RFA-Z105-2 EMU-2™
Quick Start
EMU-2™ Energy Monitoring Unit
Quick Start Guide
FCC/IC Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
FCC/IC RF Exposure Statement
This equipment complies with FCC and Industry Canada radiation exposure limits set forth for an uncontrolled
environment. The antenna(s) used for this equipment must be installed to provide a separation distance of at least 8
inches (20cm) from all persons.
ICES-003 Compliance
This Class B digital apparatus complies with Canadian ICES-003.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Compliance Regulations For Australia and New Zealand
This equipment complies with the C-Tick labeling requirements for Australia and in New Zealand. As a radio
transmitter, this device complies with the requirements of AS/NZS 4268:2008 as designated in the
Radiocommunications (Short Range Devices) Standard 2004 for Australia and as required by the
Radiocommunications Regulations (General Users Radio License for Short Range Devices) Notice 2011 for New
Zealand. This device is a Category A device as defined in the Radiocommunications (Compliance Labeling Electromagnetic Radiation) Notice 2003.
www.rainforestautomation.com
www.rainforestautomation.com
Install Code
MAC
Address
--:----
--- --, ----
Top Button increments
digit value
Bottom Button saves
digit value
Set Rate
000.00¢/kWh Change
Keep
Step 1: Check Contents of the box
The box should contain the following items:
EMU-2™ Display unit, AC Power Adapter, 2 x AAA batteries
Step 2: Register your EMU-2™
Your EMU-2™ must be registered with your utility to connect to the smart meter. It may come to you
preregistered. If so, you can skip to the next step. If not, you will need to contact your utility to
register your device. You will need the following information, which is found on the Information Label
on the back of your EMU-2™:
Note that it may take some time for your utility to enable the smart meter to connect with your
device. You must wait until this process is complete before proceeding; your EMU-2™ will not
function correctly until the smart meter is enabled.
RFA-Z105-2 EMU-2™
Quick Start
Step 3: Power up your EMU-2™
Plug the AC Adapter into a power outlet, and plug the other end of the cord into your EMU-2™.
You can also install the batteries, if you wish: remove the battery door at the back of the unit; insert 2
AAA batteries exactly as shown on inside of the battery compartment; replace the battery cover.
Note that putting a battery in backwards can be hazardous, and may cause extensive damage to
your EMU-2™. Always use alkaline batteries; never mix battery types. Replace all batteries at the
same time
Step 4: Wait for your EMU-2™ to join the smart meter
The EMU-2™ will attempt to connect to the smart meter. This could take 1-2
minutes. When your EMU-2™ finds the smart meter and successfully
communicates with it, you will see the Current Time screen, with dashes
instead of digits. As soon as the dashes are replaced with the current time
and date, it means that your EMU-2™ is reading the meter data.
Step 5: Configure your EMU-2™
a. Press both of the buttons on your EMU-2™ simultaneously and release.
b. Press the Bottom Button to skip the Restart screen.
c. Press the Top Button to select the language
you would like to use; press the Bottom Button
to save your selection.
d. If your meter does not provide pricing (ask your
utility), you will need to set your electricity price.
The digit to be modified will be flashing, starting
on the right, and working left. After you have
entered all 5 digits of the energy price, you will
see the Billing Dates screen.
e. Press the Bottom Button to see the Battery screen.
f. Press any button to return to the Current Time screen. Your EMU-2™ is ready to use.
Loading...