RAM Chassis 3500 2016 Owner's Manual
2016
OWNER’S MANUAL
Chassis Cab
VEHICLES SOLD IN CANADA
With respect to any Vehicles Sold in Canada, the name FCA
US LLC shall be deemed to be deleted and the name FCA
Canada Inc. used in substitution therefore.
DRIVING AND ALCOHOL
Drunken driving is one of the most frequent causes of
accidents.
Your driving ability can be seriously impaired with blood
alcohol levels far below the legal minimum. If you are
drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
WARNING!
Driving after drinking can lead to an accident.
Your perceptions are less sharp, your reflexes are
slower, and your judgment is impaired when you
have been drinking. Never drink and then drive.
This manual illustrates and describes the operation of
features and equipment that are either standard or optional on this vehicle. This manual may also include a
description of features and equipment that are no longer
available or were not ordered on this vehicle. Please
disregard any features and equipment described in this
manual that are not on this vehicle.
FCA US LLC reserves the right to make changes in design
and specifications, and/or make additions to or improvements to its products without imposing any obligation
upon itself to install them on products previously manufactured.
Copyright © 2015 FCA US LLC
SECTION PAGE
INTRODUCTION . ..............................................................3
1
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ..................................9
2
UNDERSTANDING THE FEATURES OF YOUR VEHICLE .................................121
3
UNDERSTANDING YOUR INSTRUMENT PANEL ......................................227
4
STARTINGANDOPERATING ....................................................393
5
TABLE OF CONTENTS
1
2
3
4
5
WHATTODOINEMERGENCIES..................................................531
6
MAINTAININGYOURVEHICLE...................................................557
7
MAINTENANCE SCHEDULES ....................................................627
8
IF YOU NEED CONSUMER ASSISTANCE ............................................635
9
INDEX .....................................................................647
10
6
7
8
9
10
INTRODUCTION
CONTENTS
䡵 INTRODUCTION ........................4
1
䡵 VEHICLE IDENTIFICATION NUMBER ........6
䡵 HOW TO USE THIS MANUAL ..............4
䡵 WARNINGS AND CAUTIONS ..............6
䡵 VAN CONVERSIONS/CAMPERS ............6
䡵 VEHICLE MODIFICATIONS/ALTERATIONS ....7
4 INTRODUCTION
INTRODUCTION
Congratulations on selecting your new FCA US LLC
vehicle. Be assured that it represents precision workmanship, distinctive styling, and high quality - all essentials
that are traditional to our vehicles.
This Owner’s Manual has been prepared with the assistance of service and engineering specialists to acquaint
you with the operation and maintenance of your vehicle.
It is supplemented by Warranty Information, and various
customer-oriented documents. Please take the time to
read these publications carefully. Following the instructions and recommendations in this manual will help
assure safe and enjoyable operation of your vehicle.
If applicable, refer to the Diesel Supplement for diesel
related information.
NOTE: After reviewing the owner information, it
should be stored in the vehicle for convenient referencing and remain with the vehicle when sold.
When it comes to service, remember that your authorized
dealer knows your vehicle best, has factory-trained technicians and genuine MOPAR® parts, and cares about
your satisfaction.
RAM is a registered trademark of FCA US LLC.
HOW TO USE THIS MANUAL
Consult the Table of Contents to determine which section
contains the information you desire.
Since the specification of your vehicle depends on the
items of equipment ordered, certain descriptions and
illustrations may differ from your vehicle’s equipment.
The detailed index at the back of this Owner’s Manual
contains a complete listing of all subjects.
Consult the following table for a description of the
symbols that may be used on your vehicle or throughout
this Owner’s Manual:
INTRODUCTION 5
1
6 INTRODUCTION
WARNINGS AND CAUTIONS
This Owner’s Manual contains WARNINGS against
operating procedures that could result in a collision,
bodily injury and/or death. It also contains CAUTIONS
against procedures that could result in damage to your
vehicle. If you do not read this entire Owner’s Manual,
you may miss important information. Observe all Warnings and Cautions.
VAN CONVERSIONS/CAMPERS
The New Vehicle Limited Warranty does not apply to
body modifications or special equipment installed by van
conversion/camper manufacturers/body builders. Refer
to the Warranty Information book, Section 2.1.C. Such
equipment includes video monitors, VCRs, heaters,
stoves, refrigerators, etc. For warranty coverage and
service on these items, contact the applicable manufacturer.
