Rangemaster CLassic / Professional +Kitchener / Hi-LITE, 100 Dual Fuel, Classic / Professional +, Kitchener / Hi-LITE User's Manual & Installation Instructions
Classic / Professional +
Kitchener / Hi-LITE
100 Dual Fuel
Britain’s No.1 Range Cooker
USER GUIDE &
INSTALLATION INSTRUCTIONS
RANGEMASTER COOKWARE
Our range cookers are well known for providing the
best possible cooking performance and years of
faithful service. However, a great cooker alone cannot
guarantee perfect results every time. The other vital
ingredients are of course enthusiasm and quality
cookware.
We oer cookware to work perfectly with all fuel types
manufactured by Rangemaster, including induction
hobs. You can be assured of functionality with style, as
well as the quality and meticulous attention to detail
you expect from the pioneers of range cooking.
Visit: www.rangemastercookshop.co.uk
Ingredients
• Oil for greasing
• 100 g strawberries
• 100 g raspberries
• 100 g redcurrants
• 100 g blackberries
• or a 400 g mixture of any soft
fruits
• 2 medium eggs
• 30 g caster sugar
• 80 ml skimmed milk
• 2 tsp vanilla extract
• 60 g plain our (sifted)
• 1 tsp baking powder
• Icing sugar to dust
Method
1. Preheat the oven to 200 °C (for a conventional oven),
180 oC (for a fan oven) or gas mark 6.
2. Lightly grease a dish 26 cm wide x 4 cm deep.
3. Thickly slice any large strawberries and place them with the other fruits
into an ovenproof dish, deep enough so the berries are about 2 deep.
4. Whisk the eggs and caster sugar until pale and uy. Beat the milk and
vanilla extract into the mixture and then fold in the sifted our and
baking powder.
5. Pour the cake mix over the fruit and bake on the centre shelf of the
oven for 15-20 minutes, or until the mixture is cooked through and
golden on the top.
6. Dust with icing sugar and serve immediately with cream or crème
fraiche.
FRUITY BAKED PUDDING
Serves 4–6
Ingredients
• 3 kg (6½ lb) skinned and
boned loin of pork
• 2 x 70 g packs prosciutto
• Grated zest of 2 lemons
• Bay leaves
• Salt and freshly ground
black pepper
For the sauce:
• 1 tablespoons plain our
• 4 tablespoons lemon
juice
• Chicken stock/water
Method
1. Preheat the oven to 220 °C (for a conventional oven), 200 °C (for a fan
oven) or gas mark 7.
2. Spread one of the packs of prosciutto over a chopping board; place
the pork on top with the outer (fat) part of the pork resting on the
prosciutto.
3. Sprinkle the lemon zest onto the inside of the meat and season well. Lay
the remaining prosciutto on top of the zest and roll up.
4. Secure the pork with string or silicone bands and thread bay leaves
under the string, covering the whole piece of pork. Put the meat on to
a trivet over a large roasting tin containing enough water to cover the
base.
5. Place into the oven and cook for 30 minutes. Reduce the heat to 180 °C
conventional oven/160 °C fan oven/gas 4 and continue roasting for a
further 25 minutes per 500 g. Should the prosciutto start becoming too
brown, cover with some foil.
6. When the pork is cooked, place onto a warm plate, cover with foil and
allow to rest for at least 20 minutes.
7. Spoon o most of the fat from the roasting tin and stir the our into the
remaining. Gradually add the stock and lemon juice, adding more stock
until the desired consistency is reached and simmer for 5 minutes. Check
the seasoning, adding more pepper or lemon juice as necessary.
8. Remove the string or bands from the pork and carve into slices, serve
with the sauce.
ROAST LOIN OF PORK WITH PROSCIUTTO
& BAY LEAVES
i
Contents
Classic, Kitchener, Professional+ & Hi-LITE 100 Dual Fuel
U110077-07A
1. Before You Start... 1
Important! 1
Installation and Maintenance 1
Peculiar smells 1
If you smell gas 1
Ventilation 1
Personal Safety 1
Cooker Care 2
Cleaning 2
2. Cooker Overview 3
Hotplate Burners 3
Wok Burner 4
The Wok Cradle (optional) 5
The Griddle (optional on Kitchener) 5
Main Oven Light 5
Fascia Illumination
(Hi-LITE only) 5
The Grill / Glide-out Grill (optional) 6
The Ovens 6
The Clock 7
Accessories 12
3. Cooking Tips 13
Tips on Cooking with the Timer 13
General Oven Tips 13
4. Cooking Table 14
5. Cleaning Your Cooker 15
Essential Information 15
Hotplate Burners 15
The Wok Cradle 15
The Griddle 15
Grills 16
Control Panel and Doors 16
Ovens 17
Ret in the reverse order. 17
The Tall Oven 17
Cleaning Table 18
6. Troubleshooting 19
7. Installation 21
Dear Installer 21
Safety Requirements and Regulations 21
Provision of Ventilation 21
Location of Cooker 22
Conversion 22
Positioning the Cooker 23
Moving the Cooker 23
Completing the Move 24
Fitting the Stability Bracket or Chain 24
Repositioning the Cooker Following
Connection 24
Conversion to Another Gas 25
Levelling 25
Gas Connection 25
Electrical Connection 26
Final Checks 27
Fitting the Plinth 27
Customer Care 27
8. Conversion to LP Gas 28
Injectors 28
Tap Adjustment 28
Stick on Label 28
Pressure Testing 29
9. Circuit Diagram 30
Circuit Diagram:
Classic 30
Circuit Diagram:
Professional+ & Kitchener 31
Circuit Diagram:
Hi-Lite Fan Oven 32
10. Technical Data 33
ii
1
Your cooker should give you many years of trouble-free
cooking if installed and operated correctly. It is important
that you read this section before you start, particularly if you
have not used a dual fuel cooker before.
Important!
This appliance is designed for domestic cooking
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen –
besides invalidating claims this wastes fuel and may
overheat the control knobs.
This appliance is for use in Great Britain and the
Republic of Ireland. It is a Cat II2H3+ cooker and is
set for G20 at 20mbar. (A conversion kit for LPG is
supplied with the cooker).
Installation and Maintenance
In the UK, the cooker must be installed by a Gas Safe
registered engineer. The electrical installation should be in
accordance with BS7671. Otherwise, all installations must be
in accordance with the relevant instructions in this booklet,
with the relevant national and local regulations, and with the
local gas and electricity supply companies’ requirements.
Ensure that the gas supply is turned on and that the cooker is
wired in and switched on (the cooker needs electricity).
Set the clock to ensure that the oven is functional – see the
relevant section in this manual.
Only a qualied service engineer should service the cooker,
and only approved spare parts should be used.
Always allow the cooker to cool and then switch it o at the
mains before cleaning or carrying out any maintenance work,
unless specied otherwise in this guide.
Peculiar smells
When you rst use your cooker it may give o a slight odour.
This should stop after a little use.
Before using for the rst time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200°C and run for an
hour.
Before using the grill for the rst time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
If you smell gas
• DO NOT turn electric switches on or off.
• DO NOT smoke
• DO NOT use naked flames
• DO turn off the gas at the meter or cylinder
• DO open doors and windows to get rid of the gas
• DO keep people away from the area affected
• Call your gas supplier.
If you are using natural gas in the UK, ring the National Grid
on: 0800 111 999.
Ventilation
The use of a gas cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, ensure that the kitchen is well ventilated: keep
natural ventilation holes open or install a powered cooker
hood that vents outside. If you have several burners on, or
use the cooker for a long time, open a window or turn on an
extractor fan.
Personal Safety
Do not modify this appliance.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in
a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
This appliance is not intended for use by young
children or inrm persons unless they have been
adequately supervised by a responsible person to
make sure that they can use the appliance safely.
CAUTION: A long term cooking process has to be
supervised from time to time. A short term cooking
process has to be supervised continuously.
Danger of re: DO NOT store items on the cooking
surfaces.
To avoid overheating, DO NOT install the cooker
behind a decorative door.
WARNING: The appliance and its accessible parts
become hot during use and will retain heat even
after you have stopped cooking. Care should be
taken to avoid touching heating elements. Children
less than 8 years of age shall be kept away unless
continuously supervised.
DO NOT use a steam cleaner on your cooker.
1. Before You Start...
2
Accessible parts will become hot during use and will
retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and
never wear loose-tting or hanging clothes when
using the appliance.
Always be certain that the controls are in the OFF position
when the oven is not in use, and before attempting to clean
the cooker.
When the oven is on, DO NOT leave the oven door
open for longer than necessary, otherwise the
control knobs may become very hot.
When using the grill, make sure that the grill pan
is in position and pushed fully in, otherwise the
control knobs may become very hot.
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Always keep combustible materials, e.g. curtains, and
ammable liquids a safe distance away from your cooker.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Use dry oven gloves when applicable – using damp gloves
might result in steam burns when you touch a hot surface.
Do not use a towel or other bulky cloth in place of a glove – it
might catch re if brought into contact with a hot surface.
NEVER operate the cooker with wet hands.
DO NOT use aluminium foil to cover shelves, linings
or the oven roof.
DO NOT use hotplate protectors, foil or hotplate
covers of any description. These may aect the safe
use of your hotplate burners and are potentially
hazardous to health.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always ensure that
you position the handles away from the edge of the
hotplate.
DO NOT use cooking vessels on the hotplate that
overlap the edges.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on re. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
WARNING!
Unattended cooking on a hob with fat or oil can be
dangerous and may result in re.
NEVER leave a chip pan unattended. Always heat fat
slowly, and watch as it heats. Deep fry pans should
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
DO NOT use the top of the ue (the slot along the
back of the cooker) for warming plates, dishes,
drying tea towels or softening butter.
