies’ requirements.

Ensure that the gas supply is turned on and that the cooker is wired in and switched on (the cooker needs electricity).

Set the clock to ensure that the oven is functional – see the relevant section in this manual.

It is recommended that this appliance is serviced annually.

Only a qualied service engineer should service the cooker, and only approved spare parts should be used.

Always allow the cooker to cool and then switch it o at the mains before cleaning or carrying out any maintenance work, unless specied otherwise in this guide.

Peculiar smells

When you rst use your cooker it may give o a slight odour. This should stop after a little use.

Before using for the rst time, make sure that all packing materials have been removed and then, to dispel manufacturing odours, turn the ovens to 200°C and run for an hour.

Before using the grill for the rst time you should also turn on the grill and run for 30 minutes with the grill pan in position, pushed fully back, and the grill door open.

Make sure the room is well ventilated to the outside air (see ‘Ventilation’ below). People with respiratory or allergy problems should vacate the area for this brief period.

If you smell gas

• DO NOT turn electric switches on or off.

• DO NOT smoke

• DO NOT use naked flames

• DO turn off the gas at the meter or cylinder

• DO open doors and windows to get rid of the gas

• DO keep people away from the area affected

• Call your gas supplier. If you are using natural gas in the UK, ring the National Grid

on: 0800 111 999.

Ventilation

The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Therefore, ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a powered cooker hood that vents outside. If you have several burners on, or use the cooker for a long time, open a window or turn on an extractor fan.

Personal Safety



Do not modify this appliance.



This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.



This appliance is not intended for use by young children or inrm persons unless they have been adequately supervised by a responsible person to make sure that they can use the appliance safely.



CAUTION: A long term cooking process has to be supervised from time to time. A short term cooking process has to be supervised continuously.



Danger of re: DO NOT store items on the cooking surfaces.



To avoid overheating, DO NOT install the cooker behind a decorative door.



WARNING: The appliance and its accessible parts become hot during use and will retain heat even after you have stopped cooking. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised.



DO NOT use a steam cleaner on your cooker.

1. Before You Start...



Accessible parts will become hot during use and will retain heat even after you have stopped cooking. Keep babies and children away from the cooker and never wear loose-tting or hanging clothes when using the appliance.

Always be certain that the controls are in the OFF position when the oven is not in use, and before attempting to clean the cooker.



When the oven is on, DO NOT leave the oven door open for longer than necessary, otherwise the control knobs may become very hot.



When using the grill, make sure that the grill pan is in position and pushed fully in, otherwise the control knobs may become very hot.



DO NOT use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

Always keep combustible materials, e.g. curtains, and ammable liquids a safe distance away from your cooker.



DO NOT spray aerosols in the vicinity of the cooker while it is on.

Use dry oven gloves when applicable – using damp gloves might result in steam burns when you touch a hot surface. Do not use a towel or other bulky cloth in place of a glove – it might catch re if brought into contact with a hot surface.



NEVER operate the cooker with wet hands.



DO NOT use aluminium foil to cover shelves, linings or the oven roof.



DO NOT use hotplate protectors, foil or hotplate covers of any description. These may aect the safe use of your hotplate burners and are potentially hazardous to health.



NEVER heat unopened food containers. Pressure build up may make the containers burst and cause injury.



DO NOT use unstable saucepans. Always ensure that you position the handles away from the edge of the hotplate.



DO NOT use cooking vessels on the hotplate that overlap the edges.

Never leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy spills may catch on re. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the smoking point.



WARNING! Unattended cooking on a hob with fat or oil can be dangerous and may result in re.



NEVER leave a chip pan unattended. Always heat fat slowly, and watch as it heats. Deep fry pans should be only one third full of fat. Filling the pan too full of fat can cause spill over when food is added. If you

use a combination of oils or fats in frying, stir them together before heating or as the fats melt.

Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or medium high temperatures. Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.



DO NOT use the top of the ue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels or softening butter.



DO NOT use water on grease res and never pick up a aming pan. Turn the controls o and then smother a aming pan on a surface unit by covering the pan completely with a well tting lid or baking tray. If available, use a multipurpose dry chemical or foam-type re extinguisher.

Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened (Fig. 1.1). When opening the oven stand well back and allow any steam to disperse.

Take care that no water seeps into the appliance.



This appliance is heavy so take care when moving it.

Cooker Care

As steam can condense to water droplets on the cool outer trim of the oven, it may be necessary during cooking to wipe away any moisture with a soft cloth. This will also help to prevent soiling and discolouration of the oven exterior by cooking vapours.

Cleaning

In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other food stu could result in a re.

Clean only the parts listed in this guide.

Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns. Some cleansers can produce noxious fumes if applied to a hot surface.

ArtNo.324-0001 Steam burst

Fig. 1.1

ArtNo.270-0001

Proplus control to high

The 100 dual fuel cooker (Fig. 2.1) has the following features:

A. 5 hotplate burners including a wok burner

B. Control panel incorporting a timer

C. Separate grill or glide-out grill (depending on model)

D. Main fan oven

E. Tall fan oven

Hotplate Burners

The drawing by each of the central knobs indicates which burner that knob controls.

Each burner has a Flame Supervision Device (FSD) that prevents the ow of gas if the ame goes out.

When the igniter button is pressed in, sparks will be made at every burner – this is normal. Do not attempt to disassemble or clean around any burner while another burner is on, otherwise an electric shock could result.

To light a burner, press the igniter button, and push in and turn the associated control knob to the high position as indicated by the large ame symbol (



), (Fig. 2.2).

The igniter should spark and light the gas. Keep holding the knob pressed in to let the gas through to the burner for about ten seconds.

Professional +

2. Cooker Overview

Fig. 2.1

Fig. 2.2

DocNo.020-0006 - Overview - 100DF - Prof+

ArtNo.311-0002 Pan with rim

If, when you let go of the control knob, the burner goes out, then the FSD has not been bypassed. Turn the control knob to the OFF position and wait for one minute before you try again, this time making sure to hold in the control knob for slightly longer.

Adjust the ame height to suit by turning the knob counterclockwise (Fig. 2.3). On this cooker the low position is beyond high, NOT between high and o.

If a burner ame goes out, turn o the control knob and leave it for one minute before relighting it.

Make sure that the ames are under the pans. Using a lid will help the contents boil more quickly (Fig. 2.4).

Large pans should be spaced well apart.

Pans and kettles with concave bases or down-turned base rims should not be used (Fig. 2.5).

Simmering aids, such as asbestos or mesh mats, are NOT recommended (Fig. 2.6). They will reduce burner performance and could damage the pan supports.

You should also avoid using unstable and misshapen pans that may tilt easily, and pans with a very small base diameter, e.g. milk pans, single egg poachers (Fig. 2.7).

The minimum recommended pan diameter is 120 mm. The maximum allowable pan base diameter is 260 mm.

DO NOT use cooking vessels on the hotplate that overlap the edges.

Wok Burner

The wok burner is designed to provide even heat over a large area. It is ideal for large pans and stir-frying (Fig. 2.8).

For heating smaller pans, the aforementioned hotplate burners may be more ecient.

You should wipe the enamel top surface of the cooker around the hotplate burners as soon as possible after spills occur. Try to wipe them o while the enamel is still warm.

Note:

The use of aluminium pans may cause metallic marking of the pan supports. This does not aect the durability of the enamel and may be cleaned o with an appropriate metal cleaner.

ArtNo.311-0001 Right pans gas

ArtNo.270-0003

Proplus control to low

Art No. 311-0003 Simmer aids

ArtNo.311-0004 Tipping wok

ArtNo.311-0005 Wok burner & pan support

Fig. 2.3

Fig. 2.4

Fig. 2.5

Fig. 2.6

Fig. 2.7

Fig. 2.8

ArtNo.090-0002 90 Griddle position

ArtNo.090-0004 Incorrect griddle position

ArtNo.311-0006 Correct wok sizes

The Wok Cradle (optional)

The wok cradle is designed to t a 35 cm wok. If you use a dierent wok, make sure that it ts the cradle. Woks vary very widely in size and shape. It is important that the wok sits down on the pan support – however, if the wok is too small, the cradle will not support it properly (Fig. 2.9).

The cradle should be used on the wok burner only. When you t the cradle, make sure that it is supported properly on a pan support and the wok is sitting level in the cradle (Fig. 2.10).

The cradle will get very hot in use – allow plenty of time for it to cool before you pick it up.

The Griddle (optional on Kitchener)

The griddle ts the left-hand pan support, front to back (Fig.

2.11). It is designed for cooking food on directly. DO NOT use

pans of any kind on it. The griddle surface is non-stick and metal cooking utensils (e.g. spatulas) will damage the surface. Use heat resistant plastic or wooden utensils.



DO NOT put it crossways – it will not t properly and will be unstable (Fig. 2.12).



DO NOT put it on any other burner – it is not designed to t in any of the other pan supports.

Position the griddle over the hotplate burners resting on the pan support. Check that it is securely located.

The griddle can be lightly brushed with cooking oil before use (Fig. 2.13). Light the hotplate burners. Adjust the ame heights to suit.

Preheat the griddle for a maximum of 5 minutes before adding food. Leaving it longer may cause damage. Turn the control knobs towards the low position, marked with the small ame symbol, to reduce the burner ames.



Always leave space around the griddle for the gases to escape.



NEVER t two griddles side by side (Fig. 2.14).

After cooking, allow the griddle to cool before cleaning.

Main Oven Light

Press the button to turn the light on (Fig. 2.15). If the oven light fails, turn o the power supply before changing the bulb. See the ‘Troubleshooting’ section for details on how to change the bulb.