Operating instructions for the special equipment installed by the conversion/camper manufacturer should
also be supplied with your vehicle. If these instructions
are missing, please contact your authorized dealer for
assistance in obtaining replacement documents from the
applicable manufacturer.
For information on the Body Builders Guide refer to:
www.rambodybuilder.com. This website contains dimensional and technical specifications for your vehicle. It
is intended for Second Stage Manufacturer’s technical
support. For service issues, contact your authorized
dealer.
VEHICLE IDENTIFICATION NUMBER
The Vehicle Identification Number (VIN) is found on the
left front corner of the instrument panel, visible through
the windshield. This number also appears on the vehicle
frame and underbody as well as the Automobile Information Disclosure Label affixed to a window on your
vehicle, the vehicle registration and title.
Vehicle Identification Number
NOTE: It is illegal to remove or alter the VIN.
INTRODUCTION 7
VEHICLE MODIFICATIONS/ALTERATIONS
1
WARNING!
Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and
may lead to a collision resulting in serious injury or
death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS
䡵 A WORD ABOUT YOUR KEYS .............12
▫ General Information ....................21
2
▫ Ignition Node Module (IGNM) ............12
▫ Keyless Push Button Ignition — If Equipped . . .13
▫ KeyFob.............................14
▫ Removing Key Fob From Ignition ..........17
▫ Key-In-Ignition Reminder ................19
▫ General Information ....................19
䡵 SENTRY KEY ..........................19
▫ Replacement RKE Key Fobs ..............21
▫ Customer RKE Key Fob Programming .......21
䡵 VEHICLE SECURITY ALARM ..............22
▫ Rearming Of The System .................22
▫ To Arm The System.....................22
▫ To Disarm The System ...................23
▫ Security System Manual Override ...........24
䡵 ILLUMINATED APPROACH ...............24
䡵 REMOTE KEYLESS ENTRY (RKE) ...........25
▫ Remote Unlock The Doors ...............26
▫ To Lock The Doors .....................28
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
▫ Sound Horn With Remote Key Lock .........28
▫ General Information ....................36
▫ Using The Panic Alarm ..................28
▫ Programming Additional RKE Key Fobs ......29
▫ Key Fob Battery Replacement .............29
▫ General Information ....................32
䡵 REMOTE STARTING SYSTEM — IF EQUIPPED .33
▫ How To Use Remote Start ................33
▫ Remote Start Abort Message ..............34
▫ To Enter Remote Start Mode...............34
▫ To Exit Remote Start Mode Without Driving The
Vehicle ..............................35
▫ To Exit Remote Start Mode And Drive The
Vehicle ..............................35
▫ Remote Start Comfort Systems — If Equipped . .36
䡵 DOOR LOCKS .........................37
▫ Manual Door Locks .....................37
▫ Power Door Locks — If Equipped ..........38
▫ Child-Protection Door Lock ...............40
䡵 KEYLESS ENTER-N-GO — PASSIVE ENTRY ....42
▫ General Information ....................45
䡵 WINDOWS ...........................46
▫ Power Windows — If Equipped ...........46
▫ Wind Buffeting .......................49
䡵 OCCUPANT RESTRAINT SYSTEMS ..........50
▫ Important Safety Precautions ..............50
▫ Seat Belt Systems ......................52
▫ Supplemental Restraint System (SRS) ........68
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
▫ Transporting Passengers .................116
▫ Child Restraints .......................83
▫ Transporting Pets .....................114
䡵 ENGINE BREAK-IN RECOMMENDATIONS . . .115
▫ Diesel Engine ........................115
䡵 SAFETY TIPS .........................116
▫ Exhaust Gas .........................117
▫ Safety Checks You Should Make Inside The
Vehicle .............................118
▫ Periodic Safety Checks You Should Make Outside
The Vehicle .........................120
2
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
A WORD ABOUT YOUR KEYS
Your vehicle uses either a key start ignition system or
keyless ignition system. The key start ignition system
consists of a either a bladed key with an immobilizer chip
in it, or a Key Fob with Remote Keyless Entry (RKE) Key
Fob and an Ignition Node Module (IGNM). The keyless
ignition system consists of a RKE Key Fob and a Keyless
Push Button Ignition.