DO NOT use water on grease res and never pick
up a aming pan. Turn the controls o and then
smother a aming pan on a surface unit by covering
the pan completely with a well tting lid or baking
tray. If available, use a multipurpose dry chemical or
foam-type re extinguisher.
Cooking high moisture content foods can create a ‘steam
burst’ when the oven door is opened (Fig. 1.1). When
opening the oven stand well back and allow any steam to
disperse.
Take care that no water seeps into the appliance.
This appliance is heavy so take care when moving it.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
Cleaning
In the interests of hygiene and safety, the cooker should be
kept clean at all times as a build up in fats and other food
stu could result in a re.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid steam burns. Some
cleansers can produce noxious fumes if applied to a hot
surface.
ArtNo.324-0001 Steam burst
Fig. 1.1
3
ArtNo.270-0001
Proplus control to high
The 100 dual fuel cooker (Fig. 2.1) has the following features:
A. 5 hotplate burners including a wok burner
B. Control panel incorporting a timer
C. Separate grill or glide-out grill (depending on model)
D. Main fan oven
E. Tall fan oven
Hotplate Burners
The drawing by each of the central knobs indicates which
burner that knob controls.
Each burner has a Flame Supervision Device (FSD) that
prevents the ow of gas if the ame goes out.
When the igniter button is pressed in, sparks will be
made at every burner – this is normal. Do not attempt to
disassemble or clean around any burner while another
burner is on, otherwise an electric shock could result.
To light a burner, press the igniter button, and push in and
turn the associated control knob to the high position as
indicated by the large ame symbol (
), (Fig. 2.2).
The igniter should spark and light the gas. Keep holding the
knob pressed in to let the gas through to the burner for about
ten seconds.
Professional +
A
B
D
C
E
2. Cooker Overview
Fig. 2.1
Fig. 2.2
DocNo.020-0006 - Overview - 100DF - Prof+
4
ArtNo.311-0002 Pan with rim
If, when you let go of the control knob, the burner goes out,
then the FSD has not been bypassed. Turn the control knob
to the OFF position and wait for one minute before you try
again, this time making sure to hold in the control knob for
slightly longer.
Adjust the ame height to suit by turning the knob counterclockwise (Fig. 2.3). On this cooker the low position is
beyond high, NOT between high and o.
If a burner ame goes out, turn o the control knob and
leave it for one minute before relighting it.
Make sure that the ames are under the pans. Using a lid will
help the contents boil more quickly (Fig. 2.4).
Large pans should be spaced well apart.
Pans and kettles with concave bases or down-turned base
rims should not be used (Fig. 2.5).
Simmering aids, such as asbestos or mesh mats, are
NOT recommended (Fig. 2.6). They will reduce burner
performance and could damage the pan supports.
You should also avoid using unstable and misshapen pans
that may tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers (Fig. 2.7).
The minimum recommended pan diameter is 120 mm. The
maximum allowable pan base diameter is 260 mm.
DO NOT use cooking vessels on the hotplate that overlap the
edges.
Wok Burner
The wok burner is designed to provide even heat over a large
area. It is ideal for large pans and stir-frying (Fig. 2.8).
For heating smaller pans, the aforementioned hotplate
burners may be more ecient.
You should wipe the enamel top surface of the cooker around
the hotplate burners as soon as possible after spills occur. Try
to wipe them o while the enamel is still warm.
Note:
The use of aluminium pans may cause metallic marking
of the pan supports. This does not aect the durability of the
enamel and may be cleaned o with an appropriate metal
cleaner.
ArtNo.311-0001 Right pans gas
ArtNo.270-0003
Proplus control to low
Art No. 311-0003 Simmer aids
ArtNo.311-0004 T ipping wok
ArtNo.311-0005 Wok burner & pan support
Fig. 2.3
Fig. 2.4
Fig. 2.5
Fig. 2.6
Fig. 2.7
Fig. 2.8
5
ArtNo.090-0002 90 Griddle position
ArtNo.090-0004 Incorrect griddle position
ArtNo.311-0006 Correct wok sizes
The Wok Cradle (optional)
The wok cradle is designed to t a 35 cm wok. If you use a
dierent wok, make sure that it ts the cradle. Woks vary very
widely in size and shape. It is important that the wok sits
down on the pan support – however, if the wok is too small,
the cradle will not support it properly (Fig. 2.9).
The cradle should be used on the wok burner only. When you
t the cradle, make sure that it is supported properly on a pan
support and the wok is sitting level in the cradle (Fig. 2.10).
The cradle will get very hot in use – allow plenty of time for it
to cool before you pick it up.
The Griddle (optional on Kitchener)
The griddle ts the left-hand pan support, front to back (Fig.
2.11). It is designed for cooking food on directly. DO NOT use
pans of any kind on it. The griddle surface is non-stick and
metal cooking utensils (e.g. spatulas) will damage the surface.
Use heat resistant plastic or wooden utensils.
DO NOT put it crossways – it will not t properly and
will be unstable (Fig. 2.12).
DO NOT put it on any other burner – it is not
designed to t in any of the other pan supports.
Position the griddle over the hotplate burners resting on the
pan support. Check that it is securely located.
The griddle can be lightly brushed with cooking oil before
use (Fig. 2.13). Light the hotplate burners. Adjust the ame
heights to suit.
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. Turn the
control knobs towards the low position, marked with the
small ame symbol, to reduce the burner ames.
Always leave space around the griddle for the gases
to escape.
NEVER t two griddles side by side (Fig. 2.14).
After cooking, allow the griddle to cool before cleaning.
Main Oven Light
Press the button to turn the light on (Fig. 2.15). If the oven
light fails, turn o the power supply before changing the
bulb. See the ‘Troubleshooting’ section for details on how to
change the bulb.
Fascia Illumination
(Hi-LITE only)
To turn on the fascia illumination panel simply push the
button in (Fig. 2.16). To turn this feature o, push the button
once more.
ArtNo.311-0007 Wok stand close-up
ArtNo.311-0009 Oil on griddle
ArtNo.320-0017
Main oven light
ArtNo.311-0008 Griddle positioning
ArtNo.320-0017
Main oven light
Fig. 2.9
Fig. 2.10
Fig. 2.11
Fig. 2.12
Fig. 2.13 Fig. 2.14
Fig. 2.15 Fig. 2.16
6
The Grill / Glide-out Grill (optional)
Open the door and, using the handle, pull the grill pan
(Fig. 2.17) or carriage (Fig. 2.18) forward.
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Adjust the heat to suit by turning the knob. To heat the whole
grill, turn the knob clockwise (Fig. 2.19).
To heat the right-hand half, turn the knob counter-clockwise.
The neon indicator light by the grill control will come on.
For best results, leave the grill pan in the grill chamber and
preheat the appropriate part(s) of the grill for two minutes.
The grill trivet can be removed and the food placed on it
while you are waiting for the grill to preheat.
DO NOT leave the grill on for more than a few
moments, without the grill pan underneath it,
otherwise the knobs may become hot.
Once the grill has preheated, take the grill pan out again and
put the trivet back in place with the food on it. Slide the grill
pan or carriage back into the grill chamber. Make sure that it
is pushed right in.
Accessible parts may be hot when the grill is in use.
Young children should be kept away.
The grill pan trivet can be turned over to give two grilling
positions (Fig. 2.20).
Never close the grill door when the grill is on.
The Ovens
The clock must be set to the time of day before the ovens
will work. See the following section on ‘The Clock’ for
instructions on setting the time of day.
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
Both ovens are fan ovens that circulate hot air continuously,
which means faster, more even cooking.
The recommended cooking temperatures for a fan oven are
generally lower than a conventional oven.
Note: Please remember that all cookers vary so temperatures
in your new ovens may dier to those in your previous
cooker.
Operating the Ovens
1. Turn the oven knob to the desired temperature (Fig.
2.21).
2. The oven indicator light will glow until the oven has
reached the temperature selected (Fig. 2.22). It will then
cycle on and o during cooking.
ArtNo.331-0002 Grill pan high/low position
ArtNo.331-0001Grill pan pulled forwards
ArtNo.270-0004
Proplus grill control
1
1
2
2
3
3
0
ArtNo.270-0005 Proplus
electric oven control
140
100
180
220
0
ArtNo.270-0006 Proplus
oven control light
140
100
180
220
0
ArtNo.330-0003 - Grill pan w handle pulled forwards
Fig. 2.17
Fig. 2.18
Fig. 2.19
Fig. 2.20
Fig. 2.21 Fig. 2.22
7
The Clock
You can use the clock to turn the left-hand oven on and o.
The clock must be set to the time of day before the oven
will work.
Setting the 2-button Clock (Professional+ & Hi-LITE)
The 2-button LCD clock can only display a 24 hour clock. The
Multifunction Oven on the left will not operate unless the
clock has been set.
1. Once the cooker is connected and switched on, the
display will start to ash.
2. To set the time, turn and hold the Timer (A) knob to
the Clock (C) setting and at the same time turn the
Adjusting (B) knob either left or right (Fig. 2.23).
3. Once you have set the time release the Timer (A) knob.
Setting the Minute Minder
A Minute Minder (E) is a feature that can be set for a number
of minutes and sounds an alarm once the specied amount
of time has elapsed.
1. Turn the Timer (A) knob to the Minute Minder (E)
setting – it should click into position (Fig. 2.24)
2. Turn the Adjusting (B) knob to set the amount of time
required. e.g. 20 seconds (Fig. 2.25).
3. Turn the Timer (A) knob to the Manual (D) setting to
see the current time and the ‘Bell’ symbol on the display
(Fig. 2.26).
4. Once the specied time has elapsed it will emit an alarm.
There are two ways to cancel the alarm:
I. Turn the Adjusting (B) knob counter-clockwise or
clockwise (Fig. 2.27).
