RAM QUICK DRAW Assembly Instructions Manual
RAM® QUICK DRAW™ ASSEMBLY INSTRUCTIONS (SIDE A)
PARTS INDEX:
A. RAM® QUICK DRAW™ (QTY. 1)
B. DOCKING CUP (QTY. 1)
C. TOP CUP (QTY. 1)
D. #6-32 X ½” MACHINE SCREW (QTY. 8)
E. #6-32 NYLOCK NUT (QTY. 8)
A
B
C
D
B
E
SUGGESTED TOOLS:
5/6” HEX WRENCH
#2 PHILIPS HEAD SCREWDRIVER
STEP 1 - ATTACH TOP CUP
ATTACH (C) TOP CUP TO (A) QUICK DRAW™ USING 4 (D) SCREWS AND 4 (E) NUTS SO
THAT OPENING OF TOP CUP FACES THE LENGTH OF THE QUICK DRAW AS SHOWN.
SCREWS SHOULD BE INSERTED UPWARD TOWARDS (C) TOP CUP.
STEP 2 - ATTACH DOCKING CUP
ATTACH (B) DOCKING CUP TO (A) QUICK DRAW™ USING 4 (D) SCREWS AND 4 (E) NUTS SO
THAT DEVICE EXTENDS THE (C) TOP CUP ½” TO 1” WHILE DOCKED (SEE TENSION
ADJUSTMENT). SCREWS SHOULD BE INSERTED DOWNWARD TOWARDS QUICK DRAW SPINE.
TENSION ADJUSTMENT
THE PLACEMENT OF THE (B) DOCKING CUP CAN BE ADJUSTED TO FIT VARIOUS ACCESSORIES. SLOTTED HOLES ALONG (A) QUICK DRAW™ SPINE ALLOW SCREWS
AND NUTS TO BE ATTACHED TO ADJUST FOR VARIOUS HEIGHTS. THE GOAL IS TO PROVIDE SPRING TENSION, BASED ON THE OVERALL LENGTH OF THE DEVICE,
INCLUDING ATTACHED ACCESSORIES. IT IS IMPORTANT TO ADJUST DOCK SO THAT DEVICE HAS ADEQUATE SPRING TENSION TO FORCE (C) TOP CUP AND DEVICE
DOWN ONTO THE (B) DOCKING CUP. THIS IS CRITICAL FOR PROPER FUNCTIONALITY. DEVICE SHOULD NOT SHAKE OR RATTLE WHILE DOCKED.
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
TENSION ADJUSTMENT
DOCKING CUP AND TOP CUP MAY
VARY BASED ON HAND-HELD DEVICE.
STEP 1
STEP 2
RMR-INS-QDJRBS
RAM® QUICK DRAW™ ASSEMBLY INSTRUCTIONS (SIDE A)
PARTS INDEX:
A. RAM® QUICK DRAW™ (QTY. 1)
B. DOCKING CUP (QTY. 1)
C. TOP CUP (QTY. 1)
D. #6-32 X ½” MACHINE SCREW (QTY. 8)
E. #6-32 NYLOCK NUT (QTY. 8)
SUGGESTED TOOLS:
5/6” HEX WRENCH
#2 PHILIPS HEAD SCREWDRIVER
STEP 1 - ATTACH TOP CUP
ATTACH (C) TOP CUP TO (A) QUICK DRAW™ USING 4 (D) SCREWS AND 4 (E) NUTS SO
THAT OPENING OF TOP CUP FACES THE LENGTH OF THE QUICK DRAW AS SHOWN.
SCREWS SHOULD BE INSERTED UPWARD TOWARDS (C) TOP CUP.
STEP 2 - ATTACH DOCKING CUP
ATTACH (B) DOCKING CUP TO (A) QUICK DRAW™ USING 4 (D) SCREWS AND 4 (E) NUTS SO
THAT DEVICE EXTENDS THE (C) TOP CUP ½” TO 1” WHILE DOCKED (SEE TENSION
ADJUSTMENT). SCREWS SHOULD BE INSERTED DOWNWARD TOWARDS QUICK DRAW SPINE.
TENSION ADJUSTMENT
THE PLACEMENT OF THE (B) DOCKING CUP CAN BE ADJUSTED TO FIT VARIOUS ACCESSORIES. SLOTTED HOLES ALONG (A) QUICK DRAW™ SPINE ALLOW SCREWS
AND NUTS TO BE ATTACHED TO ADJUST FOR VARIOUS HEIGHTS. THE GOAL IS TO PROVIDE SPRING TENSION, BASED ON THE OVERALL LENGTH OF THE DEVICE,
INCLUDING ATTACHED ACCESSORIES. IT IS IMPORTANT TO ADJUST DOCK SO THAT DEVICE HAS ADEQUATE SPRING TENSION TO FORCE (C) TOP CUP AND DEVICE
DOWN ONTO THE (B) DOCKING CUP. THIS IS CRITICAL FOR PROPER FUNCTIONALITY. DEVICE SHOULD NOT SHAKE OR RATTLE WHILE DOCKED.
