RAMSET MODEL TF1100
TrakFast
OPERATOR’S SAFETY & OPERATING
INSTRUCTION MANUAL
DANGER
READ AND OBEY ALL SAFETY AND OPERATING
INSTRUCTIONS BEFORE OPERATING TOOL.
Introduction ............................................................... 2
An Overview of the TrakFast Tool .............................................. 3
Safety Instructions ......................................................... 4-6
Battery and Charging System ................................................ 7-8
Fuel Cell and Metering Valve ................................................ 9-10
Preparing and Use of the TrakFast Tool .........................................11
Servicing ............................................................... 12-13
Troubleshooting ......................................................... 14-16
Warranty ..................................................................17
TRAKFAST TOOL OPERATING MANUAL
This manual is intended to acquaint you with Ramset’s TrakFast tool. Unlike other power
fastening tools, the TrakFast tool is powered by an linear internal combustion motor. In
simpler terms, your TrakFast tool is powered by a motor similar to the one that powers an
automobile. The tool ignites a fuel and air mixture to produce the energy to drive the motor,
which in turn drives the fastener. As you will see, the TrakFast tool is totally self-contained.
It carries its own fuel supply and battery, along with a supply of fasteners.
For ease of use, this manual is divided into sections (see Table of Contents). Each section
of the manual is written with you, the tool operator, in mind. We have left out all of the
technical terms so that you can readily understand how to get the maximum performance
from your TrakFast tool, and how to avoid damaging the tool or injuring yourself. But, to
accomplish this, we need you to do two things:
1. READ THE MANUAL FROM COVER TO COVER BEFORE USING THE TOOL.
2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.
The TrakFast tool should be handled like other power fastening tools that you use. When
used properly, it will meet your fastening needs. And, like most of your tools, when used
improperly it can cause injury. If you are going to allow others to use the TrakFast tool, it is
your responsibility to make sure that they also read and comply with the instructions in this
manual before attempting to operate the tool.
Should you have questions about the TrakFast system, or wish to obtain additional copies
of this manual, please feel free to contact your Ramset Distributor Sales Representative.
TABLE OF CONTENTS / INTRODUCTION
TABLE OF CONTENTS / INTRODUCTION
2
DESCRIPTION
The TrakFast tool is a self-contained, fully
portable tool that uses liquid hydrocarbon
fuel to power a unique linear drive internal
combustion motor.
In order for you to fully understand the
information contained in this manual, you
need a basic understanding of the tool. As
you can see in the illustration below, the
TrakFast tool is made up of three assemblies:
the Handle, the Motor, and the Magazine.
As you examine the TrakFast tool, become
familiar with the three major assemblies
and the various components located in
each of them.
The Handle Assembly contains the Fuel
Cell, the Battery Voltage Indicator Light,
and the Trigger.
The Motor Assembly contains the Cover
and Filter, the Motor Housing, the Nose,
and the Work Contacting Element.
The Magazine Assembly contains the
Magazine Locking Knob, the Battery
Compartment, the Follower Release
Lever, the Follower, and the Lockout Bar.
SPECIFICATIONS
Dimension: Height 15.5 inches
Length 17 inches
Weight: 8.375 pounds
Cycle Rate: Intermittent Operation 2 to 3
pins per second Continuous Operation 1000
pins per hour
NOTE: Exceeding these rates could cause
the tool to overheat, resulting in loss of
performance or damage to tool components.
By using the TrakFast tool at its recommended operation rate you will be able to
drive several
thousand fasteners in a typical
workday.
Maximum Fastener Length:
1-1/2 inch x .109 dia. shank
Magazine Capacity: 42 fasteners.
Battery Cell: 6 volts D.C.—Provides enough
energy to drive approximately 3000 fasteners
on a full charge.
Fuel Cell: Liquid hydrocarbon—Provides
enough fuel to drive up to 1000 fasteners.
AN OVERVIEW OF THE TRAKFAST TOOL
3
AN OVERVIEW OF THE TRAKFAST TOOL
Fuel Cell
Compartment
Magazine
Locking Knob
Battery Compartment
(opposite side)
Follower
Release Lever
Follower
Lockout Bar
Nose
Motor
Housing
Cover and
Filters
HANDLE
ASSEMBLY
MOTOR
ASSEMBLY
MAGAZINE
ASSEMBLY
Battery Voltage
Indicator Light (on
right side of handle)
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
4
The following safety instructions have been
included in this manual to provide you with
basic information necessary for safe operation
of the TrakFast Tool. DO NOT ATTEMPT TO
OPERATE THIS TOOL UNTIL YOU READ AND
UNDERSTAND ALL SAFETY PRECAUTIONS
AND MANUAL INSTRUCTIONS.