II. Turn either the Timer (A) knob to the Clock (C) or to
the Minute Minder (E) setting. Return to Manual (D)
for normal cooking mode (Fig. 2.27).
A – Timer knob, B – Adjusting knob
Fig. 2.23
Fig. 2.24
Fig. 2.25
Fig. 2.26
Fig. 2.27
ArtNo.300-0005 2BC
minute minder setting
A B
C
ArtNo.300-0005 2BC
minute minder setting
E
A B
ArtNo.300-0006 2BC
minute minder setting 2
A B
ArtNo.300-0006 2BC
minute minder setting 2
D
E
C
A B
ArtNo.301-0007 2BC
Stopping the oven 1
D
A B
E
C
8
ArtNo.301-0008 2BC
Stopping the oven 2
G
A B
ArtNo.301-0008 2BC
Stopping the oven 2
H
A B
ArtNo.301-0007 2BC
Stopping the oven 1
D
A B
ArtNo.301-0007 2BC
Stopping the oven 1
D
A B
E
C
To Stop the Multifunction Oven at a Specific
Time of Day
You have set the required temperature and function mode for
the Multifunction Oven and you would like the Multifunction
Oven to automatically stop.
TOP TIP
Make a note of the current time so you do not forget.
1. Turn the Timer (A) knob to the Stop Time (G) setting
(Fig. 2.28).
2. Turn the Adjusting (B) knob clockwise, the display will
show the current time of day (Fig. 2.28).
3. Continue to turn the Adjusting (B) knob to the amount
of time required e.g. 1 minute. The display will show the
current time plus the required length of time you have
set (Fig. 2.29)
4. Turn the Timer (A) knob to the Auto (H) setting (Fig.
2.29). The display will show the current time, the Cooking
symbol and the word ‘AUTO’ (Fig. 2.29).
5. Once the specied time has elapsed it will emit an alarm
and the Multifunction Oven will stop working. The
‘Cooking’ symbol on the display will disappear and the
word ‘AU TO’ will ash (Fig. 2.30).
6. When you return, turn the Timer (A) knob to the Manual
(D) setting to return to manual cooking and reset the
Multifunction Oven modes once cooking is complete
(Fig. 2.30).
7. Once the specied time has elapsed it will emit an alarm.
There are two ways to cancel the alarm:
I. Turn the Adjusting (B) knob counter-clockwise or
clockwise (Fig. 2.31).
II. Turn either the Timer (A) knob to the Clock (C) or to
the Minute Minder (E) setting. Return to Manual (D)
for normal cooking mode (Fig. 2.31).
Fig. 2.28
Fig. 2.29
Fig. 2.30
Fig. 2.31
9
ArtNo.301-0007 2BC
Stopping the oven 1
A B
C
ArtNo.301-0008 2BC
Stopping the oven 2
G
A B
ArtNo.301-0008 2BC
Stopping the oven 2
H
A B
ArtNo.301-0007 2BC
Stopping the oven 1
D
A B
ArtNo.301-0007 2BC
Stopping the oven 1
D
A B
E
C
To Start and Stop the Multifunction Oven
The Multifunction Oven allows you to automatically start and
stop by a combination of the length of the cooking time and
the stop time. Giving you the exibilty to cook casseroles etc
while you are out. You cannot set the actual start time.
TOP TIP
Make a note of the current time so you do not forget.
1. Turn the Timer (A) knob to the Stop Time (G) setting
(Fig. 2.32).
2. Turn the Adjusting (B) knob clockwise, the display will
show the current time of day (Fig. 2.33).
3. Continue to turn the Adjusting (B) knob to the amount
of time required e.g. 1 minute. The display will show the
current time plus the required length of time you have
set (Fig. 2.33)
4. Turn the Timer (A) knob to the Auto (H) setting (Fig.
2.33). The display will show the current time, the Cooking
symbol and the word ‘AUTO’.
5. Once the specied time has elapsed it will emit an alarm
and the Multifunction Oven will stop working. The
‘Cooking’ symbol on the display will disappear and the
word ‘AU TO’ will ash (Fig. 2.34).
6. When you return, turn the Timer (A) knob to the Manual
(D) setting to return to manual cooking and reset the
Multifunction Oven modes once cooking is complete
(Fig. 2.35).
7. Once the specied time has elapsed it will emit an alarm.
There are two ways to cancel the alarm:
I. Turn the Adjusting (B) knob counter-clockwise or
clockwise (Fig. 2.35).
II. Turn either the Timer (A) knob to the Clock (C) or to
the Minute Minder (E) setting. Return to Manual (D)
for normal cooking mode (Fig. 2.35).
Reset to Manual Cooking
To cancel any automatic settings turn the Timer (A) knob to
the Clock (C) setting and release (Fig. 2.36).
Key Lock
The Key Lock will activate and deactivate the left-hand oven.
The right-hand tall oven can be operated as usual.
1. Cancel any active programs. Refer to ‘Reset to Manual
Cooking’.
2. Turn the Timer (A) knob to the Clock (C) setting and hold
for approx 8 seconds. The display will show ‘ON’ (Fig.
2.37).
3. Continue to hold the Timer (A) knob onto the Clock (C)
setting, turn the Adjusting (B) knob clockwise, the ‘OF‘
and the ‘Key’ symbol will display (Fig. 2.38). The lefthand oven is now locked.
Fig. 2.32
Fig. 2.33
Fig. 2.34
Fig. 2.35
Fig. 2.36
Fig. 2.37 Fig. 2.38
ArtNo.301-0012 2BC
Activating the key lock 2
A B
Art No. 301-0011 2BC
Activating the key lock 1
A B
• The ‘cook period’, which is the length of time you want
the oven to cook for.
• The ‘stop time’, which is the time of day you want the
oven to stop cooking.
10
4. To activate repeat steps 1 to 2 and continue to hold
the Timer (A) knob onto the Clock (C) setting, turn the
Adjusting (B) knob clockwise to ‘ON’, the ‘Key’ symbol
will disappear and the left-hand oven is enabled.
Setting the 6-button Clock (Classic & Kitchener)
1. The 6-button LCD clock is shown in Fig. 2.39. When the
clock is rst connected the display ashes ( 0.00 ) and
() alternately.
2. Press and hold both the [] and [] buttons down
(Fig. 2.40). Now press the [+] button (or the [–] button)
until the correct time shows.
3. Do not forget that it is a 24-hour clock.
4. If you need to reset the cooker, turn o the power supply
and wait for a couple of minutes and start again.
Setting the Minute Minder
1. Press and hold the [] button (Fig. 2.41), and then press
the [+] button until the length of time you want to cook
for is shown (Fig. 2.42).
2. You can check the time remaining by pressing []. When
the beeper sounds cancel it by pressing [].
• The ‘cook period’, which is the length of time you
want the oven to cook for.
• The ‘stop time’, which is the time of day you
want the oven to stop cooking.
To Stop the Oven Automatically
1. Press and hold the Stop Time [] button (Fig. 2.43) and
then press the [+] button (or [–] button) until the required
‘stop time’ shows (Fig. 2.44). AUTO will show in the
display.
2. Once the ‘stop time’ is reached, the beeper sounds. To
stop the beep turn the oven control knob to 0 rst and
then press [] once; press [] again to return to manual
cooking.
To Start and Stop the Oven Automatically
Before you set the clock you must have two numbers clearly
in mind – the ‘cook period’ and the ‘stop time’.
Note: You cannot set a start time directly – this is set
automatically by setting the ‘cook period’ and the ‘stop time’.
1. Press and hold the [] button (Fig. 2.45) and then press
the [+] button (or [–] button) until the required ‘cook
period’ shows (Fig. 2.46)
2. Now press and hold the [] button (Fig. 2.47) and then
press the [+] button (or [–] button) until the required ‘stop
time’ shows (Fig. 2.48). Release the buttons.
3. AUTO will now show in the display.
4. Set the oven to the required temperature. When cooking
is nished the beeper will sound. Turn the oven knob
to the OFF position rst, and then press the [] button
once to stop the beep; press it again to return to manual
cooking.
ArtNo.302-0001 - 6-button clock
ArtNo.302-0003 - 6BC
minute minder setting 1
ArtNo.302-0004 -
Minute minder setting 2
ArtNo.302-0005 -
6BC Stopping the oven 1
ArtNo.302-0002 - 6BC annotated
A B C D E F
A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time,
D – Manual, E & F – Time setting buttons
ArtNo.302-0005a -
6BC Stopping the oven 1a
ArtNo.302-0006 - 6BC
setting the cook time
ArtNo.302-0006 - 6BC
setting the cook time
ArtNo.302-0005 -
6BC Stopping the oven 1
ArtNo.302-0005a -
6BC Stopping the oven 1a
Fig. 2.39
Fig. 2.40
Fig. 2.41
Fig. 2.43
Fig. 2.45
Fig. 2.47
Fig. 2.42
Fig. 2.44
Fig. 2.46
Fig. 2.48
11
5. If you are out, do not worry about the beeper going o, it
stops after a while. When you return, turn the oven knob
to 0 rst, and then press [] twice to return to manual
cooking.
Reset to Manual Cooking
1. To return to manual cooking from any automatic setting,
the ‘cook period’ must be cancelled. Press and hold the
[] button and then press the [ –] button until the display
reads ( 0.00 ).
2. Press the [] button to return to manual cooking.
Key Lock
The Key Lock will activate and deactivate the left-hand oven.
The right-hand tall oven can be operated as usual.
To Turn On the Key Lock
1. Hold the Minute Minder [] and Cook period []
buttons. When ‘On’ appears on the display (Fig. 2.49)
press the [+] button once. The key symbol [] and ‘OF’ will
now show on the display (Fig. 2.50). Release the buttons.