Ignition Node Module (IGNM)
The Ignition Node Module (IGNM) operates similar to an
ignition switch. It has four operating positions, three with
detents and one that is spring-loaded. The detent positions are OFF, ACC, and ON/RUN. The START position
is a spring-loaded momentary contact position. When
released from the START position, the switch automatically returns to the ON/RUN position.
Ignition Module
1 — OFF
2 — ACC (ACCESSORY)
3 — ON/RUN
4 — START
Keyless Push Button Ignition — If Equipped
This feature allows the driver to operate the ignition
switch with the push of a button as long as the Remote
Keyless Entry (RKE) Key Fob is in the passenger compartment.
The Keyless Push Button Ignition has four operating
positions; three of which are labeled and will illuminate
when in position. The three positions are OFF, ACC, and
ON/RUN. The fourth position is START, during start
RUN will illuminate.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13
NOTE: In case the ignition switch does not change with
the push of a button, the RKE Key Fob may have a low or
dead battery. In this situation, a back up method can be
used to operate the ignition switch. Put the nose side
(side opposite of the emergency key) of the Key Fob
against the ENGINE START/STOP button, with your
foot applied on the brake pedal, and push to operate the
ignition switch.
2
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Keyless Push Button Ignition
1 — OFF
2 — ACC (ACCESSORY)
3 — ON/RUN
Key Fob
Key Fob — If Equipped
The Key Fob operates the ignition switch. Insert the
square end of the key fob into the ignition switch located
on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) Key
Fob and an emergency key, which stores in the rear of the
Key Fob.
The emergency key allows for entry into the vehicle
should the battery in the vehicle or the RKE Key Fob go
dead. You can keep the emergency key with you when
valet parking.
To remove the emergency key, slide the mechanical latch
at the top of the Key Fob sideways with your thumb and
then pull the key out with your other hand.
NOTE: When using the emergency key to gain access to
your vehicle, be aware that the security alarm may be
triggered. Insert the Key Fob into the ignition and place
the ignition in the ON/RUN mode to disarm the security
system.
Remote Keyless Entry (RKE) Key Fob (IGNM)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15
Keyless Push Button Ignition Key Fob — If Equipped
This Keyless Push Button Ignition Key Fob allows the
driver to operate the ignition switch with the push of a
button, as long as the Remote Keyless Entry (RKE) Key
Fob is in the passenger compartment. The Keyless Push
Button Ignition has four operating positions, three of
which are labeled and will illuminate when in position.
The three positions are OFF, ACC, and ON/RUN. The
fourth position is START, during start RUN will illuminate. It also contains the Remote Keyless Entry (RKE)
Key Fob and an emergency key, which stores in the rear
of the Key Fob.
The emergency key allows for entry into the vehicle
should the battery in the vehicle or the RKE Key Fob go
dead. You can keep the emergency key with you when
valet parking.
2
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
To remove the emergency key, slide the mechanical latch
on the backside of the Key Fob sideways with your
thumb and then pull the key out with your other hand.
NOTE: When using the emergency key to gain access to
your vehicle, be aware that the security alarm may be
triggered. Insert the Key Fob into the ignition and place
the ignition in the ON/RUN mode to disarm the security
system.
Remote Keyless Entry (RKE) Key Fob Keyless
Enter-N-Go
NOTE: You can insert the double-sided emergency key
into the door lock cylinder with either side up.
Removing Key Fob From Ignition
Place the gear selector in PARK (if equipped with an
automatic transmission). Turn the Key Fob to the OFF
position and then remove the Key Fob.
NOTE:
• The power window switches, radio, power sunroof (if
equipped), and power outlets will remain active for up
to 10 minutes after the ignition switch is turned to the
OFF position. Opening either front door will cancel
this feature. Refer to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
• For vehicles not equipped with a touchscreen radio,
refer to “Electronic Vehicle Information Center
(EVIC)” in “Understanding Your Instrument Panel”
for further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
• For vehicles equipped with a touchscreen radio, refer
to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
CAUTION!
• If your vehicle battery becomes low or dead, your
RKE Key Fob will become locked in the ignition.
• Do not attempt to remove the RKE Key Fob while
in this condition, damage could occur to the RKE
Key Fob or ignition module. Only remove the
emergency key for locking and unlocking the
doors.
• Leave the RKE Key Fob in the ignition and either:
• Jump Start the vehicle.
• Charge the battery.
2
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
WARNING!