Failure to follow all safety precautions and
manual instructions can result in blindness,
severe personal injury, damage to personal
property, and damage to the tool.
In addition to these instructions, additional
training may be necessary, depending
upon the type of fastening you wish to
do. Contact your Ramset Distributor
Representative for additional information.
DANGER
Do not attempt to operate
this tool until you have read
and understood all safety
precautions and manual
instructions.
Failure to follow all safety precautions and
instructions may result in a permanent loss
of vision, serious personal or even fatal injury,
property damage and/or tool damage.
The TrakFast Tool is an
internal combustion device.
It produces hot exhaust
gases that may ignite
flammable materials. This tool must not be
used in a combustible environment or in the
presence of combustible materials, such as
flammable chemicals, adhesives, gasoline,
or solvents.
Do not expose the tool to
temperatures in excess of
120°F (49°C). Fuel and/or
the battery may burst,
releasing flammable gas.
This tool must be operated
only in a well-ventilated
environment,
because the
tool exhausts carbon
monoxide similar to a
gas chainsaw or lawnmower. Exposure
to carbon monoxide may cause dizziness,
nausea, or unconsciousness.
ALWAYS keep the TrakFast
Tool, fuel cell, battery cell
and battery charger out
of the reach of children.
1. READ THIS MANUAL FROM COVER
TO COVER. Always turn to this manual
for information about the safe operation
and servicing of the TrakFast tool. If any
portion seems unclear, or you have any
questions, contact your Ramset Distributor
Representative immediately.
2. WEAR EYE AND
HEARING PROTECTION.
Always wear hearing and
eye protection devices
when you are operating
the TrakFast tool or
working in the vicinity of this tool. Also, your
eye protection must meet the
requirement
of ANSI Standard Z87, and should
have side
shields for increased protection.
3. NEVER ASSUME THE TOOL IS EMPTY.
Every time you pick up the TrakFast tool,
check the Magazine for fasteners. Never
point the tool at anyone or yourself, even
if you are absolutely sure there are no
fasteners in the tool. The fastener you did
not see is the fastener that can injure you
or someone else.
4. NEVER ENGAGE IN “HORSEPLAY”
WITH THE TOOL. The TrakFast tool is not
a toy. . . it is a power fastening tool. It is
designed to drive a fastener through steel
sheets into concrete. To accomplish this
task, it generates a tremendous amount
of energy. Fooling around, even when you
are absolutely sure there are no fasteners
in the tool, is asking for an accident.
5. NEVER CARRY THE TOOL WITH
YOUR FINGER ON, OR DEPRESSING,
THE TRIGGER. You must remember that
the TrakFast tool operates in a specific
sequence. The Work Contacting Element
acts as an operating feature that blocks the
Trigger from completing the ignition circuit.
Should you unintentionally depress the
Work Contacting Element while pulling
the Trigger as you are carrying the tool...
it could discharge a fastener.
6. NEVER OPERATE A TOOL THAT IS
MALFUNCTIONING. If you determine that
the TrakFast tool is not working properly,
and the problem is more than a simple
fastener jam, stop using it immediately and
refer to the Servicing Section of this manual.
If the problem cannot be corrected with one
of the steps covered in the Servicing Section,
report the problem to your supervisor or
Ramset Distributor representative.
Do not attempt to make any additional
repairs to the TrakFast tool.
7. OPERATE THE TOOL ONLY ON THE
WORK SURFACE. The
TrakFast tool should be
operated only when it is
in contact with the work
surface. Always hold the
tool firm and perpendicular
against the surface to be fastened.
8. NEVER DISABLE OR REMOVE THE
WORK CONTACTING ELEMENT. The
TrakFast tool is equipped with a device
called the Work Contacting Element.
This device helps reduce the possibility
of accidental operation by preventing the
tool from operating until it is fully depressed
on the work surface. The Work Contacting
Element must never be disabled or removed.
Do not use the TrakFast tool if the Work
Contacting Element is not working properly.
9. DO NOT LOAD FASTENERS WITH
THE TRIGGER OR WORK CONTACTING
ELEMENT DEPRESSED. When loading
fasteners into the TrakFast tool, you must
avoid pulling the Trigger or while having the
Work Contacting Element depressed. When
the tool is placed on a bench or other surface,
the Work Contacting Element might be
depressed. When you are loading fasteners,
you could accidentally pull the Trigger by
grasping the Handle to steady the tool.