2. The left-hand oven is now locked, as conrmed by
the display showing the time of day alongside the key
symbol (Fig. 2.51).
To Turn Off the Key Lock
1. Hold the Minute Minder [] and Cook period []
buttons. When ‘OF’ appears on the display (Fig. 2.52)
press the [+] button once. The key symbol [] will go out
and ‘On’ will show on the display (Fig. 2.53). Release the
buttons.
2. After a few seconds the display will revert to show the
time of day. The oven can now be used normally.
ArtNo.302-0010 Activating the key lock 3
ArtNo.302-0008 Activating the key lock 1
ArtNo.302-0009 - Activating
the key lock 2
ArtNo.302-0011 - 6BC
Deactivating the key lock 1
ArtNo.302-0012 Deactivating the key lock 2
Fig. 2.49 Fig. 2.50
Fig. 2.51
Fig. 2.52
Fig. 2.53
12
Accessories
Oven Shelves – Left-hand (Main) Oven
In addition to the at shelves, some models are supplied
with a drop shelf (Fig. 2.54). The drop shelf increases the
possibilities for oven shelf spacing.
The oven shelves can be easily removed and retted.
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig. 2.55).
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig. 2.56).
To ret the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig. 2.57).
Oven Shelves – Right-hand (Tall) Oven
The tall oven is supplied with four at cooking shelves
(Fig. 2.58), and a plate-warming shelf (Fig. 2.59).
Please note: The Hi-LITE does not have a plate warming shelf,
but is supplied with three at cooking shelves.
When using the tall oven, you can cook on all four shelves at
the same time, but make sure that they are well spaced out to
allow the hot air to circulate.
The Handyrack (Main Oven)
The Handyrack (Fig. 2.60) ts to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
The maximum weight that can be held by the Handyrack
is 5.5 kg (12 lb). It should only be used with the supplied
roasting tin, which is designed to t the Handyrack. Any other
vessel could be unstable.
It can be tted at two dierent heights. One of the oven
shelves must be removed and the other positioned to suit.
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
To t the Handyrack, locate one side of it on the door bracket
(Fig. 2.61). Then spring the other side out to clip it onto the
other bracket (Fig. 2.62).
ArtNo.324-0002 Oven shelf
ArtNo.320-0013 Removing the shelf 3
ArtNo.320-0015
Fitting the Handyack 1
ArtNo.320-0016
Fitting the handyrack 2
ArtNo.320-0011 Removing the shelf 1
ArtNo.320-0012 Removing the shelf 2
Shelf guard
Front
Front
Shelf guard
Flat shelf
Drop shelf
ArtNo.324-0010 Plate warming shelf
Fig. 2.54
Fig. 2.55
Fig. 2.57
Fig. 2.59
Fig. 2.61
Fig. 2.56
Fig. 2.58
Fig. 2.60
Fig. 2.62
13
Tips on Cooking with the Timer
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’ slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
Very perishable foods such as pork or sh should be avoided
if a long delay period is planned, especially in hot weather.
DO NOT place warm food in the oven to be timed.
DO NOT use a timed oven that is already warm.
DO NOT use the timed oven if the adjoining oven is
already warm.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
General Oven Tips
The wire shelves should always be pushed rmly to the back
of the oven.
Baking trays with food cooking on them should be placed
level with the front edge of the oven’s wire shelves. Other
containers should be placed centrally. Keep all trays and
containers away from the back of the oven, as overbrowning
of the food may occur.
For even browning, the maximum recommended size of a
baking tray is 340 mm (13½”) by 340 mm (13½”) in the main
oven and 232 mm (91/8”) by 321 mm (125/8”) in the tall oven.
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
• Always leave a “finger’s width” between dishes on
the same shelf. This allows the heat to circulate freely
around them.
• To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
• Where dishes may boil and spill over during cooking,
place them on a baking tray.
• The ‘Cook & Clean’ oven liners (see ‘Cleaning Your
Cooker’) work better when fat splashes are avoided.
Cover meat when cooking with foil or use a roasting
bag.
• Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
• If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
3. Cooking Tips
14
4. Cooking Table
ArtNo.050-0007
Oven shelf positions
Oven Shelf Positions
Top (T)
Centre (C)
Base (B)
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10 °C and the cooking time by 5-10 minutes. The
temperature in the fan oven does not vary with height in the oven so you can use any shelf.
Food
Meat
Beef (no bone)
Lamb
Pork
Poultry
Chicken
Turkey
Duck
Casserole
Yorkshire Pudding
Cake
Very rich fruit - Christmas,
wedding, etc.
Fruit 180 mm tin
Fruit 230 mm tin
Madeira 180 mm
Small cakes
Scones
Victoria sandwich
180 mm tin
210 mm tin
Desserts
Shortcrust tarts
Fruit pies
Tartlets
Puff pastry
Meringues
Baked egg custard
Baked sponge pudding
Milk pudding
Bread
Fish
Fillet
Whole
Steak
Approximate Cooking Time
30-35 minutes per 500g +30-35 minutes.
20-25 minutes per 500g +20-25 minutes.
30-35 minutes per 500g +30-35 minutes.
25-30 minutes per 500g +25-30 minutes.
35-40 minutes per 500g +35-40 minutes.
25-30 minutes per 500g +25-30 minutes.
20-25 minutes per 500g +20-25 minutes.
15-20 minutes per 500g +15-20 minutes.
20 minutes per 500g +20 minutes.
15 minutes per 500g +15 minutes.
25-30 minutes per 500g.
20 minutes per 500g.
2-4 hours according to recipe.
Large tins 30-35 minutes; individual 10-20 minutes.
45-50 minutes per 500g of mixture.
2-2½ hours.
Up to 3½ hours.
80-90 minutes.
15-25 minutes.
10-15 minutes.
20-30 minutes.
30-40 minutes.
20-30 minutes on a preheated tray.
35-45 minutes.
10-20 minutes according to size.
20-40 minutes according to size.
2-3 hours.
45-60 minutes.
40-45 minutes.
2 to 3 hours.
20-30 minutes.
15-20 minutes.
15-20 minutes per 500g.
Steaks according to thickness.
Conventional Oven
Temperature °C
(Shelf Position)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
160 (C)
200 (C)
140-150 (C)
220 (C)
140 (C/B)
150 (C/B)
150 (C/B)
160 (C/B)
170 (C/B)
200 (C/B)
170 (C/B)
170 (C/B)
200 (C/B)
180 (C/B)
180 (C/B)
210 (C/B)
100 (C/B)
160 (C/B)
180 (C/B)
140-150 (C/B)
210 (C)
Fanned Grilling
190 (C/B)
190 (C/B)
190 (C/B)
Fan Oven
Temperature
°C
150
190
150
190
150
190
150
190
150
190
150
190
130-140
210
130
140
140
150
160
190
160
160
190
170
170
200
90
150
170
130-140
200
190 (C/B)
190 (C/B)
190 (C/B)
Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
220°C (210°C for fan oven) and the
cooking time adjusted accordingly.
For stuffed and rolled meats, add
approximately 10 minutes per 500g,
or cook at 200°C (190°C) for 20
minutes then 160°C (150°C) for the
remainder.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Using the conventional oven: when
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
ArtNo.050-0001 Gas cooking table
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340 mm
x 340 mm. This ensures free heat
circulation.
If cooking a two tier load, the trays
should be interchanged
approximately halfway though the
cooking time.
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
T - Top; C - Centre; B - Base
DocNo.031-0004 - Cooking table - electric & fan single cavity
15
ArtNo.311-0032 Burner layout FSD
A
B
C
D
E
ArtNo.311-0033 Wok burner details FSD
A
B
C
D
E
ArtNo.311-0016 Fitting the burner inner head
A
B
A – Cap, B – Head, C – Notch, D – Base , E – Electrode
A – Inner burner cap, B – Outer burner cap, C – Inner burner head, D
– Outer burner head, E – Wok burner base
A – Electrode notch, B – Ignition electrode
Essential Information
Isolate the electricity supply before carrying out any
thorough cleaning. Allow the cooker to cool.
NEVER use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt.
DO NOT mix dierent cleaning products – they may
react together with hazardous results.
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
Remember to switch on the electricity supply and reset the
clock before re-using the cooker.
Hotplate Burners
The burner heads and caps can be removed for cleaning.
DO NOT put the burner heads in a dishwasher.
Make sure they are absolutely dry before replacing them.
The Single Ring Burners
When retting the burner head, make sure that the notch
lines up with the electrode or hole in the base. Check that the
burner head is level and that the cap is tted centrally on the
burner head (Fig. 5.1).
The Wok Burner
The Wok burner can also be taken apart for cleaning.
When reassembling the wok burner (Fig. 5.2), turn over the
large base ring and nd the ‘D’ shaped area (Fig. 5.3). Turn
the head until the ‘D’ matches the one on the burner base.
Flip the burner over once again and place it on the burner
base.
To t the small inner burner, nd the larger electrode notch in
the burner rim. Line this up with the white ignition electrode
and place the inner burner on the large base ring (Fig. 5.4).
Now t the two burner caps, making sure that they are seated
properly.
Check the burner ports are not blocked. If a blockage occurs,
remove stubborn particles using a piece of fuse wire.
The Wok Cradle
Recommended cleaning materials are hot soapy water, a
moistened soap pad, cream cleaner or a nylon scourer.
The Griddle
Always clean the griddle after use. Allow it to cool completely
before removing. Immerse the griddle plate in hot soapy
water. Use a soft cloth or, for stubborn stains, a nylon washing
up brush.
Note: If the griddle is washed in a dishwasher then some
dishwasher residue may appear on the back. This is normal
and will not aect the performance of your griddle.