• Before exiting a vehicle, always shift the automatic
transmission into PARK or the manual transmission into REVERSE, apply the parking brake, turn
the vehicle OFF, remove the RKE Key Fob from the
ignition and lock your vehicle. If equipped with
Keyless Enter-N-Go, always make sure the keyless
ignition node is in “OFF” mode, remove the RKE
Key Fob from the vehicle and lock the vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle.
• Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Children should be warned not to touch the parking
brake, brake pedal or the gear selector.
(Continued)
WARNING! (Continued)
• Do not leave the RKE Key Fob in or near the
vehicle, or in a location accessible to children, and
do not leave the ignition of a vehicle equipped
with Keyless Enter-N-Go in the ACC or ON/RUN
mode. A child could operate power windows, other
controls, or move the vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
CAUTION!
An unlocked vehicle is an invitation. Always remove
the RKE Key from the ignition and lock all doors
when leaving the vehicle unattended.
Key-In-Ignition Reminder
Opening the driver’s door when the Key Fob is in the
ignition and the ignition switch position is OFF or ACC,
a chime will sound to remind you to remove the Key Fob.
NOTE:
• ⬙Keyed⬙ Ignition systems will chime in OFF or ACC
when the driver door is open.
• “Keyless⬙ Ignition systems will chime in ACC or RUN
when the driver door is open.
• If equipped with Electronic Vehicle Information Center
(EVIC)/Driver Information Display (DID), the EVIC or
DID will display “Key In Ignition.”
General Information
The following regulatory statement applies to all Radio
Frequency (RF) devices equipped in this vehicle:
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
SENTRY KEY
The Sentry Key Immobilizer System prevents unauthorized vehicle operation by disabling the engine. The
system does not need to be armed or activated. Operation
is automatic, regardless of whether the vehicle is locked
or unlocked.
2
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
The system uses a RKE Key Fob, an Ignition Node
Module, Keyless Push Button Ignition and a RF receiver
to prevent unauthorized vehicle operation. Therefore,
only RKE Key Fobs that are programmed to the vehicle
can be used to start and operate the vehicle. The system
will not allow the engine to crank if an invalid RKE Key
Fob is used to start and operate the vehicle. The system
will shut the engine off in two seconds if an invalid RKE
Key Fob is used to start the engine.
someone used an invalid RKE Key Fob to try to start the
engine. Either of these conditions will result in the engine
being shut off after two seconds.
If the Vehicle Security Light turns on during normal
vehicle operation (vehicle running for longer than 10
seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon
as possible by an authorized dealer.
NOTE: A RKE Key Fob that has not been programmed is
also considered an invalid key.
During normal operation, after placing the keyless ignition in the ON/RUN position, the Vehicle Security Light
will turn on for three seconds for a bulb check. If the light
remains on after the bulb check, it indicates that there is
a problem with the electronics. In addition, if the light
begins to flash after the bulb check, it indicates that
CAUTION!
The Sentry Key Immobilizer system is not compatible with some aftermarket remote starting systems.
Use of these systems may result in vehicle starting
problems and loss of security protection.
All of the RKE Key Fobs provided with your new vehicle
have been programmed to the vehicle electronics.
Replacement RKE Key Fobs
NOTE: Only RKE Key Fobs that are programmed to the
vehicle electronics can be used to start and operate the
vehicle. Once a RKE Key Fob is programmed to a vehicle,
it cannot be programmed to any other vehicle.
CAUTION!
• Always remove the RKE Key Fobs from the vehicle
and lock all doors when leaving the vehicle unattended.
• For vehicles equipped with Keyless Enter-N-Go —
Ignition, always remember to place the ignition in
the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21
NOTE: Duplication of RKE Key Fobs may be performed
at an authorized dealer. This procedure consists of programming a blank RKE Key Fob to the vehicle electronics. A blank RKE Key Fob is one that has never been
programmed.
When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to an authorized
dealer.
Customer RKE Key Fob Programming
Programming RKE Key Fobs may be performed at an
authorized dealer.
General Information
The following regulatory statement applies to all radio
frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
2
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
VEHICLE SECURITY ALARM
The Vehicle Security Alarm monitors the vehicle doors
and ignition for unauthorized operation. When the Vehicle Security Alarm is activated, interior switches for
door locks are disabled. The system provides both audible and visible signals for the first three minutes the
horn will sound and the headlights will turn on, the park
lamps and/or turn signals will flash and Vehicle Security
Light will flash repeatedly. For an additional 15 minutes
only, the headlights will turn on, the park lamps and/or
turn signals, and Vehicle Security Light will flash.
