Rally Armor 2012-14 Impreza User Manual
IMF 22
YOUR 2012+ IMPREZA MOUNTING HARDWARE CONSISTS OF:
HOW TO REMOVE STOCK FASTENERS:
Quantity
Hardware Item
Item ID
2
Front brackets
HMF22-FR-BR
2
Rear Brackets
HMF14/16-R-BR
2
Side Skirt Front Spacers
SSK-SP
10
Round Edge Clips
RoCl
6
Polygon Clips
PolCl
2
Plastic Inserts
Ins3
14
Long Stainless Steel Screws
1.5SS
2
Short Stainless Steel Screws
1SS
16
Washers
SmWash
2
Spacers
.5SP
2
Front Screw Tip Covers
Scrwcvr
Cautionary Tip: The hardware is strong and self threading but over-tightening the
clips is not advised.
Installation Tip: To ease installation and avoid damage to existing OEM clips during
removal, a well lit, climate controlled installation environment is recommended.
To the installer: Please return these instructions to the customer
after installation. Always test and check wheel clearances before
returning vehicle.
To the customer: Retain these instructions after installation. They
may be necessary for installing other optional parts or removal of
this accessory.
2012+ SUBARU IMPREZA HATCH/SEDAN MUD FLAP INSTALLATION INSTRUCTIONS
PLEASE REVIEW THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING INSTALLATION
For high resolution color images of these instructions, please visit http://www.rallyarmor.com
To protect your Rally Armor mud flaps, care must be taken during parking and reversing. Rally Armor always recommends professional installation.
Check wheel clearances after installation, especially on vehicles outfitted with non-OEM offset wheels and suspensions. Adjust accordingly.
Rally Armor is not responsible for damage or loss of installed mud flaps.
Each mud flap set contains 4 flaps and mounting hardware (unless otherwise noted).
Recommended tools: Offset or ratcheting screwdriver, short Phillips screwdriver, small & long flat head screwdrivers.
Version 1.1 Release Date 08.05.2012 1
IMF 22
Front Mud Flap Installation
Begin by parking the vehicle on an even surface. Turn the steering wheel to allow access to the inner wheel well area.
• (Figure A) Remove fender liner clip. On side skirt equipped vehicles, remove first two retaining clips.
• (Figure B) Remove the four OEM fender liner fasteners (as shown). Carefully unclip front portion of side skirt by pulling the outer
edge away just enough to release first two horizontal retainer clips. Pull liner away to gain access to the interior fender area.
• (Figure C) Place 3 supplied round edge clips (RoCl ) over mounting tabs at an angle (as shown). Reinstall liner and side skirt.
• (Figure D) Side skirt equipped vehicles: angle front bracket (HMF22-FR-BR) between the exposed section of the skirt and liner.
Interior portion of bracket is positioned against wall of wheel well. Place polygon clip (PolCl) over the inside bracket mounting point.
• (Figure E) Vehicles without side skirts: position front bracket (HMF22-FR-BR) at an angle underneath and flush against liner. Ensure
inner bracket is positioned against the wall of the wheel well.
• (Figure F) Secure bracket by mounting insert (Ins3) FLUSH through the side skirt and bracket. Place polygon clip (PolCl) over the
interior mounting point of the bracket. Important- BEFORE mounting insert (Ins3), pull inner stem OUT. Install the fastener where
the OUTER assembly is flat against the body or side skirt. Push stem into retainer, locking it into place.
•
• (Figure G) Mount the front mud flap with the logo facing the rear of the vehicle. Place the front mud flap against the corresponding
mounting points on the vehicle and bracket. Thread long screws (1.5SS) with washers (SmWash) through the flap and into each the 4
mounted clips. On the innermost mounting point of the bracket, place a spacer (.5SS) between the mud flap and polygon clip. Replace
Version 1.1 Release Date 08.05.2012 2
Loading...