Fascia Illumination

(Hi-LITE only)

To turn on the fascia illumination panel simply push the button in (Fig. 2.16). To turn this feature o, push the button once more.

ArtNo.311-0007 Wok stand close-up

ArtNo.311-0009 Oil on griddle

ArtNo.320-0017 Main oven light

ArtNo.311-0008 Griddle positioning

ArtNo.320-0017 Main oven light

Fig. 2.9

Fig. 2.10

Fig. 2.11

Fig. 2.12

Fig. 2.13 Fig. 2.14

Fig. 2.15 Fig. 2.16

The Grill / Glide-out Grill (optional)

Open the door and, using the handle, pull the grill pan (Fig. 2.17) or carriage (Fig. 2.18) forward.

The grill has two elements that allow either the whole area of the pan to be heated or just the right-hand half.

Adjust the heat to suit by turning the knob. To heat the whole grill, turn the knob clockwise (Fig. 2.19).

To heat the right-hand half, turn the knob counter-clockwise. The neon indicator light by the grill control will come on.

For best results, leave the grill pan in the grill chamber and preheat the appropriate part(s) of the grill for two minutes. The grill trivet can be removed and the food placed on it while you are waiting for the grill to preheat.



DO NOT leave the grill on for more than a few moments, without the grill pan underneath it, otherwise the knobs may become hot.

Once the grill has preheated, take the grill pan out again and put the trivet back in place with the food on it. Slide the grill pan or carriage back into the grill chamber. Make sure that it is pushed right in.



Accessible parts may be hot when the grill is in use. Young children should be kept away.

The grill pan trivet can be turned over to give two grilling positions (Fig. 2.20).



Never close the grill door when the grill is on.

The Ovens

The clock must be set to the time of day before the ovens will work. See the following section on ‘The Clock’ for instructions on setting the time of day.

References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed from the front of the appliance.

Both ovens are fan ovens that circulate hot air continuously, which means faster, more even cooking.

The recommended cooking temperatures for a fan oven are generally lower than a conventional oven.

Note: Please remember that all cookers vary so temperatures in your new ovens may dier to those in your previous cooker.

Operating the Ovens

1. Turn the oven knob to the desired temperature (Fig.

2.21).

2. The oven indicator light will glow until the oven has

reached the temperature selected (Fig. 2.22). It will then cycle on and o during cooking.

ArtNo.331-0002 Grill pan high/low position

ArtNo.331-0001Grill pan pulled forwards

ArtNo.270-0004

Proplus grill control

ArtNo.270-0005 Proplus

electric oven control

140

100

180

220

ArtNo.270-0006 Proplus

oven control light

140

100

180

220

ArtNo.330-0003 - Grill pan w handle pulled forwards

Fig. 2.17

Fig. 2.18

Fig. 2.19

Fig. 2.20

Fig. 2.21 Fig. 2.22

Accessories

Oven Shelves – Left-hand (Main) Oven

The oven shelves (Fig. 2.23) are retained when pulled forward but can be easily removed and retted.

Pull the shelf forward until the back of the shelf is stopped by the shelf stop bumps in the oven sides (Fig. 2.24).

Lift up the front of the shelf so the back of the shelf will pass under the shelf stop and then pull the shelf forward (Fig. 2.25).

To ret the shelf, line up the shelf with a groove in the oven side and push the shelf back until the ends hit the shelf stop. Lift up the front so the shelf ends clear the shelf stops, and then lower the front so that the shelf is level and push it fully back (Fig. 2.26).

Oven Shelves – Right-hand (Tall) Oven

The tall oven is supplied with four at cooking shelves

(Fig. 2.27), and a plate-warming shelf (Fig. 2.28).

Please note: The Hi-LITE does not have a plate warming shelf,

but is supplied with three at cooking shelves.

When using the tall oven, you can cook on all four shelves at the same time, but make sure that they are well spaced out to allow the hot air to circulate.

The Handyrack (Main Oven)

The Handyrack (Fig. 2.29) ts to the left-hand oven door only. Food cooking on it is easy to attend to, because it is accessible when the door is open.

The maximum weight that can be held by the Handyrack is 5.5 kg (12 lb). It should only be used with the supplied roasting tin, which is designed to t the Handyrack. Any other vessel could be unstable.

It can be tted at two dierent heights. One of the oven shelves must be removed and the other positioned to suit.

When the Handyrack is used in its highest position, other dishes can be cooked on the bottom shelf position or base of the oven.

When the Handyrack is used in its lowest position, other dishes can be cooked on the second shelf position or base of the oven.

To t the Handyrack, locate one side of it on the door bracket (Fig. 2.30). Then spring the other side out to clip it onto the other bracket (Fig. 2.31).

ArtNo.324-0002 Oven shelf

ArtNo.320-0015

Fitting the Handyack 1

ArtNo.320-0016

Fitting the handyrack 2

ArtNo.320-0011 Removing the shelf 1

ArtNo.320-0012 Removing the shelf 2

Shelf guard

Front

ArtNo.324-0010 Plate warming shelf

Fig. 2.23

Fig. 2.24

Fig. 2.26

Fig. 2.28

Fig. 2.30

Fig. 2.25

Fig. 2.27

Fig. 2.29

Fig. 2.31

ArtNo.300-0005 2BC minute minder setting

A B

ArtNo.300-0005 2BC minute minder setting

A B

C D

The clock must be set to the time of day before the oven will work.

Setting the Clock

1. Once the cooker is connected and switched on, the

display will start to ash.

2. To set the time, turn the Timer (A) knob to the Clock (C)

setting and back to the Manual (D) position. The centre dot will ash indicating the time can be set. Turn the

Adjusting (B) knob either clockwise or counter-clockwise (Fig. 3.1) to set the time.

3. Once you have set the time, allow the centre dot to stop

ashing, the time is now set.

Setting the Minute Minder

A Minute Minder (E) is a feature that can be set for a number of minutes and sounds an alarm once the specied amount of time has elapsed.

1. Turn the Timer (A) knob to the Minute Minder (E)

setting – it should click into position (Fig. 3.2).

2. Turn the Adjusting (B) knob to set the amount of time

required. Minimum time 1 minute (Fig. 3.3).

3. Turn the Timer (A) knob back to the Manual (D) setting

to see the current time and the ‘Bell’ symbol on the display.

Cancel the Timer Alarm

Once the specied time has elapsed it will emit an alarm. There are two ways to cancel the alarm:

1. Turn the Adjusting (B) knob counter-clockwise or

clockwise (Fig. 3.4).

2. Turn the Timer (A) knob to the Clock (C) or the Minute

Minder (E) setting, and back to the Manual (D) mode, to return to normal cooking (Fig. 3.4).

NOTE

If the alarm is not manually switched o it will stop after

approximately 2 minutes.

When the Minute Minder is active the clock will not dim

between the hours of 10 pm and 6 am

ArtNo.301-0007 2BC

Stopping the oven 1

A B

Fig. 3.1

A – Timer knob, B – Adjusting knob

Fig. 3.2

Fig. 3.3

Fig. 3.4

3. The Clock

A B

ArtNo.311-0004 RShaw

2BC stoppingOven 1

A B

To Stop the Oven at a Speciﬁc Time of Day

You have set the required temperature and function mode and you would like the oven to automatically stop.

TOP TIP

Make a note of the current time so you do not forget.

1. Turn the Timer (A) knob to the Stop Time (G) setting. ‘AUTO’ will show in the display (Fig. 3.5).

2. Turn the Adjusting (B) knob to the amount of cooking

time required. The display will show the current time plus the additional cooking time you have set (Fig. 3.6).

3. Turn the Timer (A) knob to the Auto (H) setting. The display will show the current time, the cooking symbol and the word ‘AUTO’ (Fig. 3.7).

4. Once the specied time has elapsed it will emit an alarm and the oven will stop working. The cook pot symbol on the display will disappear and the word ‘AUTO ’ will ash

(Fig. 3.8).

5. When you return, turn the Timer (A) knob to the Manual (D) setting to return to manual cooking (Fig. 3.8).

TOP TIP

You can check how much time you have left, to the

programmed stop time, by turning Timer (A) from Auto (H) to

Stop Time (G) and back to Auto (H)

A B

Fig. 3.5

Fig. 3.6

Fig. 3.7

Fig. 3.8

A B

To Start and Stop the Oven Automatically

The timer allows you to automatically start and stop by a combination of the length of the cooking time and the stop time. Giving you the exibility to cook casseroles etc while you are out. You cannot set the actual start time.

1. Turn the Timer (A) knob to the Cook Time (F) setting. Turn the Adjusting (B) knob clockwise to set the length of the cooking time required (Fig. 3.9).

2. Turn the Timer (A) knob to the Stop Time (G) setting (Fig. 3.10). The display will show the current time of day

plus the ‘cook time’ you just set.

3. Turn the Adjusting (B) knob to set the time of day you want the oven to stop cooking (Fig. 3.11).

4. Set the oven to the required cooking temperature and function mode.

5. Turn the Timer (A) knob to the Auto (H) setting (Fig. 3.12). If the display shows the current time and the word ‘AU TO’ the oven is set to turn on and o.

6. When the program starts the oven, the cooking symbol

will appear on the display. Once the specied time has elapsed it will emit an alarm and the Multifunction Oven will stop working. The ‘Cooking’ symbol on the display will disappear and the word ‘AUTO ’ will ash (Fig. 3.13).