These two actions will cause the TrakFast
tool to operate, discharging a fastener.
10. FASTENER REMOVAL OR CLEARING
JAMS. With the TrakFast tool pointed away
from you and others, pull the Follower back
slightly and push the Release Lever. Tip the
tool Nose up slightly, and the fasteners will
slide out the rear of the Magazine. If you
have a jammed fastener, or other problem
with the operation of your TrakFast tool you
should stop attempting to use the tool and
refer immediately to the Servicing Section of
the manual.
11. NEVER ATTEMPT TO OPERATE THE
TRAKFAST TOOL IF PARTS ARE LOOSE,
DAMAGED, OR MISSING. Make sure all
screws and nuts are properly tightened and
all parts are properly installed and in good
working order. If parts are missing, don’t
attempt to make temporary repairs...contact
your Sales Representative immediately.
12. NEVER DRIVE FASTENERS ON TOP
OF OTHER FASTENERS OR TOO CLOSE
TO OTHER FASTENERS. Fastening on top
of or too close to other fasteners can cause
the fastener to ricochet and cause serious
injury. Fasten only in areas where the entire
shank can penetrate.
13. NEVER FASTEN INTO INAPPROPIATE
BASE MATERIAL. Materials such as hardened
steel, the web or edge of an I-beam, or steel
that is too thick may cause the fastener to
bend and or break and could cause serious
injury. Ramset performance data offers a
guideline of appropriate base materials and
thicknesses.
14. NEVER FIRE INTO VERY HARD OR
BRITTLE MATERIALS SUCH AS CAST
IRON, TILE, GLASS, OR ROCK. These
materials can shatter, causing sharp
fragments and/or the fastener to fly freely.
SAFETY INSTRUCTIONS
5
SAFETY INSTRUCTIONS
15. ALWAYS FOLLOW MINIMUM
FASTENER EDGE DISTANCE AND
SPACING REQUIREMENTS. The minimum
edge distance and spacing requirement for
concrete base materials is three-inches.
The minimum edge distance for steel base
material is ½-inch. The minimum spacing
for steel base materials is 1-1/2-inches.
Fasteners installed closer to one another
or to the edge may cause damage to the
base material or result in a loss of fastener
performance.
16. NEVER CARRY FASTENERS OR
OTHER HARD OBJECTS IN THE SAME
POCKET OR CONTAINER WITH FUEL
CELL. The Fuel Cell could be punctured,
causing serious injury.
17. NEVER ALLOW ANYONE TO USE THE
TRAKFAST TOOL UNLESS THEY READ
AND UNDERSTAND THE TOOL MANUAL
AND ALL SAFETY INSTRUCTIONS. It is
the tool owner’s responsibility to make sure
that all TrakFast tool users read and fully
understand all tool operation, safety and
maintenance instructions.
18. FUEL CELL
STORAGE. Fuel
Cells contain
flammable gases
which are under
pressure and must
be stored in an area
where they will not be exposed to an open
flame, sparks, or temperatures above 120°
Fahrenheit (49° Centigrade). Exposure to
temperatures above 120°F (49°C) may
cause the Fuel Cells to leak or burst,
releasing the flammable gases and
creating a risk of fire or explosion.
19. FUEL CELL DISPOSAL. Never attempt
to puncture, crush, burn or refill a Fuel Cell.
Always dispose of empty Cells with trash
that will not be burned. Also, never place the
Fuel Cell with other materials for reclamation
or recycling.
20. TOOL STORAGE. At the end of every
workday, remove the Battery Cell and store
it in the carrying case. Recharge the Cell
only if required as indicated by a red charge
light in the handle.
21. KEEP THE TOOL CLEAN. At the end
of each work day, take a minute to wipe the
TrakFast tool with a clean rag. A dirty tool is
more likely to jam or malfunction.
22. NEVER PLACE
YOUR HAND OR
FINGERS OVER THE
NOSE OF THE TOOL.
The fastener or piston
can seriously injure your
hand in the event of an accidental discharge.
SAFETY INSTRUCTIONS
6
SAFETY INSTRUCTIONS
BATTERY CELL AND CHARGER
The first step in preparing a new tool for
operation is to fully charge the new Battery.
New Batteries are shipped discharged and
must be charged for 24 hours before first
use. All subsequent charges will require at
most a 3 hour charge.