5. Cleaning Your Cooker
Fig. 5.1
Fig. 5.2
Fig. 5.3
Fig. 5.4
16
ArtNo.331-0001Grill pan pulled forwards
ArtNo.331-0003 Grill frame out, no pan
ArtNo.331-0004 Removing the grill frame
ArtNo.331-0005 Removing the grill rail
ArtNo.331-0006 Grill pan plan
Grills
The grill pan and trivet should be washed in hot soapy water.
After grilling meats or any foods that soil, leave to soak for a
few minutes immediately after use. Stubborn particles may
be removed from the trivet using a nylon brush. Alternatively,
the grill pan can be washed in a dishwasher.
Before you remove any of the grill parts for cleaning,
make sure that they are cool, or use oven gloves.
DO NOT use any abrasive substances.
Cleaning the Glide-out Grill
The grill pan can be easily removed for cleaning as follows:
Remove the grill pan support frame by pulling the grill pan
forward (Fig. 5.5).
Lift the grill pan clear of the support frame.
The support frame
is held to the side rails by two clips on each side (Fig. 5.6).
For each side, support the side rail with one hand and with
the other hand lift the frame up and out of the side clips (Fig.
5.7).
For safety, push the side rails back into the grill chamber.
If you need to remove the side rails to allow cleaning of the
grill chamber, you can unhook them from the grill chamber
sides (Fig. 5.8) and wipe the sides clean with a soft cloth and
mild detergent.
DO NOT put the side runners in a dishwasher.
Once you have nished, hook the side rails back onto the
sides of the chamber. To ret the frame, pull the side rails
forward and, for each side in turn, support the side rail and
press the frame down into the side rails.
Ret the grill pan. When retting the grill pan, make sure that
the wide rim is at the front (Fig. 5.9).
Control Panel and Doors
Avoid using any abrasive cleaners including cream cleaners.
For best results, use a liquid detergent.
The same cleaner can be used on the doors, or alternatively,
using a soft cloth wrung out in clean hot soapy water – but
take care that no surplus water seeps into the appliance.
After cleaning, polish with a dry cloth.
Fig. 5.5
Fig. 5.6
Fig. 5.7
Fig. 5.8
Fig. 5.9
17
Glass Fronted Door Panels
The oven door front panels can be taken o so that the glass
panels can be cleaned. Move the cooker forward to gain
access to the sides (see the ‘Moving the Cooker’ section under
‘Installation’).
Open the oven door slightly and remove the front panel
xing screws from the door sides, two each side (Fig. 5.10).
Carefully lift o the outer door panel. The inside face of the
glass panels can now be cleaned – take care not to disturb or
wet the door insulation.
Note: If the door is triple glazed then the inner two panels are
xed together and should not be separated.
After cleaning, carefully ret the outer door panel and replace
the side xing screws.
DO NOT use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Ovens
‘Cook & Clean’ Panels
The main oven has panels which have been coated with a
special enamel that partly cleans itself. This does not stop
all marks on the lining, but helps to reduce the amount of
manual cleaning needed.
The ‘Cook & Clean’ panels work better above 200 °C. If you do
most of your cooking below this temperature, occasionally
remove the panels and wipe with a lint free cloth and hot
soapy water. The panels should then be dried and replaced
and the oven heated at 200 °C for about one hour. This
will make sure that the ‘Cook & Clean’ panels are working
eectively.
DO NOT use steel wool, oven cleaning pads, or any other
materials that will scratch the surface.
Removing the Main Oven Linings
Some of the lining panels can be removed for cleaning.
If you wish to clean the enamel interior of the oven, you
will need to remove the shelves before removing the ‘Cook
& Clean’ panels . You do not have to remove the support
brackets to remove the panels. Lift each panel upward and
slide forward o the support brackets (Fig. 5.11).
Once the panels have been removed, the oven enamel
interior can be cleaned.
Ret in the reverse order.
The Tall Oven
To clean the oven sides, slide out the shelves, unhook the
supports from the oven sides, and lift out (Fig. 5.12).
ArtNo.320-0002a Proplus oven door side screws
Fig. 5.10
Fig. 5.11
Fig. 5.12
18
Cleaning Table
Cleaners listed (Table 5.1) are available from supermarkets or
electrical retailers as stated.
For enamelled surfaces use a cleaner that is approved for use
on vitreous enamel.
Regular cleaning is recommended. For easier cleaning, wipe
up any spillages immediately.
Table 5.1
Hotplate
Part Finish Recommended Cleaning Method
Hob top (including burner heads and
caps)
Enamel, stainless steel,
aluminium
Hot soapy water, soft cloth. Any stubborn stains remove gently
with a nylon scourer.
Ceramic/Induction hob Toughened glass Hot soapy water; cream cleaner/scourer if necessary.
Griddle plate (some models only) Non-stick surface
Allow to cool. Wash in hot soapy water. Do not use abrasive
cleaners/scourers. Dishwasher.
Warming zone (some models only) Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Outside of Cooker
Part Finish Recommended Cleaning Method
Door, door surround and storage
drawer exterior
Enamel or paint
Hot soapy water, soft cloth.
Any stubborn stains, remove gently with a liquid detergent.
Stainless steel
E-cloth (electrical retailers) or microfibre all-purpose cloth
(supermarket).
Sides and plinth Painted surface Hot soapy water, soft cloth.
Splashback/rear grille Enamel or stainless steel Hot soapy water, soft cloth. Cream cleaner, with care, if necessary.
Control panel
Paint, enamel, stainless steel
or glass
Warm soapy water. Do not use abrasive cleaners on lettering.
Control knobs/handles & trims
Plastic/chrome, copper or
lacquered brass
Warm soapy water, soft cloth.
Brass Brass polish.
Oven door glass/glass lid Toughened glass Hot soapy water, cream cleaner/scourer if necessary.
Oven and Grill
Part Finish Recommended Cleaning Method
Sides, floor & roof of oven NOT
COOK & CLEAN OVEN PANELS (see
below)
Enamel
Any proprietary oven cleaner that is suitable for enamel.
CAUTION: CORROSIVE/CAUSTIC OVEN CLEANERS: FOLLOW
MANUFACTURER’S INSTRUCTIONS.
Do not allow contact with the oven elements.
Cook & Clean oven panels (some
models only)
Special enamel that partly
cleans itself
This surface cleans itself at 200 °C and above, or the panels can be
removed and washed with hot soapy water and a nylon brush (see
‘The Ovens’ in ‘Cleaning your Cooker’).
Oven shelves, Handyrack, grill
trivet, Handygrill rack
Chrome
An oven interior cleaner that is suitable for chrome. Soap filled
pad. Dishwasher.
Grill pan/meat tin (some models
only)
Enamel Hot soapy water. Soap filled pad. Dishwasher.
19
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated?
If not, there maybe something wrong with the power
supply.
Are the sparker (ignition electrode) or burner slots
blocked by debris.?
Are the burner trim and caps correctly located? See the
section on ‘Cleaning’.
Hotplate burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
Check that there is not a problem with your gas
supply. You can do this by making sure that other gas
appliances you may have are working.
Do the burners spark when you push the control?
If not, verify that the power is on by checking that the
clock is illuminated.
Steam is coming from the oven
When cooking foods with high water content (e.g. oven
fries) there may be some steam visible at the rear grille.
Take care when opening the oven door, as there may
be a momentary pu of steam when the oven door
is opened. Stand well back and allow any steam to
disperse.
What cleaning materials are recommended for the
cooker?
See the ‘Cleaning’ section for recommended cleaning
materials.
Never use caustic or abrasive cleaners as these will
damage the surface.
An oven fan is noisy
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
The knobs get hot when I use the oven or the grill. Can I
avoid this?
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open.
Make sure that the grill pan is pushed right back to the
‘back stop’ when grilling.
Always grill with the grill compartment door open.
The fascia gets hot when I use the oven or grill
The cooker is cooled by a fan. If the fascia becomes
excessively hot when the cooker is in use then the
cooling fan may have failed. Should this occur please
contact your installer, a qualied repair engineer or
Customer Service to arrange for its repair.
If there is an installation problem and I don’t get my
original installer to come back to x it who pays?
You do. Service organizations will charge for their call
outs if they are correcting work carried out by your
original installer. It is in your interest to track down your
original installer.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to make sure that the
timed oven continues to operate.
Fascia illumination is not coming on (Hi-LITE only)
Is the power on?
The appliance has developed a fault that cannot be
rectied by the user. Please contact your installer or a
qualied repair engineer.
Food is cooking too slowly, too quickly, or burning
Cooking times may dier from your previous oven.
Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. The oven control settings and cooking
times are intended to be used only as a guide.
Individual tastes may require the temperature to be
altered either way, to get the results you want.
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specied in the section on ‘General Oven Tips’.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, make sure that it is placed centrally on the
shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held rmly
against the seal.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level arrange for
your supplier to level it for you.
Oven not coming on
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply.
Is the cooker supply on at the isolator switch?
Has the time of day been set?
Is the key symbol [
] showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.
6. Troubleshooting
20
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake?
Is the oven locked (see above)?
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be tted by a service person.
An oven light is not working
The bulb has probably burnt out. You can buy a
replacement bulb (which is not covered under the
warranty) from a good electrical shop. Ask for a 15 W –
230 V lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C (Fig. 6.1).
Turn o the power at the circuit breaker.
Before removing the existing bulb, turn o the power
supply and make sure that the oven is cool. Open the
oven door and remove the oven shelves.
Unscrew the bulb cover by turning counter-clockwise. It
may be very sti (Fig. 6.2).
Taking care to protect your ngers with a glove in case
the bulb should shatter, unscrew the old bulb.
Screw in the new bulb; screw back the bulb cover. Turn
on the circuit breaker and check that the bulb now
lights.
