RAM Mount 234-HUB1U User Manual

RAM TOUGH-HUB INSTRUCTIONS

Parts Index

A . RAM TOUGH-HUB (QTY. 1)
B. BARE WIRE POWER CABLE (QTY. 1)
C. IGNITION TRIGGER WIRE (QTY. 1)
D. USB CABLE (QTY. 1)
E. USB PORT FRAME (QTY. 1)
F. FOAM STRIP FOR USB FRAME (QTY. 1)
G. 1/4” SCREW FOR USB FRAME (QTY. 2, + 2 EXTRA)

-5 QTY. USB PORTS

-ADDITIONAL USB PORT

-RJ 45 ETHERNET PORT

-12-48 VOLT DC INPUT

1. USE (F) FOAM STRIP TO ADHERE UNDER (E) USB
PORT FRAME.

2. POSITION (E) USB PORT FRAME IN FRONT
OF THE 5 USB PORTS.

3. SECURE TO HUB USING (G) SCREWS.

ONLY RECOMMENDED FOR USB PORTS THAT DO NOT

FREQUENTLY CONNECT AND DISCONNECT

A

TO CHANGE DEFAULT PRE SET, REMOVE HOUSING AND
SWITCH THE SMALL JUMPER COMPONENT FROM “POS 2”
TO ANY OF THE OTHER 3 POSITIONS:

POS 0
POS 1
POS 2
POS 3

BLUE LED LIGHT BLINKS DURING TIME DELAY

B

IGNITION TRIGGER CAN BE WIRED TO THE IGNITION
OF THE VEHICLE (OR OTHER 12V IGNITION SOURCE)
TO PROVIDE A TIMED DISCONNECT TO THE
CONNECTED PERIPHERALS AFTER VEHICLE HAS
BEEN TURNED OFF. WHEN VEHICLE IGNITION IS OFF,

-IGNITION TRIGGER

-USB OUTPUT PORT

- CONSTANT ON, IGNITION TRIGGER HAS NO EFFECT

- TIME DELAY FOR 5 MINUTES

- TIME DELAY FOR 15 MINUTES

- TIME DELAY FOR 45 MINUTES

TOUGH-HUB CONTINUES TO PROVIDE POWER TO THE
CONNECTED PERIPHERALS FOR A PRE SET
DURATION OF TIME. THE DEFAULT DELAY IS PRE SET
FROM THE FACTORY TO 15 MINUTES.

C

E

G

F

COMPLETE ASSEMBLY

RMR-INS-234-HUB1

D

RAM TOUGH-HUB INSTRUCTIONS

Parts Index

A . RAM TOUGH-HUB (QTY. 1)
B. BARE WIRE POWER CABLE (QTY. 1)
C. IGNITION TRIGGER WIRE (QTY. 1)
D. USB CABLE (QTY. 1)
E. USB PORT FRAME (QTY. 1)
F. FOAM STRIP FOR USB FRAME (QTY. 1)

G. 1/4” SCREW FOR USB FRAME (QTY. 2, + 2 EXTRA)

-5 QTY. USB PORTS

-ADDITIONAL USB PORT

-RJ 45 ETHERNET PORT

-12-48 VOLT DC INPUT

A

TO CHANGE DEFAULT PRE SET, REMOVE HOUSING AND
SWITCH THE SMALL JUMPER COMPONENT FROM “POS 2”
TO ANY OF THE OTHER 3 POSITIONS:

POS 0
POS 1
POS 2
POS 3

BLUE LED LIGHT BLINKS DURING TIME DELAY

B

-IGNITION TRIGGER

-USB OUTPUT PORT

CONSTANT ON

-

- TIME DELAY FOR 5 MINUTES

- TIME DELAY FOR 15 MINUTES

- TIME DELAY FOR 45 MINUTES

C

E

G

D

F

IGNITION TRIGGER CAN BE WIRED TO THE IGNITION
OF THE VEHICLE (OR OTHER 12V IGNITION SOURCE)
TO PROVIDE A TIMED DISCONNECT TO THE
CONNECTED PERIPHERALS AFTER VEHICLE HAS
BEEN TURNED OFF. WHEN VEHICLE IGNITION IS OFF,
TOUGH-HUB CONTINUES TO PROVIDE POWER TO THE
CONNECTED PERIPHERALS FOR A PRE SET
DURATION OF TIME. THE DEFAULT DELAY IS PRE SET
FROM THE FACTORY TO 15 MINUTES.

COMPLETE ASSEMBLY

1. USE (F) FOAM STRIP TO ADHERE UNDER (E) USB
PORT FRAME.

2. POSITION (E) USB PORT FRAME IN FRONT
OF THE 5 USB PORTS.

3. SECURE TO HUB USING (G) SCREWS.

ONLY RECOMMENDED FOR USB PORTS THAT DO NOT

FREQUENTLY CONNECT AND DISCONNECT

RMR-INS-234-HUB1