WARNING
Important Charging Notes
CHEMICAL/EXPLOSION
HAZARD Read ALL
instructions before charging
or using battery. Failure to
follow ALL instructions may
result in fire, severe burns, or release of
toxic materials.
Battery Disposal: The EPA certified RBRCQ®
Battery Recycling Seal on the nickel-cadium
(Ni-Cd) battery indicates Ramset is voluntarily
participating in an industry program to collect
and recycle these batteries at the end of
their useful life, when taken out of service in
the United States or Canada. The RBRCQ®
program provides a convenient alternative
to placing used Ni-Cd batteries into the
trash or the municipal waste stream, which
may be illegal in your area. Please call
1-800-8-BATTERY™ (1-800-822-8837) for
information on Ni-Cd battery recycling and
disposal in your area. Ramset’s involvement
in this program is part of our commitment to
preserving our environment and conserving
our natural resources.
CHARGING INSTRUCTIONS
1. Connect the round plug of the wall
mount unit to the front of the charger
base and plug the wall mount unit into
any 120V AC outlet. A LED by the plug
indicates the base unit has power.
2. Set the charger base on a stable surface
and insert the battery or batteries, contact
first, into the opening of the charger
base.
3. The TrakFast charger incorporates a
charge level indicator to inform the user
of the battery charge level.
A red light will illuminate at all times
during a charge cycle.
One green light
= battery at 50% capacity
Two green lights
= battery at 75% capacity
Three green lights
= battery at FULL capacity
The red light will not be lit when the
battery is at full charge.
CHARGING DONT’S
• Do not charge battery when
temperature is below 40°F (5°C).
• Do not drop battery or charger.
• Do not allow metal objects to come
in contact with battery terminals.
• Do not puncture or attempt to open
battery case or cells.
• Do not store battery where it will
be subjected to temperatures
above 120°F (49°C).
• Do not incinerate battery.
• Do not use a defective battery
charger, one that overheats
and/or smokes when plugged in.
THE BATTERY AND CHARGING SYSTEM
7
THE BATTERY AND CHARGING SYSTEM
RECHARGEABLE
NICKEL-CADMIUM
BATTERY
Battery
Charger Base
Ramset Cordless Charging System
Wall Mount Unit
THE BATTERY AND CHARGING SYSTEM
THE BATTERY AND CHARGING SYSTEM
8
INSERTING BATTERY
1. Load the Battery, contacts first, into the
TrakFast tool.
2. Lock Battery into place with Battery Clip.
BATTERY INDICATOR LIGHT
The illustration is a closeup of the side of the
TrakFast tool. On the side of the Handle is a
small plastic lens. This is the Battery Voltage
Indicator Light
To check the battery voltage, the LED on the
right should be flashing or blinking green.
Pushing down on the Work Contact Element
will turn on Fan Motor and LED will be a
solid green. If the LED blinks or glows red,
recharge the Battery.
FUEL CELL AND METERING VALVE
9
FUEL CELL AND METERING VALVE
Fuel Cell
DANGER
EXPLOSION/FIRE HAZARD
Read ALL safety instructions
before using or
handling the fuel cell. Failure
to follow ALL instructions
may result in explosion or
fire. This may cause severe
personal injuries or property
damage.
Keep the fuel cell away
from heat, sparks and
open flame.
Exposure to temperatures
above 120°F (49°C) may
cause the fuel cell to burst,
releasing flammable gas.
WARNING
• Sunlight can raise the inside
temperature of an unventilated
car or van to above 140°F (60°C).
• Do not puncture or attempt to
open the fuel cell; it is non-refillable.
• Do not incinerate, reclaim or recycle
the fuel cell.
• Do not smoke while installing or
removing the metering cell.
• Do not inhale the spray.
• Keep out of the reach of children.
• Store fuel cell(s) in well-ventilated
areas only.
• Do not reuse metering valve.
There is a second container inside the fuel
cell. The inner container holds the fuel. The
space between the inner container and the
outer cylinder is filled with a gas, called the
propellant, which is under pressure.
To eject the fuel, propellant pressure squeezes
the inner fuel container, much as you squeeze
a tube of toothpaste. This squeezing action
ensures that all the fuel is used, and that the
TrakFast tool can operate in any position.
Because of this container-within-a-container
design, you might hear the sound of fluid
when shaking the fuel cell after all the fuel
has been used. This is the propellant, which
remains between the containers even after
all the fuel has been expelled.