The oven door is misaligned
The bottom hinge of either oven door can be adjusted
to alter the angle of the door (Fig. 6.3). Loosen the
bottom hinge xing screws and use the notch and a at
bladed screwdriver to move the position of the hinge to
set the hinge position (Fig. 6.4).
Retighten the hinge screws.
ArtNo.324-0005 Oven light bulb
ArtNo.320-0007 Oven door hinge adjustment 2
Eect of hinge adjustment – exaggerated for clarity
Oven door omitted for clarity
Centreline of hinge pin
Fig. 6.1
Fig. 6.2
Fig. 6.3
Fig. 6.4
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
21
Dear Installer
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
Safety Requirements and Regulations
This cooker must be installed in accordance with
the relevant instructions in this booklet, with the
relevant national and local regulations, and with
the local gas and electricity supply companies’
requirements.
This cooker is a Class 2 Subclass 1 appliance.
Before installation, make sure that the cooker is
suitable for your gas type and supply voltage. See
the data badge.
The appliance must be installed in accordance with
the regulations in force and only in a well-ventilated
space.
Read the instructions before installing or using this
appliance.
In your own interest and that of safety, it is law
that all gas appliances be installed by competent
persons. Failure to install the appliance correctly
could invalidate any warranty or liability claims and
lead to prosecution.
This appliance can be converted for use on another
gas.
In the UK the cooker must be installed in
accordance with:
• All relevant British Standards / Codes of Practice, in
particular BS 5440 Part 2.
• For Natural Gas – BS 6172 and BS 6891.
• For LP Gas – BS 5482-1 (when the installation is
in a permanent dwelling), BS 5482-2 (when the
installation is in a caravan or other non-permanent
dwelling) or BS 5482-3 (when the installation is in a
boat).
• The Gas Safety (Installation and Use) regulations.
• The relevant Building / IEE regulations.
In the Republic of Ireland the cooker must be
installed in accordance with:
The installation must be carried out by a competent person
and installed in accordance with the current edition of IS 813
“Domestic Gas Installations”, the current Building Regulations
and reference should be made to the current ETCI rules for
electrical installation.
Provision of Ventilation
This appliance is not connected to a combustion products
evacuation device. Particular attention shall be given to the
relevant requirements regarding ventilation.
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
In the UK:
The room containing the cooker should have an air supply
in accordance with BS 5440 Part 2. All rooms require an
openable window or equivalent, while some rooms require
a permanent vent in addition to the openable window. The
cooker should not be installed in a bedsitting room with
volume less than 20 m³. If it is installed in a room of volume
less than 5 m³ an air vent of eective area 100 cm² is required;
if it is installed in a room of volume between 5 m³ and 10 m³,
an air vent of eective area 50 cm² is required; while if the
volume exceeds 11 m³, no air vent is required.
If there are other fuel burning appliances in the same room,
BS 5440 Part 2 should be consulted to determine the requisite
air vent requirements.
In the Republic of Ireland:
Reference should be made to the current edition of IS 813,
which makes clear the conditions that must be met to
demonstrate that sucient ventilation is available.
ArtNo.050-0011 - Installer information table
Installer’s Name
Appliance Serial Number
Installer’s Telephone Number
Installer’s Company
7. Installation
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
22
Checking the Parts:
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
This appliance is designed for domestic cooking only. Use
for any other purpose could invalidate any warranty or
liability claim.
Note: An appliance for use on LPG must not be installed
in a room or internal space below ground level, e.g. in a
basement.
Conversion
This appliance is supplied set for G20 20 mbar Cat II
2H3+
.
A conversion kit for another gas is available for the cooker.
If the appliance is to be converted to another gas we
recommend that this is carried out before installation.
After converting the appliance, please attach the Gas
Conversion sticker over the appropriate area of the data
badge – this will identify the gas type for which the appliance
is now set.
You will need the following equipment to complete the
cooker installation satisfactorily:
• Stability bracket: If the cooker is to be supplied with
gas through a flexible hose, a stability bracket or chain
MUST be fitted.
These are not supplied with the cooker but are
available at most builders’ merchants.
• Gas pressure tester/manometer.
• Flexible gas hose: Must be in accordance with the
relevant standards.
• Multimeter: For electrical checks.
You will also need the following tools:
1. Electric drill
2. Masonry drill bit (only required if tting the cooker on a
stone or concrete oor)
3. Wall plugs (only required if tting the cooker on a stone
or concrete oor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. Spirit level
8. Pencil
9. Adjustable spanner
10. Screws for tting the stability bracket
11. 4 mm & 3 mm Allen keys
12. 13 mm spanner or socket wrench
3 pan supports Griddle
ArtNo.000-0001 90 Pan supports
Plinth (1-piece model shown) Grill pan & trivet
ArtNo.330-0001 - Grill pan
1 drop shelf
(not supplied with the Hi-LITE)
1 at shelf
Roasting tin Handyrack
ArtNo.324-0004 Roasting tin
ArtNo.324-0003 Handyrack
Tall oven shelves and shelf
supports (example shown)
Splashback (Classic only)
ArtNo.000-0010 Tall oven shelves
ArtNo.350-0012 - splashback
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
23
ArtNo.105-0008 - 100DF 2BC cooker min spacings
Professional +
905 mm min
930 mm max
75 mm
min
75 mm
min
650 mm
min
130 mm min
Positioning the Cooker
Fig. 7.1 and Fig. 7.2 show the minimum recommended
distance from the cooker to nearby surfaces.
The cooker should not be placed on a base.
Above hotplate surround should be level with, or above, any
adjacent work surface.
A gap of 75 mm should be left between each side of the
cooker ABOVE the hotplate level and any adjacent vertical
surface.
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25 mm.
A minimum space of 650 mm is required between the top of
the hotplate and a horizontal combustible surface.
*Any cookerhood should be installed in accordance with the
hood manufacturer’s instructions.
**Any splashback must be tted in accordance with the
manufacturers instructions. Allowance should be made for the
additional height of the ue trim, which is tted to the cooker
hob.
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration.
We cannot accept responsibility for damage caused by
normal use of the cooker to any material that de-laminates
or discolours at temperatures less than 65 °C above room
temperature.
We recommend a gap of 1010 mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
If the cooker is near a corner of the kitchen, a clearance of
130 mm is required to allow the oven doors to open (Fig. 7.3).
The actual opening of the doors is slightly less but this allows
for some protection of your hand as you open the door.
Moving the Cooker
On no account try and move the cooker while it is
plugged into the electricity supply.
The cooker is very heavy, so take great care.
We recommend that two people manoeuvre the cooker.
Make sure that the oor covering is rmly xed, or removed,
to prevent it being disturbed when moving the cooker
around.
To help you, there are two levelling rollers at the back, and
two screw-down levelling feet at the front.
Remove the polystyrene base pack. From the front, tilt the
cooker forward and remove the front half of the polystyrene
base (Fig. 7.4). Repeat from the back and remove the rear
half of the polystyrene base.
ArtNo.105-0009-100DF-2BC Min distances above cooker
**
1000 mm min*
410 mm min
5 mm5 mm
Fig. 7.1
Fig. 7.2
Fig. 7.3
Fig. 7.4
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
24
ArtNo.070-0014 - Stability bracket - Wall fitting
Cooker
Stability bracket
Floor
3 mm min
Typical oor mounting
Typical oor mounting
Cooker
Outer stability
bracket
Floor
Wall
3 mm min
Typical wall mounting
Typical wall mounting
Stability chain
ArtNo.010-0004 Moving the cooker
Lowering the Two Rear Rollers
To adjust the height of the rear of the cooker, rst t a 13 mm
spanner or socket wrench onto the hexagonal adjusting
nut (Fig. 7.5). Rotate the nut – clockwise to raise – counterclockwise to lower.
Make 10 complete (360°) turns clockwise.
Make sure you lower BOTH REAR ROLLERS.
Completing the Move
Unfold the rear edge of the pack base tray. Open the grill
door and right-hand oven door so that you can get a good
grip on the bottom of the fascia panel as you move the oven
(Fig. 7.6).
Carefully push the cooker backwards o the cardboard base.
Remove the pack base tray.
Position the cooker close to its nal position, leaving just
enough space to get behind it.
Do not use the door handles or control knobs to
manoeuvre the cooker.
Fitting the Stability Bracket or Chain
Unless otherwise stated, a cooker using a exible gas
connector must be secured with a suitable stability device.
Suitable stability devices are shown in Fig. 7.7, Fig. 7.8 and
Fig. 7.9.
If you are using a stability chain (Fig. 7.7) then the chain
should be kept as short as is practicable and xed rmly to
the rear of the cooker.
If you are using a stability bracket (Fig. 7.8) and (Fig. 7.9),
then adjust the bracket to give the smallest practicable
clearance between the bracket and the engagement slot in
the rear of the cooker.
Fit the bracket so that it engages as far as possible over the
chassis of the cooker.
Repositioning the Cooker Following
Connection
If you need to move the cooker once it has been connected
then you need to unplug it and, having gripped under the
fascia panel and lifted the front of the cooker slightly
(Fig. 7.6), you need to check behind the cooker to make sure
that the gas hose is not caught.
As you progress, make sure that both the electricity cable and
gas hose always have sucient slack to allow the cooker to
move.
With a stability chain tted, release it as you ease the cooker out.
Do not forget to ret it when you replace the cooker.
When you replace the cooker, again check behind to make
sure that the electricity cable and gas hose are not caught or
trapped.
Fig. 7.5
Fig. 7.6
Fig. 7.7
Fig. 7.8
Fig. 7.9
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
25
Conversion to Another Gas
If the appliance is to be converted to another gas do the
conversion at this point. See the conversion section of these
instructions.
Levelling
You are recommended to use a spirit level on a shelf in one of
the ovens to check for level.
Place the cooker in its intended position, taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level the
cooker.