A
C
B
DOCKING CUP AND TOP CUP MAY
VARY BASED ON HAND-HELD DEVICE.
STEP 1
D
B
E
STEP 2
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
TENSION ADJUSTMENT
RMR-INS-QDJRBS
RAM® QUICK DRAW™ ASSEMBLY INSTRUCTIONS (SIDE B)
ATTACHING WIRE CLIP
REMOVE SCREW ABOVE USB PORT, SNAP POWER CORD IN WIRE CLIP, AND RE-INSERT SCREW TO SECURE POWER CORD THROUGH WIRE CLIP.
AVOID SHARP BENDS
WARNING: THIS PRODUCT IS DESIGNED TO BE MOUNTED WITH A GENUINE RAM® MOUNT. IT IS THE RESPONSIBILITY OF THE
INSTALLER/END USER TO ENSURE THIS PRODUCT IS PROPERLY MOUNTED AND SECURED, AS TO AVOID FREE MOVEMENT ABOUT THE
CAB OF THE VEHICLE OR SIMILAR INSTALLATION ENVIRONMENT. PLEASE USE ALL CABLE RETENTION FEATURES SUPPLIED WITH THIS
PRODUCT, AND USE BEST PRACTICES IN WIRE ROUTING TO AVOID DAMAGE TO THE MOUNT OR MOUNTED DEVICE. NOT FOLLOWING
DOCKING INSTRUCTIONS
1. PLACE TOP END OF DEVICE INTO (C)
TOP CUP. ENGAGE SPRING TENSION
BY APPLYING UPWARD FORCE.
THESE INSTRUCTIONS MAY VOID YOUR WARRANTY.
2. ONCE UPWARD FORCE IS APPLIED, THERE SHOULD BE
AMPLE ROOM TO FIT ENTIRE DEVICE INTO DOCKING STATION
WITHOUT MAKING CONTACT WITH (B) DOCKING CUP. ALIGN
BOTTOM OF DEVICE WITH GROOVES IN (B) DOCKING CUP.
3. ONCE ALIGNED, ALLOW SPRING
TENSION TO ENGAGE YOUR DEVICE
WITH DOCKING CONNECTOR PINS
ON (B) DOCKING CUP.
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
1
2
3
RMR-INS-QDJRBS
RAM® QUICK DRAW™ ASSEMBLY INSTRUCTIONS (SIDE B)
ATTACHING WIRE CLIP
REMOVE SCREW ABOVE USB PORT, SNAP POWER CORD IN WIRE CLIP, AND RE-INSERT SCREW TO SECURE POWER CORD THROUGH WIRE CLIP.
AVOID SHARP BENDS
WARNING: THIS PRODUCT IS DESIGNED TO BE MOUNTED WITH A GENUINE RAM® MOUNT. IT IS THE RESPONSIBILITY OF THE
INSTALLER/END USER TO ENSURE THIS PRODUCT IS PROPERLY MOUNTED AND SECURED, AS TO AVOID FREE MOVEMENT ABOUT THE
CAB OF THE VEHICLE OR SIMILAR INSTALLATION ENVIRONMENT. PLEASE USE ALL CABLE RETENTION FEATURES SUPPLIED WITH THIS
PRODUCT, AND USE BEST PRACTICES IN WIRE ROUTING TO AVOID DAMAGE TO THE MOUNT OR MOUNTED DEVICE. NOT FOLLOWING
DOCKING INSTRUCTIONS
1. PLACE TOP END OF DEVICE INTO (C)
TOP CUP. ENGAGE SPRING TENSION
BY APPLYING UPWARD FORCE.
THESE INSTRUCTIONS MAY VOID YOUR WARRANTY.
2. ONCE UPWARD FORCE IS APPLIED, THERE SHOULD BE
AMPLE ROOM TO FIT ENTIRE DEVICE INTO DOCKING STATION
WITHOUT MAKING CONTACT WITH (B) DOCKING CUP. ALIGN
BOTTOM OF DEVICE WITH GROOVES IN (B) DOCKING CUP.
3. ONCE ALIGNED, ALLOW SPRING
TENSION TO ENGAGE YOUR DEVICE
WITH DOCKING CONNECTOR PINS
ON (B) DOCKING CUP.
1
RAM Mounting Systems
8410 Dallas Ave S
Seattle, WA 98108
Phone: (206) 763-8361
Fax: (206) 763-9615
www.rammount.com
support@rammount.com
2
3
RMR-INS-QDJRBS
Loading...