If you expose the empty fuel cell to extreme
temperatures, the propellant gas will expand
and could cause the container to burst,
releasing flammable gases.
Metering Valve
The metering valve contains a fuel metering
system to inject the correct amount of fuel
into the combustion chamber.
The red metering valve is the only valve that
will operate properly with the TrakFast tool.
NOTE:
1. Do not attempt to reuse the metering
valve! Replace with fresh fuel cell/valve,
and dispose of spent cell/valve properly.
2. When replacing fuel cell also clean or
replace air filter for optimum tool operation.
Attaching Metering Valve to
Fuel Cell
To attach the metering valve to a fuel cell:
1. Press downward on the front side of the
valve (stem side) until it seats.
2. Press downward on the rear of the valve
unit it seats.
3.
The valve is now completely seated on the
fuel can and can be inserted into the tool.
FUEL CELL AND METERING VALVE
FUEL CELL AND METERING VALVE
10
INSERTING FUEL CELL
With the Metering Valve Stem pointed
toward the front of the tool, insert the
Metering Valve/Fuel Cell Assembly.
As you slide the Metering Valve/Fuel Cell
Assembly into the TrakFast tool, you will
notice that there is a Red Adaptor at the top
of the Cylinder Pocket. As is shown in the
illustration, this Adaptor is designed to ensure
that the Metering Valve Stem is properly
aligned with the small hole, or orifice that
leads to the Combustion Chamber. Insert
the Metering Valve Stem into the orifice of
the red colored Adaptor.
You complete the loading of Fuel in the
TrakFast tool by closing the Actuator Cover.
You do this by swinging it up and over the
Fuel Valve/Cylinder Assembly and pushing
down until the Actuator Cover snaps into
position.
OUTDOOR WEATHER AND
THE TRAKFAST TOOL
Use the TrakFast tool outdoors, in clear
weather, when the Tool, Fuel Cell, and
Battery are between 20°F (-7°C) and 120°F
(49°C). Colder temperatures may damage
the TrakFast Tool and Battery Cell. Hotter
temperatures may damage the Tool and
Fuel Cell. Fuel should be stored out of direct
sunlight in surroundings less than 120°F
(49°C). After extended periods of continuous
use, cool the Tool by running the Fan Motor.
Operation when the Tool is less than 20°F
(-7°C) may damage the tool. Fuel Cells
at cold temperatures lose the required
propellant force. Bring the Tool, Battery Cell,
and Fuel Cell above minimum operating
temperature without direct exposure to
flame, and check the Battery.
CAUTION
The TrakFast tool should not be used in
the rain or where excessive moisture is
present. These conditions may result in
damage to
tool components and cause
tool to malfunction.
FASTENERS
The TrakFast tool can drive only Ramset
fasteners which have been collated into
strips. Any other fastener will cause tool
damage and void your warranty.
LOADING FASTENERS
The illustration below shows how to properly
load fasteners into the TrakFast tool.
1.
Pull the carrier assembly back until it locks.
2. Load four fastener strips into the rear slot
of the magazine.
3. Pull the carrier assembly slightly back,
push the follower button in, and gently
release the assembly to engage the
fasteners.
The Trigger on the TrakFast tool is automatically
locked and will not operate when there is
less than 2 fasteners in the feed magazine
and unless the work contact element is fully
depressed. The purpose of this feature is to
prevent needless blank cycling, which could
damage tool components.
DANGER
Two (2) fasteners will be left in the Magazine
after strips have been used. At this point
you can reload. It does not indicate that the
tool is empty. Because of a lockout feature
in the TrakFast tool, it will not operate when
the fastener supply in the tool is less than
two (2) fasteners.
TRAKFAST TOOL OPERATION
Press Work Contacting Element Against
Work Surface
Fan Motor will
turn on.
LED will be
steady green.
Fuel is injected
into Combustion
Chamber and
mixed with air by
the Fan.
Squeeze
the Trigger
The Spark Plug
sparks and fuel/
air mixture ignites.
Combustion
powers the Piston
Assembly driving
fastener.
Release Trigger—Lift the Tool
The Combustion Chamber opens.
Fan exhausts hot gases and cools internal
components.
NOTE: if no additional cycles are made, fan
will run for 7 seconds and then shut off.
WARNING
The Work Contacting Element and nose
may become hot after prolonged or rapid
use.