To adjust the height of the rear of the cooker use a 13 mm
spanner or socket wrench to turn the adjusting nuts at the
front bottom corners of the cooker.
To set the front, turn the feet bases to raise or lower.
Gas Connection
This must be in accordance with the relevant standards.
The exible hose (not supplied with the cooker) must be
in accordance with the relevant standards. Hoses may be
purchased at most builders’ merchants.
We recommend that a Micropoint gas hose is used when
installing this appliance.
The gas supply needs to terminate with a side-facing elbow
with a down-facing bayonet.
The connector is located just below the hotplate level at the
rear of the cooker. If in doubt contact your supplier.
The rear cover boxes limit the position of the supply point.
Because the height of the cooker can be adjusted and
each connection is dierent, it is dicult to give precise
dimensions.
Although a 900 mm hose can be used (on the Hi-LITE model
we recommend a 1250 mm hose), a 1250 mm hose will allow
slightly more exibility in the positioning of the bayonet and
make moving the cooker easier.
The hose should be tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape.
Ideally the hose supply connection should be within the
shaded area ‘A’ (Fig. 7.10 or Fig. 7.11 on Hi-LITE & Classic
models).
For Natural Gas, the exible hose must be in accordance with
BS 669. For LP Gas, it should be capable of 50 mbar pressure,
70 °C temperature rise, and carry a red stripe, band or label. If
in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet.
After completing the gas connection, make sure that the
cooker is gas sound with a pressure test.
680
450
750
A
500
All dimensions in millimetres
Gas inlet
290
130
370
140
225
A
30
Gas inlet
All dimensions in millimetres
Fig. 7.10
Fig. 7.11
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
26
Pressure Testing
The gas pressure can be measured at one of the hotplate
burner injectors (not the wok burner).
Lift o a burner head. Fit the pressure gauge to the injector.
Turn on and light one of the other hotplate burners.
Turn on the control knob for the burner with the pressure
gauge tted to let gas through.
See the data badge for test pressures.
Turn o the burners. Make sure that you reassemble the
burner top in the correct way on the burner body.
Electrical Connection
The cooker must be installed by a qualied electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
Current Operated Earth Leakage Breakers
The combined use of your cooker and other domestic
appliances may cause nuisance tripping, so we
recommend that the cooker is protected on an individual
RCD (Residual Current Device) or RCBO (Residual Current
Breaker with Overload).
IF IN DOUBT, PLEASE CONSULT A SUITABLY QUALIFIED
ELECTRICIAN.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double-pole
switch, having a contact separation of at least 3 mm in all
poles.
The cooker MUST NOT be connected to an ordinary
domestic power point.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your electrical
supply type (Fig. 7.12 and Fig. 7.13). Check that the links are
correctly tted and that the terminal screws are tight. Secure
the mains cable using the cable clamp.
ArtNo.130-0010 Electrical connections single-phase
L
N
230 V ac 50 Hz
10 mm² max
6 mm² max
L1
N
L3
L2
3N ac
230/400 V 50 Hz
6 mm² max
10 mm² max
6 mm² max
Fig. 7.12
Fig. 7.13
INSTALLATION
Check the appliance is electrically safe and gas sound when you have nished.
27
ArtNo.350-0012 - Securing the plinth
Final Checks
Hotplate Check
Check each burner in turn (refer to the ‘Hotplate Burners’
section at the front of the instructions).
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Set the clock as described earlier in the instructions, and then
turn on the ovens. Check that the oven fans start to turn and
that the ovens start to heat up.
Note: The oven light bulb is not included in the guarantee.
Turn o the oven.
Fitting the Plinth
Fitting the 1-piece Plinth (Classic & Professional+)
Loosen the three screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw. Twist
and t each end keyhole over their respective screws. Tighten
the xing screws (Fig. 7.14).
Fitting the 2-piece Plinth (Kitchener & Hi-LITE)
Fit the inner plinth to the bottom front of the cooker using
the 4 or 5 screws provided (Fig. 7.15).
Kitchener: Fit the outer plinth (2 screws, 1 each end) to the
inner plinth. The height of the outer plinth can be adjusted by
sliding it up or down via the slotted hole (Fig. 7.16).
Hi-LITE: Oer the keyhole slots on the outer plinth to the
location points on the inner plinth (Fig. 7.17)
When released the outer plinth should automatically adjust
to the oor height (Fig. 7.17).
WARNING: When moving the cooker ensure that the
outer plinth is removed. Failure to do so may result
in damage to plinth and oor.
Customer Care
Installer: Please complete your details in this guide, inform
the user how to operate the cooker and hand over the
instructions.
Thank you.
ArtNo.350-0010 - Fitting the plinth 1 (Kitchener)
ArtNo.350-0011 - Fitting the plinth 2 (Kitchener)
Outer plinth
Outer plinth xing screw
Inner plinth
Fig. 7.14
Fig. 7.15
Fig. 7.16
Fig. 7.17
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.
28
A
B
C
ArtNo.311-0010 Injectors
A – Jet, B – Internal injector, C – External injector
ArtNo.270-0032 - 90 Prof+ FX - Removing the control panel
Professional + 100 FX
Check the ‘Technical Data’ section at the back of the book
that the hob is convertible to the gas you want to use.
A suitably competent person must perform the conversion.
After conversion the installation must comply with the
relevant regulations and also the local electricity supply
company requirements. Read the instructions before
converting this appliance.
Failure to convert the appliance correctly could
invalidate any warranty or liability claims and lead
to prosecution.
When servicing or replacing gas-carrying
components disconnect from the gas supply before
starting operation. Check the appliance is gas sound
after completion.
DO NOT use reconditioned or unauthorised gas
controls.
Disconnect from the electricity supply before
servicing.
Before electrical reconnection, check that the
appliance is electrically safe.
Injectors
Remove the burner caps and heads. Remove the old jets
(Fig. 8.1). Fit the new jets (see ‘Technical Data’ section at the
back of the book for correct jets). Reassemble in the reverse
order.
Tap Adjustment
Removing the Control Panel
Pull o all the control knobs. Remove the three xing screws
underneath the control panel (Fig. 8.2).
The control panel will drop down slightly. It is held at the top
by two holes in the top edge, one at each end, that locate on
the tags on the inner panel. Lift the control panel clear of the
tags and pull forwards, taking care not to damage or strain
the wiring.
Bypass Screw Adjustment
Turn the bypass screw on each control clockwise to the stop
(Fig. 8.3).
Stick on Label
Stick the LP gas label over the natural gas part of the
appliance data label.
ArtNo.0102-0011 - Screwing
the control valve bypass screw
8. Conversion to LP Gas
Fig. 8.1
Fig. 8.2
Fig. 8.3
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have nished.
29
Pressure Testing
Connect the appliance to the gas supply.
Connect the appliance to the gas supply. Check the appliance
is gas sound.
The gas pressure can be measured at one of the left hand
hotplate burner jets. Lift o a burner head. Fit the pressure
gauge to the jet. Turn on and light one of the other burners
with a match. Turn on and press in the control knob for the
burner with the pressure gauge tted.
The pressure should be 29 mbar for Butane and 37 mbar for
Propane. After checking the pressure, turn o the taps and
replace the burner head.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Check the appliance is gas sound.
Check operation of all the burners.
30
9. Circuit Diagram
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
C
B1
D1
A2
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
g/y
bk
r
b
b
b
g/y
or
br
w
b
r
y
r
y
r
bk
b
v
br
bk
br
r
b
gr
w
b
b
b
b
br
b
b
b
b
b
b
br
v
r
r
v
br
r
br
y
y
r
v
or
v
v
v
br
v
r
r
br
v
r
r
v
br
gr
v
r
r
r
r
b
v
b
r
b
r
bk
v
r
v
r
g/y
b
b
w
y
r
A1
C
B1
B2
B4
D2
G
D1
D3
D4
F1
I
F2
H
A3A2A4
B3
J
L
I
I
K
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Circuit Diagram: Classic
Code Colour
b Blue
br Brown
bk Black
or Orange
r Red
v Violet
w White
y Yellow
g/y Green/yellow
gr Grey
Code Description
A1 Grill Front Switch
A2 Grill Energy Regulator
A3 Grill Elements -LH
A4 Grill Elements - RH
B1 Left-Hand Oven Thermostat
B2 Left Hand Oven Front Switch
B3 Left Hand Oven Fan Element
B4 Left Hand Oven Fan
C Clock / Timer
Code Description
D1 Right - Hand Oven Thermostat
D2 Right - Hand Oven Front Switch
D3 Right- Hand Oven Element
D4 Right - Hand Oven Fan
F1 Left - Hand Oven Thermal Preset
F2 Right - Hand Oven Thermal Preset
G Left Hand Oven Light
H Cooling Fan
I Indicator Neon
J Ignition Switch
K Oven Light Switch
L Spark Generator
31
a
b
e
f
c
d
1
2
P095199
1
2
P2
P1
E
1
2
1
2
P095199
1
2
P2
P1
b
b
b
or
or
bk
v
v
bk
bk
r
r
r
br
br
r
y
y
y
w
w
w
b
b
y
br
br
br
b
b
b
b
y
y
y
or
or
w
w
b
bk
bk
br
br
br
br
y
y
y
y
b
b
gy
b b b b b
br
br
br
gy
br
br
A1
A2
B1
C
D1
D2
D3
D4
F1
F2
G1
H
I
B2
B3
B4
G2
H
H
I
A3
J
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Colour
b Blue
br Brown
bk Black
or Orange
r Red
v Violet
w White
y Yellow
g/y Green/yellow
gr Grey
Code Description
A1 Grill control
A2 Grill element right-hand side
A3 Grill element left-hand side
B1 Left-hand fan oven thermostat
B2 Left-hand fan oven control
B3 Left-hand fan oven element
B4 Left-hand fan oven fan
C Clock
D1 Right-hand fan oven thermostat
D2 Right-hand fan oven control
D3 Right-hand fan oven element
D4 Right-hand fan oven fan
Code Description
F1 Oven light switch
F2 Oven lamp
G1 Ignition switch
G2 Ignition spark generator
H Neon
I Thermal cut-out
J Cooling fan
Circuit Diagram: Professional+ & Kitchener
32
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
g/y
w
bk
r
b
b
b
g/y
bk
br
or
br
w
b
r
br
b
y
r
y
r
bk
b
v
br
br
bk
br
r
b
b
gr
b
w
b
b
b
b
br
b
b
b
b
b
b
br
r
b
v
r
r
y
v
br
r
br
y
y
r
v
or
v
v
v
v
br
v
r
r
br
br
br
v
r
r
v
br
gr
v
A1
C
B
A
B1
B2
B4
D2
G
D1
D3
D4
F1
I
F2
H
A3A2A4
B3
J
K
L
M1
M2
M3
E
P095199
1
2
P2
P1
v
P095199
1
2
P2
P1
P095199
1
2
P2
P1
a
b
e
f
c
d
1
2
g/y
w
bk
r
b
b
b
g/y
bk
br
or
br
w
b
r
br
b
y
r
y
r
bk
b
v
br
br
bk
br
r
b
b
gr
b
w
b
b
b
b
br
b
b
b
b
b
b
br
r
b
v
r
r
y
v
br
r
br
y
y
r
v
or
v
v
v
v
br
v
r
r
br
br
br
v
r
r
v
br
gr
v
A1
C
B
A
B1
B2
B4
D2
G
D1
D3
D4
F1
I
F2
H
A3A2A4
B3
J
K
L
M1
M2
M3
Circuit Diagram: Hi-Lite Fan Oven
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230 V 50 Hz.