7. Once the specied time has elapsed it will emit an alarm. There are two ways to cancel the alarm, refer to “Cancel

the Timer Alarm” on page 8

• The ‘cook period’, which is the length of time you want the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

Reset to Manual Cooking

To cancel any automatic settings turn the Timer (A) knob to the Manual (D) setting and release (Fig. 3.14).

Note: Whilst this operation cancels all automatic program settings, it does not cancel the minute minder.

Beeper Tone Adjustment

The beeper tone can be adjusted to three dierent levels.

Turn the Timer (A) knob to the Clock (C) setting. Turn the Adjusting (B) knob counter clockwise until the tone bars are displayed (Fig. 3.15).

To adjust the tone of the alarm, release the Adjusting (B) knob and then turn counter clockwise again (Fig. 3.16). The tone of the alarm will change. Repeat these steps until the desired alarm tone is set.

A B

Fig. 3.9

Fig. 3.10

Fig. 3.11

A B

Fig. 3.12

Fig. 3.13

Fig. 3.14

Fig. 3.15 Fig. 3.16

The 6-button Clock

You can use the timer (Fig. 3.17) to turn the oven(s) on and o. The clock must be set to the time of day before the oven(s) will work.

Table 3.1 describes the symbols shown on the digital display.

Setting the Time of Day

When the cooker is rst connected to the mains, or if there has been a prolonged power interruption, the clock display ashes [ 0.00 ] and [AUTO].

During the time setting process the centre dot will ash. When the process is complete the dot will stop ashing and the [] symbol will be displayed.

The time of day can be set in two ways:

• Press and hold the [] button. Now press the [+] or [-] buttons to increase or decrease the time (Fig. 3.18). Holding the [+] or [-] buttons for more than 2 seconds will advance / decrease the set time quickly. Release the buttons to set the time of day.

• Press and hold both the [] and [] buttons down (Fig. 3.19). Now press the [+] button (or [–] button) until the correct time shows.

Do not forget that it is a 24-hour clock.

If you need to reset the clock/cooker, turn o the power and wait several minutes, then start again.

Automatic Dimming

Providing there are no automatic programs set, and the minute minder is not active, your clock will automatically dim during the hours between 22:00 and 06:00.

Minute Minder

Press and hold the [] button (Fig. 3.20), and then press the [+] button (or [–] button) until the length of time you want to cook for is shown (Fig. 3.21).

You can check the time remaining by pressing []. When the beeper sounds cancel it by pressing any button.

• The ‘cook period’, which is the length of time you want the oven to cook for.

• The ‘stop time’, which is the time of day you want the oven to stop cooking.

Setting a Cook Duration

Press and hold the [] button and set the required ‘cook period’ by pressing the [+] button (or [–] button) (Fig. 3.22).

The clock will now control the cook period of your oven(s). The [] symbol and [AUTO] will be displayed.

Once the ‘cook period’ is reached, the beeper sounds and the [AUTO] symbol ashes. Turn the oven control knob to 0 and then press any button to stop the beep. Press [] to return to manual cooking.

ArtNo.302-0002 - 6BC annotated

A B C D E F

A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time, D – Manual,

E & F – Time setting buttons

Fig. 3.17

Fig. 3.18 Fig. 3.19

Fig. 3.20 Fig. 3.21

Fig. 3.22

Symbol Function Notes

[]

Minute Minder is active

[]

Oven(s) can be operated

If the ‘cook’

[] symbol is not

displayed the program has either:

• ended and the oven(s) are nonoperational

• the oven(s) are being controlled by an automatic program that

has not started

[AUTO]

Oven(s) are being

controlled in

semi-automatic or

automatic mode

[P]

Self clean (pyrolytic)

mode has been enabled

Your cooker may not have this

pyrolytic function

[dot]

Flashes during setting

the time of day

Table 3.1

ArtNo.302-0002 - 6BC annotated

Setting a Cook End Time

Press and hold the ‘stop time’ [] button (Fig. 3.23) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig. 3.24). The [] symbol and [AUTO] will show in the display.

Once the ‘stop time’ is reached, the beeper sounds and the [AUTO] symbol ashes. Turn the oven control knob to 0 and then press any button to stop the beep. Press [] to return to manual cooking.

To Start and Stop the Ovens Automatically

Before you set the clock for automatic operation you must have two numbers clearly in mind – the ‘cook period’ and the ‘stop time’.

Note: You cannot set a start time directly – this is set automatically by setting the ‘cook period’ and the ‘stop time’.

Press and hold the [] button (Fig. 3.25) and then press the [+] button (or [–] button) until the required ‘cook period’ shows (Fig. 3.26).

Now press and hold the [] button (Fig. 3.27) and then press the [+] button (or [–] button) until the required ‘stop time’ shows (Fig. 3.28). Release the buttons.

[AUTO] will now show in the display (Fig. 3.29).

Set the oven(s) to the required temperature. When cooking is nished [AUTO] will ash and the beeper will sound. Turn the oven knob(s) to the OFF position rst, and then press any button once to stop the beep; press the [] button to return to manual cooking.

If you are out, do not worry about the beeper going o, it stops after a while. When you return, turn the oven knob(s) to 0 rst, and then press [] to return to manual cooking.

AUTO is Showing, You Want to Reset to Manual Cooking

To return to manual cooking mode from an Automatic setting, simultaneously press the [+] and [-] key, this will clear the automatic program and return to manual mode.

Please note that this action will also clear the [Minute Minder] setting.

For an overview of the functions refer to Table 3.2.

Fig. 3.23 Fig. 3.24

Fig. 3.25 Fig. 3.26

Fig. 3.27 Fig. 3.28

Fig. 3.29

Symbol Function Notes

[]

Sets the Minute Minder Used with the [+] and [-] buttons

[]

Sets the duration / cook

period

Used with the [+] and [-] buttons

[]

Sets the end / stop cook

time

Used with the [+] and [-] buttons

[ ]

[] & []

Allows the time of day to be set when ‘AUTO’ is not

active

Used with the [+] and [-] buttons

[ ]

Resets the cooking

control to manual

[ - ]

Decreases time interval

Holding this button down

allows a quick set

[ + ]

Increases time interval

Holding this button down

allows a quick set

[ + ] & [ - ]

Clears all ‘AUTO’ and

minute minder programs

Table 3.2

Tips on Cooking with the Timer

If you want to cook more than one dish, choose dishes that require approximately the same cooking time. However, dishes can be ‘slowed down’ slightly by using small containers and covering them with aluminium foil, or ‘speeded up’ slightly by cooking smaller quantities or placing them in larger containers.

Very perishable foods such as pork or sh should be avoided if a long delay period is planned, especially in hot weather.



DO NOT place warm food in the oven to be timed.



DO NOT use a timed oven that is already warm.



DO NOT use the timed oven if the adjoining oven is already warm.

Whole poultry must be thoroughly defrosted before being placed in the oven. Check that meat and poultry are fully cooked before serving.

General Oven Tips

The wire shelves should always be pushed rmly to the back of the oven.

Baking trays with food cooking on them should be placed level with the front edge of the oven’s wire shelves. Other containers should be placed centrally. Keep all trays and containers away from the back of the oven, as overbrowning of the food may occur.

For even browning, the maximum recommended size of a baking tray is 340 mm (13½”) by 340 mm (13½”) in the main oven and 232 mm (91/8”) by 321 mm (125/8”) in the tall oven.

When the oven is on, do not leave the door open for longer than necessary, otherwise the knobs may get very hot.

• Always leave a “finger’s width” between dishes on the same shelf. This allows the heat to circulate freely around them.

• To reduce fat splashing when you add vegetables to hot fat around a roast, dry them thoroughly or brush lightly with cooking oil.

• Where dishes may boil and spill over during cooking, place them on a baking tray.

• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your Cooker’) work better when fat splashes are avoided. Cover meat when cooking with foil or use a roasting bag.

• Sufficient heat rises out of the oven while cooking to warm plates in the grill compartment.

• If you want to brown the base of a pastry dish, preheat the baking tray for 15 minutes before placing the dish in the centre of the tray.

4. Cooking Tips

5. Cooking Table

ArtNo.050-0007

Oven shelf positions

Oven Shelf Positions

Top (T)

Centre (C)

Base (B)

The oven control settings and cooking times given in the table below are intended to be used AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a preferred result.

Food is cooked at lower temperature in a fan oven than in a conventional oven. When using recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The temperature in the fan oven does not vary with height in the oven so you can use any shelf.

Food

Meat

Beef (no bone)

Lamb

Pork

Poultry

Chicken

Turkey

Duck

Casserole

Yorkshire Pudding

Cake

Very rich fruit - Christmas,

wedding, etc.

Fruit 180 mm tin

Fruit 230 mm tin

Madeira 180 mm

Small cakes

Scones

Victoria sandwich

180 mm tin

210 mm tin

Desserts

Shortcrust tarts

Fruit pies

Tartlets

Puff pastry

Meringues

Baked egg custard

Baked sponge pudding

Milk pudding

Bread

Fish

Fillet

Whole

Steak

Approximate Cooking Time

30-35 minutes per 500g +30-35 minutes.

20-25 minutes per 500g +20-25 minutes.

30-35 minutes per 500g +30-35 minutes.

25-30 minutes per 500g +25-30 minutes.

35-40 minutes per 500g +35-40 minutes.

25-30 minutes per 500g +25-30 minutes.

20-25 minutes per 500g +20-25 minutes.

15-20 minutes per 500g +15-20 minutes.

20 minutes per 500g +20 minutes.

15 minutes per 500g +15 minutes.