PREPARING AND USE OF TRAKFAST TOOL
PREPARING AND USE OF TRAKFAST TOOL
11
SERVICING
SERVICING
12
Field service should be restricted to
the following:
qCHECKING THE ENERGY LEVEL
OF THE BATTERY
qRECHARGING THE BATTERY
qCHECKING THE FUEL CELL AND
METERING VALVE
qREPLACING THE FUEL CELL
qCLEANING THE AIR FILTERS
qCLEARING A JAM
Attempts to go beyond these procedures
could result in serious personal injury or
damage to the TrakFast tool and voiding
of the warranty.
There are certain problems that you may
encounter when you are using the TrakFast
tool that you will be able to correct on the
work site, The following field service procedures are the only service procedures
you should attempt. Anything else that may
appear wrong with the TrakFast tool should
only be diagnosed and repaired by a fully
trained service technician. If you have any
reason to believe that your problem is beyond
the service procedures in this manual, contact
your Sales Representative immediately,
DANGER
Never attempt any maintenance of the
TrakFast tool without first removing the Fuel
Cell. Maintenance should only be started
after the tool is completely inoperative.
BATTERY CELL CHECK
Periodically check on the LED Battery
Voltage Indicator Light—the LED in
the Handle of the TrakFast tool. When
encountering a problem, the first step
should always be to make sure the Battery
has enough energy to operate the tool.
If the light is red, recharge the Battery, If
the light is glowing green, indicating that the
Battery is charged, check the ignition system.
FUEL CELL CHECK
Another typical service condition will occur
when the Fuel Cell becomes empty. A typical
symptom will be when the TrakFast tool’s
Fan operates and the LED is green, but the
tool does not drive fasteners completely. In
this case, take the Fuel Cell out of the tool,
check to see if the Cell still contains fuel
and that the Metering Valve is working. To
determine if there is any fuel left in the Fuel
Cell simply place the Metering Stem against
a solid object, and gently push about three
or four times. A small amount of fuel should
be released each time. Never perform this
test near an open flame or sparks, while
smoking, or where the fuel may get into
your eyes. If fuel is not released with each
operation of the Metering Valve, this indicates
that there is no more fuel left in the cylinder
and it must be replaced. Dispose of the
empty Fuel Cell properly.
AIR FILTER
Open the cover by pressing slightly above
the Red Adapter, and pivoting the cover
open. The Air Filter simply lift out. Tap the
filter GENTLY to remove any dust. You
should check and clean the Air Filter every
two days.
CLEARING A JAM
A typical problem you may encounter is
having a jammed fastener. Because of the
unique design of the TrakFast tool, clearing
a jammed fastener is easy.
1. Pull the Carrier Assembly back until it
locks.
2. Loosen the Magazine Locking Knob
three full turns.
3. Remove the
Magazine by
sliding it away
from the nose
of the tool.
SERVICING
13
SERVICING
CLEARING A JAM (continued)
At this point, the jammed fastener should fall
out. If the jammed fastener does not fall out,
carefully remove the fastener taking care not
to damage the Shear Block.
After you have removed the jammed fastener
take the following steps to reattach the
Magazine to the tool:
1. Use the two guide pins to align the
Magazine at the nose of the tool.
2. Position the Magazine mounting slot
over the locking knob screw.
3. Slide the Magazine firmly against
the nose.
4. Tighten the Magazine Locking Knob
and reload the tool.
DANGER
Make sure Magazine is all the way forward
against the nose and Magazine Locking
Knob is tightened securely before operating
tool. Attempting to use tool with a loose
Magazine may result in loss of fastener
control, damage to tool, or pin discharge
toward tool operator.
If you find that the TrakFast tool’s Fan does
not operate after clearing a jam:
Check the condition of your Battery Cell.
If the Handle LED indicator emits a constant
red glow when depressing the tool, recharge
the Battery.
END-OF-WORKDAY ROUTINE
At the end of each workday, conduct an
end-of-workday routine. These simple steps
are based on maintaining the safety and
operational efficiency of the TrakFast tool.
Before you leave the worksite:
1. Remove the Battery and store in the tool
case. Always use the TrakFast tool case
for transporting and storing the tool.
2.
Dispose of all empty Fuel Cells. Remember
to dispose of these cells where they
will not be found by children, crushed,
punctured, or burned.
3. Place the Battery Cell in its Charger only
if it needs charging as indicated by the
red charge light in the handle.
4. Wipe your TrakFast tool with a clean,
soft cloth.
5. Check Work Contacting Element to
ensure it is operating freely.
These simple steps will not only ensure that
your TrakFast tool is ready to go to work the
next day, but will also ensure that you get
the maximum efficiency from your tool.