Code Colour
b Blue
br Brown
bk Black
or Orange
r Red
v Violet
w White
y Yellow
g/y Green/yellow
gr Grey
Code Description
A Illumination board - left-hand side
A1 Grill front switch
A2 Grill energy regulator
A3 Left-hand grill element
A4 Right-hand grill element
B Illumination board - right-hand side
B1 Left-hand oven thermostat
B2 Left-hand front switch
B3 Left-hand oven element
B4 Left-hand oven fan
F1 Left-hand oven thermal preset
C Clock
Code Description
D1 Right-hand oven thermostat
D2 Right-hand oven front switch
D3 Right-hand oven element
D4 Right-hand oven fan
F2 Right-hand oven thermal preset
G Oven light
H Cooling fan
J Illumination switch
K Oven light switch
M1 Grill heat indicator
M2 Left-hand oven heat indicator
M3 Right-hand oven heat indicator
33
10. Technical Data
THE COOKER IS CATEGORY: Cat II
2H3+
.
It is supplied set for group H natural gas. A conversion kit from NG to LP is available for the cooker.
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION: Cooker back, serial number repeater badge below oven door opening.
COUNTRY OF DESTINATION: GB, IE.
Connections
Gas (Rp ½ at rear right-hand side) Electric
Natural gas
20 mbar
230/400 V 50 H zButane 29 mbar
Propane 37 mbar
See the appliance badge for test pressures.
Dimensions
Overall height minimum 905 mm maximum 930 mm
Overall width 994 mm
Overall depth: Kitchener 653 mm including handles; 605 mm excluding handles
Overall depth: Classic 667 mm including handles; 605 mm excluding handles
Overall depth: Hi-LITE
650 mm including handles; 605 mm excluding handles
Refer to 'Positioning the Cooker'.
Ratings
Hotplate
Bypass
Screw*
Natural Gas 20 mb L.P. Gas
Injector Injector
Wok burner 57
3.5 kW
internal 78
3.5 kW (246 g/h)
internal 53
external 126 external 82
Large burner 40
3.0 kW 134 3.0 kW (210 g/h) 87
Medium burner 32
1.7 kW 109 1.7 kW (119 g/h) 68
Small burner 28
1.0 kW 75 1.0 kW (70 g/h) 51
* The valves in this cooker are fitted with adjustable bypass screws. The cooker is supplied with the bypass screws set for
Natural gas. For LPG conversion the bypass screws must be screwed all the way down.
Oven Efficiency
Ovens
Main Oven Tall Oven
Forced Air Convection Forced Air Convection
Maximum output 2.5 kW 2.5 kW
Energy eciency class on a scale of A (more ecient) to G (less ecient) A A
Energy consumption based on standard load
0.90 kWh 0.99 kWh
Oven volume (litres) 69 81
Size Large Large
Time to cook standard load 38 minutes 48 minutes
Surface area of the grid
1400 cm
2
1056 cm
2
Grill 2.3 kW
Maximum total electrical load at 230 V (approximate total including oven lights, oven fan, etc.): 7.4 kW.
ArtNo.105-0008 - Technical data - 90 induction - Elan
34
Notes
CONSUMER SERVICE
If you have any product enquiries, or in the event of a problem
with your appliance once it has been installed, please telephone:
0800 804 6261 or depending on your mobile network tari you can
call free on 0370 789 5107.
CONSUMER SERVICE LINES OPEN:
Monday to Thursday 8am–6pm
Friday 8am–5pm
Saturday 9am–1pm
WARRANTY
Your manufacturer warranty covers goods of our own brand for
defective workmanship and materials for a period of 1 year from the
date of purchase. This warranty covers mechanical breakdown and
proven cosmetic and manufacturing defects.
You will receive an additional FREE full 12 months guarantee by
registering your purchase using the FREEPOST form provided.
Alternatively, call free on 0800 587 5747, quoting reference
RMGX57A, or register online at www.rangemaster.co.uk.
Any damage, blemishes or chips identied upon receipt of the
product must be reported within 90 days. Proof of purchase may
be required to establish validity. Scratches on the surface of ceramic
hobs must be reported within 14 days. Scratches caused by usage are
not covered. Accidental damage is not covered by the manufacturer’s
warranty.
For warranty compliance, the requirements for the appliance are:
• Has been correctly installed in accordance with current legislation,
relevant British and European Standards and Codes of Practice, by
a suitably competent person registered with Gas Safe or equivalent
body and where applicable a qualied electrician.
• Has been used solely for domestic cooking purposes.
• If in use in the UK*, has not been taken abroad as a personal
export. In the Republic of Ireland, conditions may vary, so consult
your retailer.
• Is not second-hand or a refurbished appliance. The manufacturer’s
warranty is not transferable.
• Has not been subject to misuse, accidental damage or modication,
and has not deteriorated due to normal domestic wear and tear,
and the manufacturer’s recommendations concerning cleaning
materials have been followed.
• Has not been repaired by persons or organisations other than
those authorised to act on behalf of AGA Rangemaster.
Exceptions:
• Items not included under the free 1 year warranty include pan
supports, griddles, wok rings, baking trays, grill pans, trivets, lters,
light bulbs and other consumable accessories.
• Any damage caused other than through normal use.
• Breakdowns associated with cooking spillage.
• Cosmetic deterioration deemed to be normal wear and tear.
• Please note that we reserve the right to charge additional payments
for engineer’s expenses, at our discretion, up to the value of £300
per home visit.
• The terms of this warranty are in addition to your legal rights and
do not aect your legal rights in relation to defective products.
Please contact Citizen’s Advice for more information relating to
your legal rights.
* Only certain models can be adapted for use with Mains Gas
supplied in the Channel Islands and Isle of Man.
OUT OF WARRANTY
Service work should only be carried out by technically competent
and suitably qualied personnel.
For your own safety, always make sure that work is carried out by
a Gas Safe registered engineer for gas appliances or an approved
electrician for electrical models.
For a competitive quote and to arrange for a Rangemaster approved
engineer to attend, call Consumer Services on: 0800 804 6261 or
depending on your mobile network tari you can call free on 0370
789 5107.
SPARE PARTS
To maintain optimum and safe performance, we recommend that
only genuine Rangemaster spare parts are used. These are available
from most major spares stockists, including ourselves.
STANDARDS
Rangemaster cookers are designed and manufactured to a recognised
international quality standard, which meets the requirements of
BS EN ISO 9001, BS EN ISO 14001 and OHSAS 18001 for continually
improving environmental procedures.
Rangemaster cookers comply with the essential requirements of the
appropriate European Directives, and carry the CE mark.
Name of Appliance & Colour*
Appliance Serial Number*
Fuel Type*
Natural Gas
LP Gas
Dual Fuel Electric
Retailer’s Name & Address
Date of Purchase
Installer’s Name & Address
Installer’s Telephone Number
Date of Installation
* This information is on the appliance data badge - look in the appliance
instructions to nd out where the data badge is located.
Britain’s No.1 Range Cooker
Clarence Street
Royal Leamington Spa
Warwickshire
CV31 2AD
England
Tel: +44 (0) 1926 457400
Fax: +44 (0)1926 450526
E-mail: consumers@rangemaster.co.uk
Consumer Services Tel: +44 (0) 800 804 6261
www.rangemaster.co.uk
For ROI Enquiries Tel: 1850 302 502
Registered in England and Wales. Registration No. 354715 Registered Oce: Juno Drive, Leamington Spa, Warwickshire, CV31 3RG
Search Rangemaster UK
Rangemaster continuously seeks improvements in specication, design and production of products and thus, alterations take place periodically. Whilst every eort is made to produce up-to-date literature, this booklet should not be regarded as an infallible guide to current
specication, nor does it constitute an oer for the sale of any particular appliance.
ALSO PART OF THE RANGEMASTER COLLECTION...
Refrigeration Built-in Cooking
Dishwashing Sinks & Taps
Loading...