25-30 minutes per 500g.

20 minutes per 500g.

2-4 hours according to recipe.

Large tins 30-35 minutes; individual 10-20 minutes.

45-50 minutes per 500g of mixture.

2-2½ hours.

Up to 3½ hours.

80-90 minutes.

15-25 minutes.

10-15 minutes.

20-30 minutes.

30-40 minutes.

20-30 minutes on a preheated tray.

35-45 minutes.

10-20 minutes according to size.

20-40 minutes according to size.

2-3 hours.

45-60 minutes.

40-45 minutes.

2 to 3 hours.

20-30 minutes.

15-20 minutes.

15-20 minutes per 500g.

Steaks according to thickness.

Conventional Oven

Temperature °C

(Shelf Position)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

160 (C)

200 (C)

140-150 (C)

220 (C)

140 (C/B)

150 (C/B)

160 (C/B)

170 (C/B)

200 (C/B)

170 (C/B)

200 (C/B)

180 (C/B)

210 (C/B)

100 (C/B)

160 (C/B)

180 (C/B)

140-150 (C/B)

210 (C)

Fanned Grilling

190 (C/B)

Fan Oven

Temperature

°C

150

190

150

190

150

190

150

190

150

190

150

190

130-140

210

130

140

150

160

190

160

190

170

200

150

170

130-140

200

190 (C/B)

Thoroughly thaw frozen joints before cooking. Meat may be roasted at 220°C (210°C for fan oven) and the cooking time adjusted accordingly. For stuffed and rolled meats, add approximately 10 minutes per 500g, or cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for the remainder.

For stuffed poultry, you could cook at 200°C (190°C) for 20 minutes then 160°C (150°C) for remainder. Do not forget to include the weight of the stuffing. For fresh or frozen prepacked poultry, follow instructions on the pack. Thoroughly thaw frozen poultry before cooking.

Using the conventional oven: when two tier cooking leave at least one runner space between shelves. Position the baking tray with the front edge along the front of the oven shelf.

ArtNo.050-0001 Gas cooking table

Using the conventional oven: for even browning the maximum size of baking tray recommended is 340 mm x 340 mm. This ensures free heat circulation. If cooking a two tier load, the trays should be interchanged approximately halfway though the cooking time.

Up to three tiers can be cooked in a fan oven at the same time but make sure to leave at least one runner space between each shelf being cooked on.

T - Top; C - Centre; B - Base

DocNo.031-0004 - Cooking table - electric & fan single cavity

ArtNo.311-0032 Burner layout FSD

ArtNo.311-0033 Wok burner details FSD

ArtNo.311-0016 Fitting the burner inner head

A – Cap, B – Head, C – Notch, D – Base , E – Electrode

A – Inner burner cap, B – Outer burner cap, C – Inner burner head, D

– Outer burner head, E – Wok burner base

A – Electrode notch, B – Ignition electrode

Essential Information

Isolate the electricity supply before carrying out any thorough cleaning. Allow the cooker to cool.



NEVER use paint solvents, washing soda, caustic cleaners, biological powders, bleach, chlorine based bleach cleaners, coarse abrasives or salt.



DO NOT mix dierent cleaning products – they may react together with hazardous results.

All parts of the cooker can be cleaned with hot soapy water – but take care that no surplus water seeps into the

appliance.

Remember to switch on the electricity supply and reset the clock before re-using the cooker.

Hotplate Burners

The burner heads and caps can be removed for cleaning.



DO NOT put the burner heads in a dishwasher.

Make sure they are absolutely dry before replacing them.

The Single Ring Burners

When retting the burner head, make sure that the notch lines up with the electrode or hole in the base. Check that the burner head is level and that the cap is tted centrally on the burner head (Fig. 6.1).

The Wok Burner

The Wok burner can also be taken apart for cleaning.

When reassembling the wok burner (Fig. 6.2), turn over the large base ring and nd the ‘D’ shaped area (Fig. 6.3). Turn the head until the ‘D’ matches the one on the burner base. Flip the burner over once again and place it on the burner base.

To t the small inner burner, nd the larger electrode notch in the burner rim. Line this up with the white ignition electrode and place the inner burner on the large base ring (Fig. 6.4).

Now t the two burner caps, making sure that they are seated properly.

Check the burner ports are not blocked. If a blockage occurs, remove stubborn particles using a piece of fuse wire.

The Wok Cradle

Recommended cleaning materials are hot soapy water, a moistened soap pad, cream cleaner or a nylon scourer.

The Griddle

Always clean the griddle after use. Allow it to cool completely before removing. Immerse the griddle plate in hot soapy water. Use a soft cloth or, for stubborn stains, a nylon washing up brush.

Note: If the griddle is washed in a dishwasher then some dishwasher residue may appear on the back. This is normal and will not aect the performance of your griddle.

6. Cleaning Your Cooker

Fig. 6.1

Fig. 6.2

Fig. 6.3

Fig. 6.4

ArtNo.331-0001Grill pan pulled forwards

ArtNo.331-0003 Grill frame out, no pan

ArtNo.331-0004 Removing the grill frame

ArtNo.331-0005 Removing the grill rail

ArtNo.331-0006 Grill pan plan

Grills

The grill pan and trivet should be washed in hot soapy water. After grilling meats or any foods that soil, leave to soak for a few minutes immediately after use. Stubborn particles may be removed from the trivet using a nylon brush. Alternatively, the grill pan can be washed in a dishwasher.



Before you remove any of the grill parts for cleaning, make sure that they are cool, or use oven gloves.



DO NOT use any abrasive substances.

Cleaning the Glide-out Grill

The grill pan can be easily removed for cleaning as follows:

Remove the grill pan support frame by pulling the grill pan forward (Fig. 6.5).

Lift the grill pan clear of the support frame.

The support frame

is held to the side rails by two clips on each side (Fig. 6.6).

For each side, support the side rail with one hand and with the other hand lift the frame up and out of the side clips (Fig.

6.7).

For safety, push the side rails back into the grill chamber.

If you need to remove the side rails to allow cleaning of the grill chamber, you can unhook them from the grill chamber sides (Fig. 6.8) and wipe the sides clean with a soft cloth and mild detergent.



DO NOT put the side runners in a dishwasher.

Once you have nished, hook the side rails back onto the sides of the chamber. To ret the frame, pull the side rails forward and, for each side in turn, support the side rail and press the frame down into the side rails.

Ret the grill pan. When retting the grill pan, make sure that the wide rim is at the front (Fig. 6.9).

Control Panel and Doors

Avoid using any abrasive cleaners including cream cleaners. For best results, use a liquid detergent.

The same cleaner can be used on the doors, or alternatively, using a soft cloth wrung out in clean hot soapy water – but take care that no surplus water seeps into the appliance.

After cleaning, polish with a dry cloth.

Fig. 6.5

Fig. 6.6

Fig. 6.7

Fig. 6.8

Fig. 6.9

Glass Fronted Door Panels

The oven door front panels can be taken o so that the glass panels can be cleaned. Move the cooker forward to gain access to the sides (see the ‘Moving the Cooker’ section under ‘Installation’).

Open the oven door slightly and remove the front panel xing screws from the door sides, two each side (Fig. 6.10).

Carefully lift o the outer door panel. The inside face of the glass panels can now be cleaned – take care not to disturb or wet the door insulation.

Note: If the door is triple glazed then the inner two panels are xed together and should not be separated.

After cleaning, carefully ret the outer door panel and replace the side xing screws.



DO NOT use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass.

Ovens

‘Cook & Clean’ Panels

The main oven has panels which have been coated with a special enamel that partly cleans itself. This does not stop all marks on the lining, but helps to reduce the amount of manual cleaning needed.

The ‘Cook & Clean’ panels work better above 200 °C. If you do most of your cooking below this temperature, occasionally remove the panels and wipe with a lint free cloth and hot soapy water. The panels should then be dried and replaced and the oven heated at 200 °C for about one hour. This will make sure that the ‘Cook & Clean’ panels are working eectively.

DO NOT use steel wool, oven cleaning pads, or any other materials that will scratch the surface.

Removing the Main Oven Linings

Some of the lining panels can be removed for cleaning.

If you wish to clean the enamel interior of the oven, you will need to remove the shelves before removing the ‘Cook & Clean’ panels . You do not have to remove the support brackets to remove the panels. Lift each panel upward and slide forward o the support brackets (Fig. 6.11).

Once the panels have been removed, the oven enamel interior can be cleaned.

Ret in the reverse order.

The Tall Oven

To clean the oven sides, slide out the shelves, unhook the supports from the oven sides, and lift out (Fig. 6.12).

ArtNo.320-0002a Proplus oven door side screws

Fig. 6.10

Fig. 6.11

Fig. 6.12

Cleaning Table

Cleaners listed (Table 6.1) are available from supermarkets or electrical retailers as stated.

For enamelled surfaces use a cleaner that is approved for use on vitreous enamel.

Regular cleaning is recommended. For easier cleaning, wipe up any spillages immediately.

Table 6.1

Hotplate

Part Finish Recommended Cleaning Method

Hob top (including burner heads and caps)

Enamel, stainless steel, aluminium

Hot soapy water, soft cloth. Any stubborn stains remove gently with a nylon scourer.

Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.

Griddle plate (some models only) Non-stick surface

Allow to cool. Wash in hot soapy water. Do not use abrasive cleaners/scourers. Dishwasher.

Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Outside of Cooker

Part Finish Recommended Cleaning Method

Door, door surround and storage drawer exterior

Enamel or paint

Hot soapy water, soft cloth. Any stubborn stains, remove gently with a liquid detergent.

