RAM Mount VB-131R4-SW1 User Manual
Item Number
RAM-VB-131R4
Vehicle base for the
GMC SIERRA (DELUXE POWER SEATS)
(2000-2006)
GMC YUKON (DELUXE POWER SEATS)
(2000-2006)
CHEVY SILVERADO (DELUXE POWER SEATS)
(1999-2006)
CHEVY SUBURBAN (DELUXE POWER SEATS)
(2000-2006)
SPECIFICATIONS
Placement
Passenger side, in front, where seat frame meets
floor board.
Drilling Required
None - uses existing seat bolts
Seat Configuration
Bucket
RAM No-Drill TM Seat Bases
National Products, Inc.
CHEVROLET 2500 & 3500 C/K SERIES TRUCK (DELUXE
POWER SEATS) (2000-2006)
CHEVROLET AVALANCHE (2000-2006)
HUMMER H2 (2005-2006)
CADILLAC ESCALADE (2000-2006)
Construction/Finish
Steel/Black Powdercoat
Pole or Pedestal
Ordered Separately
Riser
Included
Weight 7.7 lbs.
Dimensions
Hole Center = 15”
Features
Installs in minutes with no drilling required
Won’t interfere with levers, factory-installed console, or 4WD lever
Misc.
Rock solid construction
Lifetime warranty
National Products, Inc.
Phone: 206-763-8361
Fax: 206-763-9615
Address: 1205 S Orr St
Seattle, WA 98108
Website: www.ram-mount.com
Email: staff@ram-mount.com
Shown In Use
RAM-VB-131R4
This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
Item Number
RAM-VB-131R4
RAM No-Drill TM Seat Bases
National Products, Inc.
Vehicle base for the
GMC SIERRA (DELUXE POWER SEATS)
(2000-2006)
GMC YUKON (DELUXE POWER SEATS)
(2000-2006)
CHEVY SILVERADO (DELUXE POWER SEATS)
(1999-2006)
CHEVY SUBURBAN (DELUXE POWER SEATS)
(2000-2006)
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Note that attaching the riser prior to installing the base into the vehicle is suggested.
1. Move the passenger side seat to its rear most position.
2. Locate the two front seat frame nuts holding the passenger side seat to the floor board. The one closest to the
passenger side door will be located within the seat track. The nut closest to the center of the vehicle may be under a
piece of plastic trim but is located outside of the seat track toward the inside of the seat frame. Both have a star shape
but can be loosened using a 15MM socket wrench.
3. Loosen the two nuts holding the front of the passenger side seat down. Only do so enough to pass the no drill base
in between the seat tracks and floor board.
4. Once there is enough room for the base, slide the base under the seat so that the notches align with the seat studs
projecting upward from the floor board. Make sure the back of each slos engages the seat studs.
5. Using the socket wrench, fully tighten the seat frame nuts to secure the base in place.
CHEVROLET 2500 & 3500 C/K SERIES TRUCK (DELUXE
POWER SEATS) (2000-2006)
CHEVROLET AVALANCHE (2000-2006)
HUMMER H2 (2005-2006)
CADILLAC ESCALADE (2000-2006)
National Products, Inc.
Phone: 206-763-8361
Fax: 206-763-9615
Address: 1205 S Orr St
Seattle, WA 98108
Website: www.ram-mount.com
Email: staff@ram-mount.com
This document, including images, may not be reproduced partly or fully without the expressed written consent of National Products, Inc.
Loading...