Rearming Of The System
The Vehicle Security Alarm will rearm itself after the 15
additional minutes of headlights and Vehicle Security
Light flashing, if the system has not been disabled. If the
condition which initiated the alarm is still present, the
system will ignore that condition and monitor the remaining doors and ignition.
To Arm The System
Follow these steps to arm the Vehicle Security Alarm:
1. Remove the key from the ignition system (refer to
⬙Starting Procedures⬙ in ⬙Starting And Operating⬙ for
further information).
• For vehicles equipped with Keyless Enter-N-Go —
Ignition, make sure the vehicle ignition system is
⬙OFF.⬙
• For vehicles not equipped with Keyless Enter-N-Go
— Ignition, make sure the vehicle ignition system is
⬙OFF⬙ and the key is physically removed from the
ignition.
2. Perform one of the following methods to lock the
vehicle:
• Push LOCK
button on the interior power door
lock switch with the driver and/or passenger
door open.
• Push the LOCK
button on the exterior Passive
Entry Door Handle with a valid Key Fob available
in the same exterior zone (refer to ⬙Keyless EnterN-Go — Passive Entry⬙ in ⬙Things To Know Before
Starting Your Vehicle⬙ for further information).
• Push the LOCK
button on the RKE Key Fob.
3. If any doors are open, close them.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23
The Vehicle Security Alarm will set when you use the
power door locks, or use the RKE Key Fob to lock the
doors. After all the doors are locked and closed, the
Vehicle Security Light, in the instrument panel cluster,
will flash rapidly for about 16 seconds to indicate that the
alarm is being set. After the alarm is set, the Vehicle
Security Light will flash at a slower rate to indicate that
the system is armed.
To Disarm The System
The Vehicle Security Alarm can be disarmed using any of
the following methods:
1. Push the UNLOCK
button on the RKE Key Fob.
2. Grasp the Passive Entry Unlock Door Handle with a
valid RKE Key Fob within 5 ft (1.5 m) of the passive
entry door handle (if equipped, refer to ⬙Keyless
Enter-N-Go — Passive Entry⬙ in ⬙Things To Know
Before Starting Your Vehicle⬙ for further information).
2
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
3. Cycle the ignition out of the OFF position.
• For vehicles equipped with Keyless Enter-N-Go —
Ignition, push the Keyless Ignition
button (requires at least one valid RKE Key Fob in the
vehicle).
• For vehicles not equipped with Keyless Enter-N-Go,
insert a valid key into the ignition switch and turn
the key to the ON position.
The Vehicle Security Alarm is designed to protect your
vehicle. However, you can create conditions where the
system will give you a false alarm. If one of the previously described arming sequences has occurred, the
Vehicle Security Alarm will arm regardless of whether
you are in the vehicle or not. If you remain in the vehicle
and open a door, the alarm will sound. If this occurs,
disarm the Vehicle Security Alarm.
If the Vehicle Security Alarm is armed and the battery
becomes disconnected, the Vehicle Security Alarm will
remain armed when the battery is reconnected; the
exterior lights will flash, and the horn will sound. If this
occurs, disarm the Vehicle Security Alarm.
Security System Manual Override
The Vehicle Security Alarm will not arm if you lock the
doors using the manual door lock plunger.
ILLUMINATED APPROACH
The courtesy lights will turn on when you use the RKE
Key Fob to unlock the doors or open any door.
This feature also turns on the approach lighting in the
outside mirrors (if equipped). Refer to “Mirrors” in
“Understanding The Features Of Your Vehicle” for further information.
The lights will fade to off after approximately 30 seconds,
or they will immediately fade to off once the ignition
switch is turned to ON/RUN from the OFF position.
The front courtesy overhead console and door courtesy
lights will not turn off if the dimmer control is in the
“Dome ON” position (rotate horizontal thumb wheel on
the bottom of the switch to the far right detent position).
The illuminated entry system will not operate if the
dimmer control is in the “Dome OFF” position (rotate
horizontal thumb wheel on the bottom of the switch to
the far left detent position).