Stainless steel

E-cloth (electrical retailers) or microfibre all-purpose cloth (supermarket).

Sides and plinth Painted surface Hot soapy water, soft cloth.

Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.

Control panel

Paint, enamel, stainless steel or glass

Warm soapy water. Do not use abrasive cleaners on lettering.

Control knobs/handles & trims

Plastic/chrome, copper or lacquered brass

Warm soapy water, soft cloth.

Brass Brass polish.

Oven door glass/glass lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.

Oven and Grill

Part Finish Recommended Cleaning Method

Sides, floor & roof of oven NOT COOK & CLEAN OVEN PANELS (see below)

Enamel

Any proprietary oven cleaner that is suitable for enamel. CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW

MANUFACTURER’S INSTRUCTIONS. Do not allow contact with the oven elements.

Cook & Clean oven panels (some models only)

Special enamel that partly cleans itself

This surface cleans itself at 200 °C and above, or the panels can be removed and washed with hot soapy water and a nylon brush (see ‘The Ovens’ in ‘Cleaning your Cooker’).

Oven shelves, Handyrack, grill trivet, Handygrill rack

Chrome

An oven interior cleaner that is suitable for chrome. Soap filled pad. Dishwasher.

Grill pan/meat tin (some models only)

Enamel Hot soapy water. Soap filled pad. Dishwasher.

Hotplate ignition or hotplate burners faulty

Is the power on? Is the clock illuminated?

If not, there maybe something wrong with the power supply.

Are the sparker (ignition electrode) or burner slots blocked by debris.?

Are the burner trim and caps correctly located? See the section on ‘Cleaning’.

Hotplate burners will not light

Make sure that the burner parts have been replaced correctly after wiping or removing for cleaning.

Check that there is not a problem with your gas supply. You can do this by making sure that other gas appliances you may have are working.

Do the burners spark when you push the control?

If not, verify that the power is on by checking that the clock is illuminated.

Steam is coming from the oven

When cooking foods with high water content (e.g. oven fries) there may be some steam visible at the rear grille.

Take care when opening the oven door, as there may be a momentary pu of steam when the oven door is opened. Stand well back and allow any steam to disperse.

What cleaning materials are recommended for the cooker?

See the ‘Cleaning’ section for recommended cleaning materials.



Never use caustic or abrasive cleaners as these will damage the surface.

An oven fan is noisy

The note of the oven fan may change as the oven heats up – this is perfectly normal.

The knobs get hot when I use the oven or the grill. Can I avoid this?

Yes, this is caused by heat rising from the oven or the grill, and heating them up. Do not leave the oven door open.

Make sure that the grill pan is pushed right back to the ‘back stop’ when grilling.

Always grill with the grill compartment door open.

The fascia gets hot when I use the oven or grill

The cooker is cooled by a fan. If the fascia becomes excessively hot when the cooker is in use then the cooling fan may have failed. Should this occur please contact your installer, a qualied repair engineer or Customer Service to arrange for its repair.

If there is an installation problem and I don’t get my original installer to come back to x it who pays?

You do. Service organizations will charge for their call outs if they are correcting work carried out by your original installer. It is in your interest to track down your original installer.

Power failure

In the event of a failure in the electrical supply, remember to reset the clock to make sure that the timed oven continues to operate.

Fascia illumination is not coming on (Hi-LITE only)

Is the power on?

The appliance has developed a fault that cannot be rectied by the user. Please contact your installer or a qualied repair engineer.

Food is cooking too slowly, too quickly, or burning

Cooking times may dier from your previous oven.

Check that you are using the recommended temperatures and shelf positions – see the oven cooking guide. The oven control settings and cooking times are intended to be used only as a guide.

Individual tastes may require the temperature to be altered either way, to get the results you want.

The oven is not cooking evenly

Do not use a baking tray with dimensions larger than those specied in the section on ‘General Oven Tips’.

If you are cooking a large item, be prepared to turn it round during cooking.

If two shelves are used, check that space has been left for the heat to circulate. When a baking tray is put into the oven, make sure that it is placed centrally on the shelf.

Check that the door seal is not damaged and that the door catch is adjusted so that the door is held rmly against the seal.

A dish of water when placed on the shelf should be the same depth all over. (For example, if it is deeper at the back, then the back of the cooker should be raised up or the front lowered.) If the cooker is not level arrange for your supplier to level it for you.

Oven not coming on

Is the power on? Is the clock illuminated? If not, there may be something wrong with the power supply.

Is the cooker supply on at the isolator switch?

Has the time of day been set?

Is the key symbol [



] showing in the display to signify that the oven is locked? See the ‘Clock’ section of the instructions for more information on the key lock feature.

7. Troubleshooting

The timed oven is not coming on when automatic cooking

Has the oven knob been left in the OFF position by mistake?

Is the oven locked (see above)?

Oven temperature getting hotter as the cooker gets older

If turning the temperature down using the oven control knob has not worked, or has only worked for a short time, then you may need a new thermostat. This should be tted by a service person.

An oven light is not working

The bulb has probably burnt out. You can buy a replacement bulb (which is not covered under the warranty) from a good electrical shop. Ask for a 15 W – 230 V lamp, FOR OVENS. It must be a special bulb, heat resistant to 300 °C (Fig. 7.1).

Turn o the power at the circuit breaker.

Before removing the existing bulb, turn o the power supply and make sure that the oven is cool. Open the oven door and remove the oven shelves.

Unscrew the bulb cover by turning counter-clockwise. It may be very sti (Fig. 7.2).

Taking care to protect your ngers with a glove in case the bulb should shatter, unscrew the old bulb.

Screw in the new bulb; screw back the bulb cover. Turn on the circuit breaker and check that the bulb now lights.

The oven door is misaligned

The bottom hinge of either oven door can be adjusted to alter the angle of the door (Fig. 7.3). Loosen the bottom hinge xing screws and use the notch and a at bladed screwdriver to move the position of the hinge to set the hinge position (Fig. 7.4).

Retighten the hinge screws.

ArtNo.324-0005 Oven light bulb

ArtNo.320-0007 Oven door hinge adjustment 2

Eect of hinge adjustment – exaggerated for clarity

Oven door omitted for clarity

Centreline of hinge pin

Fig. 7.1

Fig. 7.2

Fig. 7.3

Fig. 7.4

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Dear Installer

Before you start your installation, please complete the details below, so that, if your customer has a problem relating to your installation, they will be able to contact you easily.

Safety Requirements and Regulations



This cooker must be installed in accordance with the relevant instructions in this booklet, with the relevant national and local regulations, and with the local gas and electricity supply companies’ requirements.



This cooker is a Class 2 Subclass 1 appliance.



Before installation, make sure that the cooker is suitable for your gas type and supply voltage. See the data badge.



The appliance must be installed in accordance with the regulations in force and only in a well-ventilated space.



Read the instructions before installing or using this appliance.



In your own interest and that of safety, it is law that all gas appliances be installed by competent persons. Failure to install the appliance correctly could invalidate any warranty or liability claims and lead to prosecution.



This appliance can be converted for use on another gas.

In the UK the cooker must be installed in accordance with:

• All relevant British Standards / Codes of Practice, in particular BS 5440 Part 2.

• For Natural Gas – BS 6172 and BS 6891.

• For LP Gas – BS 5482-1 (when the installation is in a permanent dwelling), BS 5482-2 (when the installation is in a caravan or other non-permanent dwelling) or BS 5482-3 (when the installation is in a boat).

• The Gas Safety (Installation and Use) regulations.

• The relevant Building / IEE regulations.

In the Republic of Ireland the cooker must be installed in accordance with:

The installation must be carried out by a competent person and installed in accordance with the current edition of IS 813 “Domestic Gas Installations”, the current Building Regulations and reference should be made to the current ETCI rules for electrical installation.

Provision of Ventilation

This appliance is not connected to a combustion products evacuation device. Particular attention shall be given to the relevant requirements regarding ventilation.

All rooms require a window that can be opened, or equivalent, while some rooms require a permanent vent in addition to the window.

In the UK:

The room containing the cooker should have an air supply in accordance with BS 5440 Part 2. All rooms require an openable window or equivalent, while some rooms require a permanent vent in addition to the openable window. The cooker should not be installed in a bedsitting room with volume less than 20 m³. If it is installed in a room of volume less than 5 m³ an air vent of eective area 100 cm² is required; if it is installed in a room of volume between 5 m³ and 10 m³, an air vent of eective area 50 cm² is required; while if the volume exceeds 11 m³, no air vent is required.

If there are other fuel burning appliances in the same room, BS 5440 Part 2 should be consulted to determine the requisite air vent requirements.

In the Republic of Ireland:

Reference should be made to the current edition of IS 813, which makes clear the conditions that must be met to demonstrate that sucient ventilation is available.

ArtNo.050-0011 - Installer information table

Installer’s Name

Appliance Serial Number

Installer’s Telephone Number

Installer’s Company

8. Installation

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Checking the Parts:

Location of Cooker

The cooker may be installed in a kitchen/kitchen diner but NOT in a room containing a bath or shower.

This appliance is designed for domestic cooking only. Use for any other purpose could invalidate any warranty or liability claim.

Note: An appliance for use on LPG must not be installed

in a room or internal space below ground level, e.g. in a basement.

Conversion

This appliance is supplied set for G20 20 mbar Cat II

2H3+

A conversion kit for another gas is available for the cooker.

If the appliance is to be converted to another gas we recommend that this is carried out before installation.