TRAKFAST TOOL ACCESSORIES
A variety of accessories are available for the
TrakFast tool:
• BatteryCells
• ClearSafetyGlasses
• TrakFastToolCharger
Contact your Ramset Distributor Sales
Representative for additional information.
act your Sales Representative immediately.
TROUBLESHOOTING
14
TROUBLESHOOTIN G
SYMPTOM POSSIBLE PROBLEMS SERVICE
Preparing Tool for Operation—Battery/Charger Problems
Normal Stage of Operation
— Battery Cell does
not appear to accept
charge. Green charger
light does not come on.
— Flashing lights on char-
ger base unit.
— Fan does not run—tool
LED is off.
— Fan does not run,
or runs slower than
normal—tool LED is red.
— Fan runs intermittently.
— Inoperative indicator
lights on charger.
— Battery Cell damaged
or cycle life exhausted.
— Damaged charger.
— Damaged Battery Cell
— Battery Completely
Drained
— Battery Cell is not
charged.
— Magazine is loose,
preventing current
flow from Magazine
to Handle and
Cylinder Head.
— Magazine contacts
at top of Magazine,
or contact posts in
base of Handle, are
oily, dirty, or corroded.
— Battery Terminals or
Magazine battery
contacts are oily,
dirty, or corroded.
— Battery Cell is
discharged.
— Magazine is loose or
contacts are bent.
— Try Battery Cell in tool after 3 hours on
charge cycle. If tool LED is green, charger
lights are not working properly. Replace
charger, monitor charging time to ensure
Battery Cell has adequate time for recharging.
It’s normal for Battery to feel warm after
properly charging.
— Replace Battery Cell.
— Discontinue use immediately and unplug
from power source. Replace charger and tag
or dispose of charger to prevent accidental
reuse or connection to power source.
— Replace Battery
— Allow Battery to Charge for 5 minutes
— Charge Battery Cell according to Operating
Manual.
— Make sure Magazine is tight to nose of tool,
and secure with magazine Locking Knob.
— Clean contacts as required.
— Clean Battery Cell terminals. Clean
Magazine Battery Cell contacts as required.
— Charge Battery Cell.
— Tighten Magazine, or bend contacts up.
TROUBLESHOOTING
TROUBLESHOOTING
15
SYMPTOM POSSIBLE PROBLEMS SERVICE
Pre-Combustion/Combustion Stage of Operation
Power/Exhaust Stage of Operation
— Work Contacting
Element does not
depress fully—tool
does not operate.
— Tool will not cycle-fan
runs, LED is green.
— Tool operates properly,
but fasteners do not
drive fully.
— Tool operates, but no
fastener is driven.
— Tool operates erratically
or appears to be
losing power—tool
LED is green.
— Lockout Bracket is stuck
in lockout position.
— Work Contacting
Element is bent, or
build-up of debris in
track restricts operation.
— Follower is not behind
strip.
— Fan motor O-Ring
pinched.
— Fuel Cell is empty.
— Spark Wire out of spark
plug.
— Spark does not occur.
— Battery cell is
discharged.
— Fuel Cell is low.
— There may be loss of
seal in combustion
chamber.
— Fastener strip may be
binding.
— Follower not properly
engaged behind fastener.
— Jammed fastener.
— Fuel Cell is low.
— Spark Plug wire is
loose.
— Filter element is dirty,
causing tool to overheat.
— Tool Sleeve or O-Rings
are dirty.
— Check Negator Cover screw for excessive
tightness. Remove cover if necessary and
clean out build-up of debris from track.
— Remove and inspect Lower Probe. Clean
track with cloth. Repair or replace Lower
Probe as required.
— Put follower behind strip.
— Contact Authorized Ramset Distributor
Sales Representative for service.
— Replace Fuel Cell.
— Contact Authorized Ramset Distributor
Sales Representative for service.
— Contact Authorized Ramset Distributor
Sales Representative for service.
— Charge Battery Cell.
— Check Fuel Cell according to Operating
Manual and replace as required.
— Press Work Contact Element against work-
piece for one minute. Pull trigger. If fastener
does not drive, there is a leak that requires
service.
— Use only fasteners meeting Ramset
specifications.
— Locate follower behind fastener strip and
engage strip according to instructions in
Operating Manual.
— Clear jam according to Operating Manual.
— Check Fuel Cell according to Operating
Manual.
— Contact Ramset Distributor Sales
Representative for Service.