NOTE: If your vehicle is equipped with illuminated
approach lights under the outside mirrors, they can be
turned off by using the Electronic Vehicle Information
Center (EVIC) or Driver Information Display (DID) controls (if NOT equipped with a touchscreen radio) or the
Uconnect radio (if equipped with a touchscreen radio).
Refer to “Electronic Vehicle Information Center (EVIC),”
“Driver Information Display (DID),” or “Uconnect Settings” in “Understanding Your Instrument Panel” for
further information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25
REMOTE KEYLESS ENTRY (RKE)
The RKE system allows you to lock or unlock all doors,
tailgate, and the RamBox (if equipped) as well as activate
the Panic Alarm from distances up to approximately 66 ft
(20 m) using a hand-held radio Key Fob with integrated
key. The RKE Key Fob does not need to be pointed at the
vehicle to activate the system. Push and release the
LOCK button on the RKE Key Fob to lock all doors, the
tailgate and the RamBox (if equipped). The turn signal
lights will flash and the horn will chirp to acknowledge
the signal.
NOTE: Inserting the Key Fob with RKE Key Fob into the
ignition switch disables the system from responding to
any button pushes from that RKE Key Fob. Driving at
speeds 5 mph (8 km/h) and above disables the system
from responding to all RKE Key Fob buttons for all RKE
Key Fobs.
2
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Remote Keyless Entry (RKE) Key Fob (IGNM) RKE Key Fob Keyless Enter-N-Go
Remote Unlock The Doors
Push and release the UNLOCK
Key Fob once to unlock the driver’s door. Push the
unlock
button twice within five seconds to unlock
all doors, the tailgate and the RamBox (if equipped).
button on the RKE
The turn signal lights will flash to acknowledge the
unlock signal. The illuminated entry system will also
turn on.
NOTE: The EVIC/DID or Uconnect Settings are setup for
driver door first, otherwise this will unlock all doors.
Remote Key Unlock, Driver Door/All Doors First
This feature lets you program the system to unlock either
the driver’s door or all doors on the first push of the
UNLOCK button on the RKE Key Fob. To change the
current setting, proceed as follows:
• For vehicles not equipped with a touchscreen radio,
refer to “Electronic Vehicle Information Center
(EVIC)/ Settings (Customer-Programmable Features)”
in “Understanding Your Instrument Panel” for further
information.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27
• For vehicles equipped with a touchscreen radio, refer
to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
NOTE: Pushing the LOCK button on the RKE Key Fob
while you are inside the vehicle will activate the Vehicle
Security Alarm System. Opening a door with the Vehicle
Security Alarm System activated will cause the alarm to
sound. Push the UNLOCK button to deactivate the
Vehicle Security Alarm System.
Flash Lamps With Remote Key Lock
This feature will cause the turn signal lights to flash when
the doors are locked or unlocked with the RKE Key Fob.
This feature can be turned on or turned off. To change the
current setting, proceed as follows:
• For vehicles not equipped with a touchscreen radio,
refer to “Electronic Vehicle Information Center
2
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
(EVIC)/Settings (Customer-Programmable Features)”
in “Understanding Your Instrument Panel” for further
information.
• For vehicles equipped with a touchscreen radio, refer
to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
To Lock The Doors
Push and release the LOCK
button on the RKE Key
Fob to lock all doors, the tailgate and the RamBox (if
equipped). The turn signal lights will flash and the
horn will chirp to acknowledge the signal.
Sound Horn With Remote Key Lock
This feature will cause the horn to chirp when the doors
are locked with the RKE Key Fob. This feature can be
turned on or turned off. To change the current setting,
proceed as follows:
• For vehicles not equipped with a touchscreen radio,
refer to “Electronic Vehicle Information Center
(EVIC)/Settings (Customer-Programmable Features)”
in “Understanding Your Instrument Panel” for further
information.
• For vehicles equipped with a touchscreen radio, refer
to “Uconnect Settings” in “Understanding Your Instrument Panel” for further information.
NOTE: Pushing the LOCK
button on the RKE Key
Fob while you are in the vehicle will activate the
Vehicle Security Alarm System. Opening a door with
the Vehicle Security Alarm System activated will cause
the alarm to sound. Push the UNLOCK
button to
deactivate the Vehicle Security Alarm System.
Using The Panic Alarm
To turn the Panic Alarm feature ON or OFF, push and
hold the
button on the RKE Key Fob for at least one
Loading...