After converting the appliance, please attach the Gas Conversion sticker over the appropriate area of the data badge – this will identify the gas type for which the appliance is now set.

You will need the following equipment to complete the cooker installation satisfactorily:

• Stability bracket: If the cooker is to be supplied with gas through a flexible hose, a stability bracket or chain MUST be fitted. These are not supplied with the cooker but are available at most builders’ merchants.

• Gas pressure tester/manometer.

• Flexible gas hose: Must be in accordance with the relevant standards.

• Multimeter: For electrical checks.

You will also need the following tools:

1. Electric drill

2. Masonry drill bit (only required if tting the cooker on a

stone or concrete oor)

3. Wall plugs (only required if tting the cooker on a stone or concrete oor)

4. Steel tape measure

5. Cross head screwdriver

6. Flat head screwdriver

7. Spirit level

8. Pencil

9. Adjustable spanner

10. Screws for tting the stability bracket

11. 4 mm & 3 mm Allen keys

12. 13 mm spanner or socket wrench

3 pan supports Griddle

ArtNo.000-0001 90 Pan supports

Plinth (1-piece model shown) Grill pan & trivet

ArtNo.330-0001 - Grill pan

4 at shelves Roasting tin

ArtNo.324-0004 Roasting tin

Handyrack

Tall oven shelves and shelf

supports (example shown)

ArtNo.324-0003 Handyrack

ArtNo.000-0010 Tall oven shelves

Splashback (Classic only)

ArtNo.350-0012 - splashback

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

ArtNo.105-0008 - 100DF 2BC cooker min spacings

Professional +

905 mm min 930 mm max

75 mm

min

75 mm

min

650 mm

min

130 mm min

Positioning the Cooker

Fig. 8.1 and Fig. 8.2 show the minimum recommended distance from the cooker to nearby surfaces.

The cooker should not be placed on a base.

Above hotplate surround should be level with, or above, any adjacent work surface.

A gap of 75 mm should be left between each side of the cooker ABOVE the hotplate level and any adjacent vertical surface.

For non-combustible surfaces (such as unpainted metal or ceramic tiles), this can be reduced to 25 mm.

A minimum space of 650 mm is required between the top of the hotplate and a horizontal combustible surface.

*Any cookerhood should be installed in accordance with the hood manufacturer’s instructions.

**Any splashback must be tted in accordance with the manufacturers instructions. Allowance should be made for the additional height of the ue trim, which is tted to the cooker hob.

Surfaces of furniture and walls at the sides and rear of the appliance should be heat, splash and steam resistant. Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage and discolouration.

We cannot accept responsibility for damage caused by normal use of the cooker to any material that de-laminates or discolours at temperatures less than 65 °C above room temperature.

We recommend a gap of 1010 mm between units to allow for moving the cooker. Do not box the cooker in – it must be possible to move the cooker in and out for cleaning and servicing.

If the cooker is near a corner of the kitchen, a clearance of 130 mm is required to allow the oven doors to open (Fig. 8.3). The actual opening of the doors is slightly less but this allows for some protection of your hand as you open the door.

Moving the Cooker



On no account try and move the cooker while it is plugged into the electricity supply.



The cooker is very heavy, so take great care.

We recommend that two people manoeuvre the cooker. Make sure that the oor covering is rmly xed, or removed, to prevent it being disturbed when moving the cooker around.

To help you, there are two levelling rollers at the back, and two screw-down levelling feet at the front.

Remove the polystyrene base pack. From the front, tilt the cooker forward and remove the front half of the polystyrene base (Fig. 8.4). Repeat from the back and remove the rear half of the polystyrene base.

ArtNo.105-0009-100DF-2BC Min distances above cooker

1000 mm min*

410 mm min

5 mm5 mm

Fig. 8.1

Fig. 8.2

Fig. 8.3

Fig. 8.4

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

ArtNo.070-0014 - Stability bracket - Wall fitting

Cooker

Stability bracket

Floor

3 mm min

Typical oor mounting

Typical oor mounting

Cooker

Outer stability

bracket

Floor

Wall

3 mm min

Typical wall mounting

Stability chain

ArtNo.010-0004 Moving the cooker

Lowering the Two Rear Rollers

To adjust the height of the rear of the cooker, rst t a 13 mm spanner or socket wrench onto the hexagonal adjusting nut (Fig. 8.5). Rotate the nut – clockwise to raise – counterclockwise to lower.

Make 10 complete (360°) turns clockwise.

Make sure you lower BOTH REAR ROLLERS.

Completing the Move

Unfold the rear edge of the pack base tray. Open the grill door and right-hand oven door so that you can get a good grip on the bottom of the fascia panel as you move the oven (Fig. 8.6).

Carefully push the cooker backwards o the cardboard base. Remove the pack base tray.

Position the cooker close to its nal position, leaving just enough space to get behind it.



Do not use the door handles or control knobs to manoeuvre the cooker.

Fitting the Stability Bracket or Chain

Unless otherwise stated, a cooker using a exible gas connector must be secured with a suitable stability device.

Suitable stability devices are shown in Fig. 8.7, Fig. 8.8 and Fig. 8.9.

If you are using a stability chain (Fig. 8.7) then the chain should be kept as short as is practicable and xed rmly to the rear of the cooker.

If you are using a stability bracket (Fig. 8.8) and (Fig. 8.9), then adjust the bracket to give the smallest practicable clearance between the bracket and the engagement slot in the rear of the cooker.

Fit the bracket so that it engages as far as possible over the chassis of the cooker.

Repositioning the Cooker Following Connection

If you need to move the cooker once it has been connected then you need to unplug it and, having gripped under the fascia panel and lifted the front of the cooker slightly (Fig. 8.6), you need to check behind the cooker to make sure that the gas hose is not caught.

As you progress, make sure that both the electricity cable and gas hose always have sucient slack to allow the cooker to move.

With a stability chain tted, release it as you ease the cooker out. Do not forget to ret it when you replace the cooker.

When you replace the cooker, again check behind to make sure that the electricity cable and gas hose are not caught or trapped.

Fig. 8.5

Fig. 8.6

Fig. 8.7

Fig. 8.8

Fig. 8.9

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Conversion to Another Gas

If the appliance is to be converted to another gas do the conversion at this point. See the conversion section of these instructions.

Levelling

You are recommended to use a spirit level on a shelf in one of the ovens to check for level.

Place the cooker in its intended position, taking care not to twist it within the gap between the kitchen units as damage may occur to the cooker or the units.

The front feet and rear rollers can be adjusted to level the cooker.

To adjust the height of the rear of the cooker use a 13 mm spanner or socket wrench to turn the adjusting nuts at the front bottom corners of the cooker.

To set the front, turn the feet bases to raise or lower.

Gas Connection

This must be in accordance with the relevant standards.

The exible hose (not supplied with the cooker) must be in accordance with the relevant standards. Hoses may be purchased at most builders’ merchants.

We recommend that a Micropoint gas hose is used when installing this appliance.

The gas supply needs to terminate with a side-facing elbow with a down-facing bayonet.

The connector is located just below the hotplate level at the rear of the cooker. If in doubt contact your supplier.

The rear cover boxes limit the position of the supply point.

Because the height of the cooker can be adjusted and each connection is dierent, it is dicult to give precise dimensions.

Although a 900 mm hose can be used (on the Hi-LITE model we recommend a 1250 mm hose), a 1250 mm hose will allow slightly more exibility in the positioning of the bayonet and make moving the cooker easier.

The hose should be tted so that both inlet and outlet connections are vertical so that the hose hangs downwards in a ‘U’ shape.

Ideally the hose supply connection should be within the shaded area ‘A’ (Fig. 8.10 or Fig. 8.11 on Hi-LITE & Classic models).

For Natural Gas, the exible hose must be in accordance with BS 669. For LP Gas, it should be capable of 50 mbar pressure and a 70 °C temperature rise. If in doubt contact, your supplier.

Screw connect the threaded end of the hose into the gas inlet.

After completing the gas connection, make sure that the cooker is gas sound with a pressure test.

680

450

750

500

All dimensions in millimetres

Gas inlet

290

130

370

140

225

Gas inlet

All dimensions in millimetres

Fig. 8.10

Fig. 8.11

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

Pressure Testing

The gas pressure can be measured at one of the hotplate burner injectors (not the wok burner).

Lift o a burner head. Fit the pressure gauge to the injector. Turn on and light one of the other hotplate burners.

Turn on the control knob for the burner with the pressure gauge tted to let gas through.

See the data badge for test pressures.

Turn o the burners. Make sure that you reassemble the burner top in the correct way on the burner body.

Electrical Connection

The cooker must be installed by a qualied electrician, in accordance with all relevant British Standards/Codes of Practice (in particular BS 7671), or with the relevant national and local regulations.

Current Operated Earth Leakage Breakers

The combined use of your cooker and other domestic

appliances may cause nuisance tripping, so we

recommend that the cooker is protected on an individual

RCD (Residual Current Device) or RCBO (Residual Current

Breaker with Overload).

IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED

ELECTRICIAN.

Note: The cooker must be connected to the correct electrical

supply as stated on the voltage label on the cooker, through a suitable cooker control unit incorporating a double-pole switch, having a contact separation of at least 3 mm in all poles.



The cooker MUST NOT be connected to an ordinary domestic power point.

Access to the mains terminal is gained by removing the electrical terminal cover box on the back panel. Connect the mains cable to the correct terminals for your electrical supply type (Fig. 8.12 and Fig. 8.13). Check that the links are correctly tted and that the terminal screws are tight. Secure the mains cable using the cable clamp.