— Remove Filter element and clean according
to Operating Manual. Use safe cleaning
solution to remove stubborn debris.
— Clean tool per Cleaning Procedure.
TROUBLESHOOTING
16
TROUBLESHOOTING
SYMPTOM POSSIBLE PROBLEMS SERVICE
Returning/Purging Stage of Operation
If the TrakFast tool will not operate after following the above service directions,
return the tool to an Ramset Distributor Sales Representative for service.
800-241-5640
www.ramset.com
— Tool operated and
drove fastener, but
piston did not return
to up position.
— Combustion Chamber
does not drop after tool
cycles.
— Built-up dirt and debris
on Piston or in Nose
bore.
— Mushrooming of
Piston Tip.
— Exhaust ports on the
Sleeve are dirty or
clogged.
— Tool (Sleeve) or
O-Rings are dirty.
— Work Contacting
Element is bent,
or tool is dirty.
— Clean Piston and Nose bore with safety
solvent.
— Contact Ramset Distributor Sales
Representative for service.
— Return tool to Authorized Ramset Distributor
Sales Representative for service.
— Clean tool per Cleaning Procedure.
— Clean tool or replace Work Contacting
Element as required.
Ramset warrants that new TrakFast
systems power fastening tools, parts
and accessories will be free from defects
in material and workmanship for the
period shown below.
TWO-YEAR/50,000 SHOT WARRANTY
A two-year/50,000 shot warranty, which
ever comes first, will apply to all parts,
except those listed below as normal
wearing parts, or parts which are
specifically covered by an extended
warranty.
SIX-MONTH/10,000 SHOT WARRANTY
A six-month/10,000 shot warranty applies
to the following parts, which are considered
normal wearing parts:
• Bumper
• Piston Assembly
• O-Rings
• Piston Rings
The warranty period is based off of tool
build date, determined from the tool serial
number. Ramset may extend the warranty
time frame from the date of purchase with
a qualifying document proving date of
purchase.
WARRANTY STATEMENT
Ramset’s sole liability hereunder will
be to replace any part or accessory
which proves to be defective within the
specific time period. Any replacement
part
or accessory provided in accordance
with
this warranty will carry a warranty for the
balance of the period of warranty applicable
to the part it replaces. This warranty does
not apply to part replacement required due
to normal wear.
This warranty is void as to any tool which
has been subjected to misuse, abuse,
accidental or intentional damage, use with
fasteners, fuel, battery, or battery chargers
not meeting Ramset specification, size, or
quality, improperly maintained, repaired
with other than genuine TrakFast replacement parts, damaged in transit or handling,
or which,
in Ramset’s opinion, has been
altered or repaired in a way that affects or
detracts
from the performance of the tool.
Ramset MAKES NO WARRANTY,
EXPRESSED OR IMPLIED, RELATING
TO MERCHANTABILITY, FITNESS, OR
OTHERWISE, EXCEPT AS STATED ABOVE
and the liability AS STATED ABOVE AND
AS ASSUMED ABOVE is in lieu of all other
warranties arising out of, or in connection
with, the use and performance of the tool,
except to the extent otherwise provided
by applicable law.
Ramset SHALL IN NO EVENT BE
LIABLE FOR ANY
DIRECT, INDIRECT, OR
CONSEQUENTIAL DAMAGES, INCLUDING,
BUT NOT LIMITED
TO DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED
PROFITS OR
PRODUCTION, SPOILAGE
OF MATERIALS,
INCREASED COST OF
OPERATION OR OTHERWISE.
Ramset reserves the right to change
specifications, equipment, or designs
at any time without notice and without
incurring obligation.
WARRANTY
WARRANTY
17
RAMSET GAS TOOL SYSTEMS WARRANTY AND LIMITATIONS
FOR TOOL REPAIR SERVICE CONTACT YOUR LOCAL
AUTHORIZED RAMSET DISTRIBUTOR OR TO FIND
YOUR NEAREST RAMSET TOOL REPAIR CENTER
VISIT OUR WEB SITE AT WWW.RAMSET.COM
OR CALL 800-241-5640
Concrete Fastening Systems
Glendale Heights, IL 60139
800-RAMSET6 (1-800-726-7386)
www.ramset.com
Buy with Confidence...
Buy From Your Authorized Distributor
AN ILLINOIS TOOL WORKS COMPANY
© ILLINOIS TOOL WORKS 2010
PRINTED IN THE U.S.A. Form No. 7505152-09/10
Loading...