ArtNo.130-0010 Electrical connections single-phase

L N

230 V ac 50 Hz

10 mm² max

6 mm² max

N L3

3N ac 230/400 V 50 Hz

6 mm² max

10 mm² max

6 mm² max

Fig. 8.12

Fig. 8.13

INSTALLATION

Check the appliance is electrically safe and gas sound when you have nished.

ArtNo.350-0012 - Securing the plinth

Final Checks

Hotplate Check

Check each burner in turn (refer to the ‘Hotplate Burners’ section at the front of the instructions).

Grill Check

Turn on the grill control and check that the grill heats up.

Oven Check

Set the clock as described earlier in the instructions, and then turn on the ovens. Check that the oven fans start to turn and that the ovens start to heat up.

Note: The oven light bulb is not included in the guarantee.

Turn o the oven.

Fitting the Plinth

Fitting the 1-piece Plinth (Classic & Professional+)

Loosen the three screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and t each end keyhole over their respective screws. Tighten the xing screws (Fig. 8.14).

Fitting the 2-piece Plinth (Kitchener & Hi-LITE)

Fit the inner plinth to the bottom front of the cooker using the 4 or 5 screws provided (Fig. 8.15).

Kitchener: Fit the outer plinth (2 screws, 1 each end) to the inner plinth. The height of the outer plinth can be adjusted by sliding it up or down via the slotted hole (Fig. 8.16).

Hi-LITE: Oer the keyhole slots on the outer plinth to the location points on the inner plinth (Fig. 8.17)

When released the outer plinth should automatically adjust to the oor height (Fig. 8.17).



WARNING: When moving the cooker ensure that the outer plinth is removed. Failure to do so may result in damage to plinth and oor.

Customer Care

Installer: Please complete your details in this guide, inform the user how to operate the cooker and hand over the instructions.

Thank you.

ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)

ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)

Outer plinth

Outer plinth xing screw

Inner plinth

Fig. 8.14

Fig. 8.15

Fig. 8.16

Fig. 8.17

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

ArtNo.311-0010 Injectors

A – Jet, B – Internal injector, C – External injector

ArtNo.270-0032 - 90 Prof+ FX - Removing the control panel

Professional + 100 FX

Check the ‘Technical Data’ section at the back of the book that the hob is convertible to the gas you want to use.

A suitably competent person must perform the conversion. After conversion the installation must comply with the relevant regulations and also the local electricity supply company requirements. Read the instructions before converting this appliance.



Failure to convert the appliance correctly could invalidate any warranty or liability claims and lead to prosecution.



When servicing or replacing gas-carrying components disconnect from the gas supply before starting operation. Check the appliance is gas sound after completion.



DO NOT use reconditioned or unauthorised gas controls.



Disconnect from the electricity supply before servicing.



Before electrical reconnection, check that the appliance is electrically safe.

Injectors

Remove the burner caps and heads. Remove the old jets (Fig. 9.1). Fit the new jets (see ‘Technical Data’ section at the back of the book for correct jets). Reassemble in the reverse order.

Tap Adjustment

Removing the Control Panel

Pull o all the control knobs. Remove the three xing screws underneath the control panel (Fig. 9.2).

The control panel will drop down slightly. It is held at the top by two holes in the top edge, one at each end, that locate on the tags on the inner panel. Lift the control panel clear of the tags and pull forwards, taking care not to damage or strain the wiring.

Bypass Screw Adjustment

Turn the bypass screw on each control clockwise to the stop (Fig. 9.3).

Stick on Label

Stick the LP gas label over the natural gas part of the appliance data label.

ArtNo.0102-0011 - Screwing

the control valve bypass screw

9. Conversion to LP Gas

Fig. 9.1

Fig. 9.2

Fig. 9.3

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.

Pressure Testing

Connect the appliance to the gas supply.

Connect the appliance to the gas supply. Check the appliance is gas sound.

The gas pressure can be measured at one of the left hand hotplate burner jets. Lift o a burner head. Fit the pressure gauge to the jet. Turn on and light one of the other burners with a match. Turn on and press in the control knob for the burner with the pressure gauge tted.

The pressure should be 29 mbar for Butane and 37 mbar for Propane. After checking the pressure, turn o the taps and replace the burner head.

Reassemble burner top, making sure it is reassembled in the correct way on the burner body.

Check the appliance is gas sound.

Check operation of all the burners.

10. Circuit Diagram

P095199

g/y

A3A2A4

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Classic

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

Code Description

A1 Grill Front Switch

A2 Grill Energy Regulator

A3 Grill Elements -LH

A4 Grill Elements - RH

B1 Left-Hand Oven Thermostat

B2 Left Hand Oven Front Switch

B3 Left Hand Oven Fan Element

B4 Left Hand Oven Fan

C Clock / Timer

Code Description

D1 Right - Hand Oven Thermostat

D2 Right - Hand Oven Front Switch

D3 Right- Hand Oven Element

D4 Right - Hand Oven Fan

F1 Left - Hand Oven Thermal Preset

F2 Right - Hand Oven Thermal Preset

G Left Hand Oven Light

H Cooling Fan

I Indicator Neon

J Ignition Switch

K Oven Light Switch

L Spark Generator

P095199

v bk

b b b b b

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

Code Description

A1 Grill control

A2 Grill element right-hand side

A3 Grill element left-hand side

B1 Left-hand fan oven thermostat

B2 Left-hand fan oven control

B3 Left-hand fan oven element

B4 Left-hand fan oven fan

C Clock

D1 Right-hand fan oven thermostat

D2 Right-hand fan oven control

D3 Right-hand fan oven element

D4 Right-hand fan oven fan

Code Description

F1 Oven light switch

F2 Oven lamp

G1 Ignition switch

G2 Ignition spark generator

H Neon

I Thermal cut-out

J Cooling fan

Professional+ & Kitchener

P095199

g/y

A3A2A4

P095199

g/y

A3A2A4

HI-LITE Fan Oven

Key

The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.

Code Colour

b Blue

br Brown

bk Black

or Orange

r Red

v Violet

w White

y Yellow

g/y Green/yellow

gr Grey

Code Description

A Illumination board - left-hand side

A1 Grill front switch

A2 Grill energy regulator

A3 Left-hand grill element

A4 Right-hand grill element

B Illumination board - right-hand side

B1 Left-hand oven thermostat

B2 Left-hand front switch

B3 Left-hand oven element

B4 Left-hand oven fan

F1 Left-hand oven thermal preset

C Clock

Code Description

D1 Right-hand oven thermostat

D2 Right-hand oven front switch

D3 Right-hand oven element

D4 Right-hand oven fan

F2 Right-hand oven thermal preset

G Oven light

H Cooling fan

J Illumination switch

K Oven light switch

M1 Grill heat indicator

M2 Left-hand oven heat indicator

M3 Right-hand oven heat indicator

11. Technical Data

Classic

THE COOKER IS CATEGORY: CatII

2H3+.

It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.

COUNTRY OF DESTINATION: GB, IE.

Connections

Gas (Rp ½ at rear right-hand side) Electric

Natural Gas

20 mbar

230/400 V 50 H zButane 29 mbar

Propane 37 mbar

See the appliance badge for test pressures.

Dimensions

Model Classic 100 Dual Fuel

Overall height minimum 905 mm

maximum 930 mm

Overall width 994 mm

Overall depth

605 mm excluding handles, 667 mm including handles

Minimum height above the hotplate 650 mm

Hotplate Ratings

Hotplate

Bypass Screw*

Natural Gas 20mb L.P. Gas

Injector Injector

Wok burner 57

3.5 kW

internal 78

3.5 kW (246 g/h

internal 53

external 126 external 82

Rapide/ Large Burner 40 3 kW 134 3.0 kW (210 g/h) 87

Semi Rapide / Medium Burner 32

1.7 kW 109 1.7 kW (119 g/h) 68

Auxiliary / Small Burner 28

1 kW 75 1.0 kW (70 g/h) 51

* The valves in this cooker are ﬁtted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the bypass

screws must be screwed all the way down.

Hotplate energy saving tips Oven energy saving tips

Use cookware with a at base. Cook meals together, if possible. Use the correct size cookware. Keep the pre-heating time short. Use cookware with a lid. Do not lengthen cooking time. Minimise the amount of liquid or fat. Do not open the oven door during the cooking period. When liquid starts boiling, reduce the setting. Do not forget to turn the appliance o at the end of cooking. Consumption is based on G30.

Professional+

THE COOKER IS CATEGORY: CatII

2H3+.

It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.

COUNTRY OF DESTINATION: GB, IE.

Connections

Gas (Rp ½ at rear right-hand side) Electric

Natural Gas

20 mbar

230/400 V 50 H zButane 29 mbar

Propane 37 mbar

See the appliance badge for test pressures.

Dimensions

Model Professional+ 100 Dual Fuel

Overall height minimum 905 mm

maximum 930 mm

Overall width 994 mm

Overall depth

604 mm excluding handles, 645 mm including handles

Minimum height above the hotplate 650 mm

Hotplate Ratings

Hotplate

Bypass Screw*

Natural Gas 20mb L.P. Gas

Injector Injector

Wok burner 57

3.5 kW

internal 78

3.5 kW (246 g/h

internal 53

external 126 external 82

Rapide/ Large Burner 40 3 kW 134 3.0 kW (210 g/h) 87

Semi Rapide / Medium Burner 32

1.7 kW 109 1.7 kW (119 g/h) 68

Auxiliary / Small Burner 28

1 kW 75 1.0 kW (70 g/h) 51

* The valves in this cooker are ﬁtted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the bypass

screws must be screwed all the way down.

Hotplate energy saving tips Oven energy saving tips

Kitchener

THE COOKER IS CATEGORY: CatII

2H3+.

It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.

COUNTRY OF DESTINATION: GB, IE.

Connections

Gas (Rp ½ at rear right-hand side) Electric

Natural Gas

20 mbar

230/400 V 50 H zButane 29 mbar

Propane 37 mbar

See the appliance badge for test pressures.

Dimensions

Model Kitchener 100 Dual Fuel

Overall height minimum 905 mm

maximum 930 mm

Overall width 994 mm

Overall depth

605 mm excluding handles, 653 mm including handles

Minimum height above the hotplate 650 mm

Hotplate Ratings

Hotplate

Bypass Screw*

Natural Gas 20mb L.P. Gas

Injector Injector

Wok burner 57

3.5 kW

internal 78

3.5 kW (246 g/h

internal 53

external 126 external 82

Rapide/ Large Burner 40 3 kW 134 3.0 kW (210 g/h) 87

Semi Rapide / Medium Burner 32

1.7 kW 109 1.7 kW (119 g/h) 68

Auxiliary / Small Burner 28

1 kW 75 1.0 kW (70 g/h) 51

* The valves in this cooker are ﬁtted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the bypass

screws must be screwed all the way down.

Hotplate energy saving tips Oven energy saving tips

Hi-LITE

THE COOKER IS CATEGORY: CatII

2H3+.

It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.

INSTALLER: Please leave these instructions with the user.

DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.

COUNTRY OF DESTINATION: GB, IE.

Connections

Gas (Rp ½ at rear right-hand side) Electric

Natural Gas

20 mbar

230/400 V 50 H zButane 29 mbar

Propane 37 mbar

See the appliance badge for test pressures.

Dimensions

Model Hi-LITE 100 Dual Fuel

Overall height minimum 905 mm

maximum 930 mm

Overall width 994 mm

Overall depth

604 mm excluding handles, 650 mm including handles

Minimum height above the hotplate 650 mm

Hotplate Ratings

Hotplate

Bypass Screw*

Natural Gas 20mb L.P. Gas

Injector Injector

Wok burner 57

3.5 kW

internal 78

3.5 kW (246 g/h

internal 53

external 126 external 82

Rapide/ Large Burner 40 3 kW 134 3.0 kW (210 g/h) 87

Semi Rapide / Medium Burner 32

1.7 kW 109 1.7 kW (119 g/h) 68

Auxiliary / Small Burner 28

1 kW 75 1.0 kW (70 g/h) 51

* The valves in this cooker are ﬁtted with adjustable bypass screws. The cooker is supplied with the bypass screws set for Natural Gas. For LPG conversion the bypass

screws must be screwed all the way down.

Hotplate energy saving tips Oven energy saving tips

Hotplate Efficiency

Brand Rangemaster

Model Identication

Classic

Professional+

Kitchener

HI-LITE Size 100 Type Dual Fuel

Type of Hob GAS Number of gas burners 5 Auxiliary / Small Burner (EE gas burner) Semi Rapide / Medium Burner (EE gas burner) 58% Semi Rapide / Medium Burner (EE gas burner) 58% Rapide / Large Burner (EE gas burner) 56% Rapide / Large Burner (EE gas burner) Wok (EE gas burner) 53% Wok (EE gas burner) Hotplate EE gas hob (*) 56%

Information marked thus (*) is not required with mixed fuel hobs

Oven Data

Brand Rangemaster

Model identication

Classic

Professional+

Kitchener Mass kg 118 Model identication HI-LITE

kg 110 Type of oven Electric Number of cavities 2

Left-hand Eciency

Fuel type Electric Cavity type Fanned Power - conventional Power - forced air convection 2.5 Volume Litres 67 Energy consumption (electricity) - conventional kWh / cycle Energy consumption (electricity) - forced air convection kWh / cycle 0.8 Energy eciency index - conventional Energy eciency index - forced air convection 96.2 Energy class A

Right-hand Eciency

Fuel type Electric Cavity type Fanned (100) Power - conventional Power - forced air convection 2.5 Volume Litres 82 Energy consumption (electricity) - conventional kWh / cycle Energy consumption (electricity) - forced air convection kWh / cycle 0.79 Energy eciency index - conventional Energy eciency index - forced air convection 88.3 Energy class A

Additional Information

The oven complies with EN 60350-1 Maximum output @ 230V 50Hz Conventional 2.2 kW Multifunction Multifunction

(with Rapid Response) -

Forced Air Convection 2.5 kW Grill 2.3 kW Slow Oven Bread Proving Drawer -

Maximum total electrical load at 230 V (approximate total including hob, oven lights, oven fan, etc.): 7.4 kW

CONSUMER SERVICE

If you have any product enquiries, or in the event of a problem with your appliance once it has been installed, please telephone 0800 804 6261 or 0370 789 5107 from a mobile.

CONSUMER SERVICE LINES OPEN:

Monday to Thursday 8am–6pm Friday 8am–5pm Saturday 9am–1pm

WARRANTY

Your manufacturer warranty covers goods of our own brand for defective workmanship and materials for a period of 1 year from the date of purchase. This warranty covers mechanical breakdown and proven cosmetic and manufacturing defects.

You will receive an additional FREE full 12 months guarantee by registering your purchase using the FREEPOST form provided. Alternatively, call free on 0800 587 5747, quoting reference RMGX57A, or register online at www.rangemaster.co.uk.

Any damage, blemishes or chips identied upon receipt of the

product must be reported within 90 days – proof of purchase may be required to establish validity. Scratches on the surface of ceramic hobs must be reported within 14 days. Scratches caused by usage are not covered. Accidental damage is not covered by the manufacturer’s warranty.

For warranty compliance, the requirements are that the appliance:

• Has been correctly installed in accordance with current legislation, relevant British and European Standards and Codes of Practice, by a suitably competent person registered with Gas Safe or equivalent body and, where applicable, a

qualied electrician.

• Has been used solely for domestic cooking purposes.

• If in use in the UK*, has not been taken abroad as a personal export. (In the Republic of Ireland conditions may vary, so consult your retailer.)

• Is not second-hand or a refurbished appliance. The manufacturer’s warranty is not transferable.

• Has not been subject to misuse, accidental damage or

modication, and has not deteriorated due to normal

domestic wear and tear, and the manufacturer’s recommendations concerning cleaning materials have been followed.

• Has not been repaired by persons or organisations other than those authorised to act on behalf of AGA Rangemaster.

Exceptions:

• Items not included under the free 1 year guarantee include pan supports, griddles, wok rings, baking trays, grill pans,

trivets, lters, light bulbs and other consumable accessories.

• Any damage caused other than through normal use.

• Breakdowns associated with cooking spillage.

• Cosmetic deterioration deemed to be normal wear and tear.

This warranty is in addition to your Statutory Rights.

* Only certain models can be adapted for use with Mains Gas

supplied in the Channel Islands and Isle of Man.

OUT OF WARRANTY

We recommend that Rangemaster appliances are serviced regularly throughout their life to maintain optimum performance and

efciency. Service work should only be carried out by technically competent and suitably qualied personnel.

For your own safety, always make sure that work is carried out by a Gas Safe registered engineer for gas appliances or an approved electrician for electrical models.

For a competetive quote and to arrange for a Rangemaster approved engineer to attend, call Consumer Services on: 0800 804 6261 or 0370 789 5107 from a mobile.

SPARE PARTS

To maintain optimum and safe performance, we recommend that only genuine Rangemaster spare parts are used. These are available from most major spares stockists, including ourselves.

Contact Consumer Services on 0800 804 6261 or 0370 789 5107 from a mobile, who will be happy to help.

STANDARDS

Rangemaster cookers are designed and manufactured to a recognised international quality standard, which meets the requirements of BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001 for continually improving environmental procedures.

Rangemaster cookers comply with the essential requirements of the appropriate European Directives, and carry the CE mark.

Name of Appliance & Colour*

Appliance Serial Number*

Fuel Type*

Natural Gas LP Gas

Dual Fuel Electric

Retailer’s Name & Address

Date of Purchase

Installer’s Name & Address

Installer’s Telephone Number

Date of Installation

* This information is on the appliance data badge - look in the appliance instructions

to nd out where the data badge is located.

Built from experience

Rangemaster continuously seeks improvements in specication, design and production of products and thus, alterations

take place periodically. Whilst every effort is made to produce up-to-date literature, this brochure should not be regarded as

an infallible guide to current specication, nor does it constitute an offer for the sale of any particular appliance.

Clarence Street Royal Leamington Spa Warwickshire CV31 2AD England

Consumer Services: +44 (0)800 804 6261 or (0)370 789 5107 from a mobile. Fax: +44 (0)1926 450526 E-mail: consumers@agarangemaster.co.uk

www.rangemaster.co.uk

For UK Trade Enquiries Tel: +44 (0)115 946 4000 Fax: +44 (0)115 973 6602 E-mail: sales@agarangemaster.co.uk

For ROI Enquiries Tel: 1850 302 502

Rangemaster is a trading name of AGA Rangemaster Limited Registered in England and Wales. Registration No. 354715

Registered Ofce: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG

08706484000275

The Co-ordinating Collection.

Designed to impress

•Refrigeration • Sinks & Taps • Hoods & Splashbacks • Built-in Cooking • Dishwashing

Rangemaster Professional + 100, Kitchener 100, Classic 100, Hi-LITE 100 User's Manual & Installation Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual