Raindrip RSC600i Installation & Programming

Smart Controller

Installation

& Programing

RSC600i

watch the video at raindrip.com/smart

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:51 PM Page 1

Support

watch the video at raindrip.com/smart

Installation & Programming

Product Information

The model and serial numbers are located at the rear of the
controller. Record these numbers in the space provided
below. Have these numbers available when contacting
Technical Support.

MODEL NO.:

SERIAL NO.:

Additional Support

If additional support is required after reading the instructions
in this guide, then Internet Video Support or Technical Phone
Support is available.

Internet Video Support:

raindrip.com/smart

Technical Phone Support: 877-502-7952

Monday - Friday 8:00 AM - 5:00 PM (Pacific Standard Time)
Saturday - Sunday 9:00 AM - 1:00 PM (Pacific Standard Time)

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:51 PM Page 2

Smart Controller Technology . . . . . . . . . . . . . . . . . . .1

Irrigation System Overview . . . . . . . . . . . . . . . . . . .2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Smart Controller Features . . . . . . . . . . . . . . . . . . . .4

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6

Installation Requirements . . . . . . . . . . . . . . . . . . . . .7

Installation Mount Docking Station . . . . . . . . . . . .8

Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Dock Controller . . . . . . . . . . . . . . . . . . .10

Programming: Settings . . . . . . . . . . . . . . . . . . . . .11-12

Programming: Edit Schedule . . . . . . . . . . . . . . . .13-16

Auto Run (ON / SKIP / OFF) . . . . . . . . . . . . . . . . . .17

Water Now . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Disabling Smart Mode . . . . . . . . . . . . . . . . . . . . . . .19

Rain Sensor / Switch . . . . . . . . . . . . . . . . . . . . . . .20

Operational Notes . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . .22

FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Programming Aid - Introduction . . . . . . . . . . .25-26

Programming Aid - Example . . . . . . . . . . . . . .27-28

Programming Aid - Worksheet . . . . . . . . . . . .29-30

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table of Contents

watch the video at raindrip.com/smart

Installation & Programming

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:51 PM Page 3

Smart Controller Technology

watch the video at raindrip.com/smart

Installation & Programming

1

Smart controllers can reduce water consumption as
much as 30% by optimizing the amount of water
applied to landscaping. A smart controller applies
100% of the programmed watering duration during
the hottest months of the year and reduces watering
durations for cooler months. Watering duration
compensation factors are based on 10 years of
historical weather data for specific zip code regions.

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

jan feb mar apr may jun jul aug sep oct nov dec

Typical Monthly Water Savings %

*results will vary by zip code region

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:53 PM Page 1

watch the video at raindrip.com/smart

Installation & Programming

2

illustration 3

E

E

D

A

B

D

C

A. Controller

B. Wires

C. Valves and Solenoids

D. Sprinkler Zones

E. Drip Irrigation Zones

Irrigation System Overview

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 2

watch the video at raindrip.com/smart

Installation & Programming

3

Package Contents

❶ Smart Controller / Docking Station
❷ AC Power Supply
❸ Mounting Hardware

a. #8 X 11/4" Screws (4)
b. Drywall Anchors (4)

❹ Installation & Programming Guide
❺ Registration Card

❶

❷

❸

❹ ❺

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 3

Smart Controller Features

RSC600i

watch the video at raindrip.com/smart

Installation & Programming

4

• 6 zones with up to 4 independent watering cycles per day per zone.

• Automatically adjusts watering duration based on historical weather

patterns for your zip code and time of year.

• Daily and Year-to-Date water savings displayed.

• Built-in diagnostics automatically troubleshoots and alerts of wiring issues.

• Audible beeps to alert for low batteries, wiring faults, and other user

interface actions.

• "Skip" function allows for manual interruption of watering schedule for

yard work and other activities.

• "Water Now" function allows for manual watering to test irrigation system.

• Rain Sensor / Switch ready - works with most major brands.

• Easy to read, oversized backlit display.

• Controller "undocks" to allow for comfortable / convenient programming.

• Automatically adjusts for daylight savings.

• Optional conventional timer mode (non-smart).

• Requires 2 AA batteries (not included).

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 4

Overview

RSC600i

watch the video at raindrip.com/smart

Installation & Programming

5

❶ LCD Display – Displays status of the controller. (page 21-22)
❷ Navigation Pad – Used to select, change, and enter values.

• LEFT and RIGHT arrows to move left or right.

• UP and DOWN arrows to increase or decrease values.

• ENTER saves all values and advances to next screen.

❸ Settings – View or change DATE, TIME, ZIP CODE, and

WATERING DAYS option. (page 11-12)

❹ Edit Schedule – View or change the WATERING SCHEDULE. (page 13-16)
❺ Auto Run – Change operating mode to ON / SKIP / OFF. (page 17)
❻ Water Now – Manual watering Start / Stop. (page 18)
❼ A/C Power Connection – External power connection.
❽ Valve Solenoid Wire Terminals – Color coded quick connect terminals.
❾ Rain Sensor / Switch Terminals – For rain sensor / switch wiring

(optional). No additional programming required. (page 20)

❿ Reset – Stops watering; clears controller memory of any errors;

and returns controller to the idle state. DATE, TIME, ZIP CODE,
WATERING DAYS option, and WATERING SCHEDULE are not erased.

⓫ Removable Cover – To access SETTINGS, EDIT SCHEDULE, and RESET

buttons.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 5

Overview

RSC600i

watch the video at raindrip.com/smart

Installation & Programming

6

❼

⓫

❶

❺

❸

❷

❻

❹

❿
❾

❽

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 6

watch the video at raindrip.com/smart

Installation & Programming

7

Items Required for Installation

• Docking Station (provided)

• #8 X 11⁄4" screws (4) (provided)

• Drywall anchors (4) (provided)

• Phillips head screwdriver

• Wire strippers

• Power drill (if drywall anchors are to be used)

• 1/4" drill bit (if drywall anchors are to be used)

• Sprinkler wire (18 gage, solid copper wire recommended)

Installation Requirements

Note: If replacing an existing irrigation timer, label each of the
wires as they are removed from the old timer so they can be
placed in the same position on the RSC600i.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 7

watch the video at raindrip.com/smart

8

Docking Station Installation - Indoors Only

For new installations

• Locate near sprinkler wires from
irrigation system valve solenoids.

• Locate within 48" of a 110 volt AC outlet.

Mount the docking station

• Undock and set the controller aside.

• At the selected location, hold
the docking station on the wall.

• Using the docking station as a template,
mark the four screw locations on the wall.

• If drywall anchors are needed, drill a 1/4"
hole in the wall at each marked location.

• Insert a drywall anchor in each hole so that
it is flush with the wall surface.

• Position the docking station over the anchors.

• Insert and tighten one #8 X 1

1

⁄4" screw in

each of the four holes. Do not overtighten screws.

Installation: Mount Docking Station

Installation & Programming

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 8

watch the video at raindrip.com/smart

Installation & Programming

9

Wiring the Docking Station

These instructions assume your irrigation system is properly installed and
the valve solenoid wires are available at the controller mounting location.

CAUTION: Do not connect more than one wire to each
terminal. Damage to the controller will occur.

Common Wire Connections

• Insert the common wire from the solenoids to a "COMMON"

terminal (white) at the bottom of the docking station.

Zone Wire Connections

• Insert one control wire from a specific solenoid (zone 1) to a

corresponding "ZONES" terminal (blue 1) at the bottom of the
docking station. Repeat for each zone solenoid.

• Check wires to ensure they

are fully seated and secure.

• Plug A/C Power Suppy

connector to the "24 VAC
POWER" terminal (red), then
plug the Power Supply into a
110 volt outlet.

Installation: Wiring

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:56 PM Page 9

Docking the Controller

• Remove display protective film.

• Install AA batteries in the back of the controller.

• Place the back of the controller against the docking station

• Slide the controller downward until it is firmly seated at the

bottom of the docking station.

• Confirm UNDOCKED indicator is turned off.

The controller is ready for programming and operation.

Installation: Dock Controller

watch the video at raindrip.com/smart

Installation & Programming

10

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 10

Remove Cover

View or change DATE, TIME, ZIP CODE, and WATERING DAYS option.

Programming: Settings

watch the video at raindrip.com/smart

Installation & Programming

11

1. Press SETTINGS button

2. Adjust CURRENT DATE.
Press ENTER.

3. Adjust CURRENT TIME
(note AM or PM).
Press ENTER.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 11

Programming: Settings

watch the video at raindrip.com/smart

Installation & Programming

12

4. Adjust your local ZIP CODE.
Press ENTER.

• If ENTER ZIP CODE ERROR is displayed;

the zip code is not recognized.

-Check the entered zip code number.

-Use a neighboring zip code if necessary.

5. Select WATERING DAYS option.
Press ENTER.

-Option 1: (see page 13)

“WATER ON SPECIFIC DAYS OF WEEK”

-Option 2: (see page 14)

“WATER ON ODD OR EVEN DATES OF MONTH”

SETTINGS are now complete.

Note: To operate the controller
as a conventional (non-smart)
timer, see page 19.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 12

Remove Cover

View or change WATERING DAYS option.

Programming: Edit Schedule

watch the video at raindrip.com/smart

Installation & Programming

13

1. Use Programming Aid to facilitate
watering schedule programming
(pages 25 thru 30)

2. Press EDIT SCHEDULE button

3. Adjust number of watering CYCLES
for each day.

4. After CYCLES have been set for all
days, then press ENTER.

5. Repeat for all ZONES.

(continued)

Option 1: WATER ON SPECIFIC DAYS OF WEEK

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 13

Programming: Edit Schedule

watch the video at raindrip.com/smart

Installation & Programming

14

1. Use Programming Aid to facilitate
watering schedule programming
(pages 25 thru 30)

2. Press EDIT SCHEDULE button

3. Select ODD DATES or EVEN DATES.

4. Adjust number of watering
CYCLES, then press ENTER.

5. Repeat for all ZONES.

(continued)

Option 2: WATER ON ODD OR EVEN DATES OF MONTH

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 14

View or change WATERING SCHEDULE START TIME and DURATION.

Programming: Edit Schedule

watch the video at raindrip.com/smart

Installation & Programming

15

AM/PM

«

Start time
Cycle #

Zone #

Duration

6. Adjust DURATION (1-99 minutes).

-Set DURATION for the hottest month of the year.

7. Adjust START TIME (note AM or PM). Press ENTER.

8. Repeat for remaining ZONES and watering CYCLES.

WATERING SCHEDULE programming is now complete.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 15

Programming: Edit Schedule

watch the video at raindrip.com/smart

Installation & Programming

16

WATERING SCHEDULE Notes:

• Zone watering schedules are reserved to avoid duplicate or
overlapping START TIMES and DURATIONS. During programming,
START TIMES may skip to the next available time slot.

• DURATION should be set before setting a START TIME.

• Watering schedule entries can be reviewed and corrected at any
time during programming by pressing the EDIT SCHEDULE button.

• START TIMES and DURATIONS are restricted so that watering
cannot cross midnight.

• The automatically adjusted minimum watering duration will be
one (1) minute. If the adjusted duration is less that 30 seconds,
the actual watering duration will be zero (0) minutes and no
watering will occur for that specific zone.

• To erase ALL watering schedule programs, press and hold EDIT
SCHEDULE for 5 seconds.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 16

Change AUTO RUN mode to ON, SKIP, or OFF.

Auto Run (ON / SKIP / OFF)

watch the video at raindrip.com/smart

Installation & Programming

17

On Mode Skip Mode Off Mode

Press AUTO RUN button to select ON, SKIP, or OFF mode.

ON: Controller is in automatic watering mode.

SKIP: Controller will “skip” watering for a selected time period.

1. Input DURATION (1 to 99 hours).

2. Press ENTER to start the skip cycle.

• After SKIP cycle completes, the controller will return
to the previous operating mode (ON or OFF).

SKIP programming is now complete.

OFF: Controller is “off” and will not execute any watering schedule program.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 17

Initiate Manual Watering.

Water Now

watch the video at raindrip.com/smart

Installation & Programming

18

1. Press WATER NOW button.

2. Select a specific ZONE (1-6).
If ALL is selected, all zones will
water sequentially.

3. Input DURATION (1-99 minutes).

4. Press ENTER to start manual
watering cycle.

WATER NOW programming is now complete.

WATER NOW Notes:

• To stop a manual watering cycle, press the WATER NOW button again.

• After a manual watering cycle is complete, the controller

will return to the previous operating mode (ON, SKIP, or OFF).

-The operating mode can be changed during a manual
watering cycle by pressing the AUTO RUN button.

-Pressing AUTO RUN, SETTINGS or EDIT SCHEDULE
button will not stop a manual watering cycle.

• WATER NOW manual watering cycles are not included in
TODAY or YTD water savings calculations.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 18

watch the video at raindrip.com/smart

Installation & Programming

19

Operate controller as a conventional (non-smart) timer.

1. Press SETTINGS.

2. Press ENTER (do not change DATE).

3. Press ENTER (do not change TIME).

4. Change ZIP CODE to all zeroes. Press ENTER.

5. Press ENTER (do not change WATERING
SCHEDULE method).

Smart mode is now disabled.

To enable Smart mode, repeat steps 1-5 above and
enter your local ZIP CODE as shown on page 12.

Conventional Timer Mode Notes:

• The ZIP CODE indicator will flash slowly as a

reminder the controller is in conventional timer mode.

• Disabling Smart mode will not change WATERING

METHOD or WATERING SCHEDULE program.

• TODAY WATER SAVINGS will display 00%.

• Watering durations will not be reduced seasonally.

• Water savings may not be realized.

Disabling Smart Mode

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 19

Connect a conventional two wire rain sensor / switch.

1. Mount rain sensor per the manufacturer's
installation instructions.

2. Remove rain sensor jumper wire.

-Press square plunger down.

-Remove yellow jumper wire.

3. Connect wires from rain sensor to terminal strip.

-Press square plunger down.

-Insert sensor wires into yellow terminal blocks
(ignore color of sensor wires).

NOTE: The controller cannot send a watering signal to valve
solenoids if the jumper wire is removed and a rain sensor is not
connected. Actual watering will not occur.

Rain Sensor / Switch is ready for use.

Examples of compatible Rain Sensor / Switch:

• Nelson

®

8501 Rain-Trip™• Rainbird®RSD-CEx

• Hunter

®

Mini-Clik

®

• Hunter®Rain-Clik

™

• Toro®TRS

Rain Sensor / Switch

watch the video at raindrip.com/smart

Installation & Programming

20

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 20

NOTE: The controller cannot send a watering signal to valve solenoids
when the controller is "undocked". Actual watering will not occur.

Operational Notes

watch the video at raindrip.com/smart

Installation & Programming

21

Undocked - Using Battery Power

• The LCD backlight will not illuminate when the controller is undocked and
running on battery power.

• If buttons are not pressed within a 1 minute time period, the LCD display will
automatically turn off (blank) to conserve battery life. The controller clock will
continue to operate.

• To reactivate the LCD display, press and hold any button for 2 seconds.

• Battery power is used for keeping current time and for undocked programming
only when A/C power is not available (power loss or undocked). Watering
schedule program is maintained in controller memory.

Docked - Using Wall Outlet A/C Power

• The LCD backlight will automatically turn off after buttons are not pressed
within a 3 minute time period.

• To reactivate the backlight, press any button.

Audible Beeps

• Docking and Undocking - rapid triple beep

• LOW BATTERY - single beep every 15 seconds.

• ERROR Check Valve Wires - single beep every 15 seconds.

• Upper or Lower Start Time Value Reached (when programming) - single beep

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 21

Status Indicators

watch the video at raindrip.com/smart

Installation & Programming

22

SHUTDOWN
RAIN FORECAST

UNDOCKED

CONTROLLER

IN

LOW BATTERY

CODEZIP

ERROR

VALVE WIRES

CHECK

ERROR

❹

❸

❷
❶

❺

Status Indicator Notes

❶ UNDOCKED – The controller is "undocked" or not fully seated in
the docking station.

❷ LOW BATTERY – Indicates batteries are low and need to be
replaced. All programming and settings (except current time) will be
maintained during battery replacement.

❸ ZIP CODE ERROR – The entered zip code was not recognized.
See SETTINGS on page 12.

❹ ERROR CHECK VALVE WIRES – A wiring fault was detected
during watering of a specific zone. The specific zone number will
also be displayed. Check for shorted wires or faulty solenoid.

❺ SHUTDOWN RAIN FORECAST – The controller will not water
when this indicator is on. If an optional rain sensor / switch is used,
then this indicator will turn on when the rain sensor / switch detects a
rain event.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 22

FAQ

23

1. Can I use the controller for both drip and sprinkler systems?

Yes. Independent durations and multiple watering cycles for each zone allow you to program various
watering schedules as necessary.

2. Can I use my existing wires to my valves?

Yes. This controller is compatible with commonly used landscape irrigation systems.

3. Can I install the controller outdoors?

Installation outdoors is not recommended.

4. How many valves can be controlled by one zone output terminal?

Only one valve can be controlled per zone output terminal. Damage to the unit may occur if more than one
valve is connected to a zone terminal.

5. What if my zip code is new or not recognized by the controller?

Use a nearby neighboring zip code.

6. How do I know what duration to program into the controller?

Set your watering durations for the hottest part of the year. If replacing a standard timer, use the durations
from the watering program of your previous timer.

7. Why do I need more than one cycle or start time per day?

If your landscape soil is not easily penetrated by moisture or the landscape is sloped it can be beneficial to
run a short watering cycle first to loosen the soil followed by a normal watering cycle.

8. Will my controller stop watering when it rains?

The controller will not stop watering unless an optional rain sensor is installed. The controller will accept
most major brands of rain sensors (see page 20).

9. What if it's raining and I don't have a rain sensor?

The SKIP function can be used to interrupt all programmed watering schedules for up to 99 hours. When
the SKIP function ends, the controller will return to the previously set operating mode (ON or OFF).

10. Why does my landscape appear to be dry?

Your maximum summer watering duration may need to be adjusted if dryness is frequently observed. If
necessary, you can supplement your programmed watering during hotter than normal weather by using the
WATER NOW feature.

11. Do the valves operate when the controller is undocked?

No. The controller cannot operate valves when it is undocked.

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 23

Troubleshooting

watch the video at raindrip.com/smart

Problem Possible Cause Solution

No Backlight; Blank Display
(wall power)

a) No power to controller Check power wires and circuit breakers

No Backlight; Normal Display
(wall power) (see page 21)

a) Backlight is in sleep mode

Press/Release any button to activate
backlight

No Backlight (battery power)
(see page 21)

a) Normal operation to conserve battery

life

Normal operation

Blank display (battery power)
(see page 21)

a) Display is in sleep mode

Press/Hold any button for at least 2
seconds

b) Weak or dead batteries Replace batteries

Controller does not respond when
buttons are pressed

a) Electrical surge Press/Release reset button

Controller beeps once every 15
seconds (see page 21)

a) LOW BATTERY indicator is on Replace batteries

b) ERROR CHECK VALVE WIRES indicator

is on

Note zone on display; Check / Repair
shorted wires or faulty valve solenoid

No watering occurs when controller
shows watering

a) Faulty wiring, solenoid, or valve

Check / Repair open wire, faulty
solenoid, or faulty valve

b) Water supply may be shut off Check water supply line has pressure

c) SHUTDOWN RAIN FORECAST

indicator is on

Check rain sensor jumper wire or rain
sensor (see page 20)

Controller does not water as
scheduled

a) AUTO RUN is OFF or in SKIP MODE Set AUTO RUN to ON
b) Current date and time is incorrect Check / Set current date and time

c) WATERING SCHEDULE not

programmed correctly

Verify WATERING DAYS option, START
TIMES, and CYCLES per day

d) Smart technology adjusted the

watering duration to zero

Normal Smart operation (see pages 1
and 16)

e) UNDOCKED indicator is on Fully dock the controller

24

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 24

The following information will be needed for each Zone

1) The number of watering CYCLES per day.

2) The number of minutes (DURATION) per CYCLE.

3) Start time (START) for each watering CYCLE.

The example below illustrates how a watering schedule is transferred into the programming aid.

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

20 MIN 4:00 A

2

30 MIN 6:00 P

3

4

2

FRONT LAWN

LOCATION:

0002

Odd / EvenSpecific Days of Week

2

Number of watering CYCLES per day

CYCLE

1

1

25

Programming Aid - Introduction

If watering on “Specific Days of Week”:

❶

ZONE 1:

❶ CYCLES (0, 1, 2, 3, or 4):

Water 2 times per day on Sunday, Tuesday, and Thursday
Water 1 time per day on Saturday

❷ DURATION:

Water 20 minutes on the first cycle (CYCLE 1)
Water 30 minutes on the second cycle (CYCLE 2)

❸ START:

Start first cycle (CYCLE 1) at 4:00 AM
Start second cycle (CYCLE 2) at 6:00 AM

❸

❷

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 25

26

CYCLES:

ODD or EVEN:

Programming Aid - Introduction

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

20 MIN 4:00 A

2

30 MIN 6:00 P

3

4

2

LOCATION:

Specific Days of Week Odd / Even

FRONT LAWN

1

CYCLE

Number of watering CYCLES per day

❶

If watering on “Odd/Even Dates of Month”:

ZONE 1:

❶ CYCLES (0, 1, 2, 3, or 4):

Water 2 times per day on EVEN, dates of the month

❷ DURATION:

Water 20 minutes on the first cycle (CYCLE 1)
Water 30 minutes on the second cycle (CYCLE 2)

❸ START:

Start first cycle (CYCLE 1) at 4:00 AM
Start second cycle (CYCLE 2) at 6:00 AM

❸❷

0 indicates no starts (no watering)
1-4 indicates number of start times per watering day.

ODD will water on 1st, 3rd, 5th, etc. dates of month
EVEN will water on 2nd, 4th, 6th, etc. dates of month

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 26

Programming Note

• The watering schedule reservation system adds a 5 minute buffer (no watering) at the end of each DURATION.

• In the example below for ZONE-1 / CYCLE-1; the DURATION = 20 minutes and START = 4:00 AM.
– The next available START time is: (4:00 AM + 20 min. + 5 min.) = 4:25 AM.
– This next available START time is used for ZONE-2 / CYCLE-1.
– This was repeated for ZONE-3 / CYCLE-1. Based on ZONE-2 / CYCLE-1 START time and DURATION, the

next available START time is: (4:25 AM + 45 min. + 5 min.) = 5:15 AM .

Programming Aid - Example

watch the video at raindrip.com/smart

27

Option 1 Example - WATER ON SPECIFIC DAYS OF WEEK

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

20 MIN 4:00 A

2

30 MIN 6:00 P

3

4

1

45 MIN 4:25 A

2

60 MIN 6:35 P

3

4

1

10 MIN 5:15 A

2

10 MIN 10:00 A

3

10 MIN 7:40 P

4

10 MIN 10:00 P

2

02020

LOCATION:

BACK LAWN

2

FRONT LAWN

LOCATION:

4040

LOCATION:

4

3

00

FLOWER BEDS

0

20

002

Odd / EvenSpecific Days of Week

2

Number of watering CYCLES per day

CYCLE

1

1

❸

❷

❶

❶

❷

❸

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 27

watch the video at raindrip.com/smart

28

Option 2 Example - WATER ON ODD / EVEN DATES OF MONTH

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

20 MIN 4:00 A

2

30 MIN 6:00 P

3

4

1

45 MIN 4:25 A

2

60 MIN 6:35 P

3

4

1

10 MIN 5:15 A

2

10 MIN 10:00 A

3

10 MIN 7:40 P

4

10 MIN 10:00 P

4

LOCATION:

2

BACK LAWN

3

2

LOCATION:

2

LOCATION:

FLOWER BEDS

Specific Days of Week Odd / Even

FRONT LAWN

1

CYCLE

Number of watering CYCLES per day

CYCLE

❶

❷

❸

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 28

Programming Aid - Worksheet

29

Number of watering CYCLES per day

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

2

3

4

1

2

3

4

1

2

3

4

LOCATION:

LOCATION:

3

LOCATION:

2

Odd / EvenSpecific Days of Week

1

CYCLE

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 29

Programming Aid - Worksheet

30

Number of watering CYCLES per day

ZONE SU MO TU WE TH FR SA ODD EVEN DURATION START

1

2

3

4

1

2

3

4

1

2

3

4

LOCATION:

LOCATION:

6

5

LOCATION:

4

Specific Days of Week Odd / Even

CYCLE

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 30

watch the video at raindrip.com/smart

www.raindrip.com

31

A/C Power Supply

Input: 120VAC, 60 HZ
Output: 24VAC, 0.45amps
Controller Zone Output: 24VAC, 0.25amps

Battery Power

Two (2) "AA" alkaline (not included).
Depending on battery usage, batteries should be replaced once a year.
(do not use lithium or rechargeable batteries)

Operating Temperature Range

Storage: 0˚ F to 140˚ F
Operating: 30˚ F to 130˚ F

Specifications

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 31

Warranty

Raindrip Smart Controller - Limited Warranty

watch the video at raindrip.com/smart

www.raindrip.com

Raindrip warrants to the original product or service purchaser ('the Customer') that the Raindrip product, for which the Customer
received this warranty, was designed, developed and/or fabricated using all due reasonable commercial care and good
manufacturing practices. Raindrip's product shall be free from defects in material and workmanship for one year, from the original
date of purchase. Raindrip's sole and exclusive obligation under this warranty is to provide for the free repair or replacement of the
product or of defective part in the product, at Raindrip's option.

Warranty Limitations. The duration of any implied warranty or condition, of merchantability, fitness for a particular purpose, or
otherwise, on this product shall be limited to the duration of the express warranty set forth above. In no event shall Raindrip be
liable for any loss, inconvenience or damage, whether direct, incidental, consequential or otherwise, resulting from breach of any
express or implied warranty or condition, of merchantability, fitness for a particular purpose or otherwise with respect to this
product, except as set forth herein. Some states or countries do not allow limitation on how long an implied warranty lasts and
some do not allow exclusions or limitations of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. This warranty will be interpreted pursuant to the laws of the United States and the State of California. The original
English language version (meaning) of this warranty controls over all translations.

Warranty Service Options. For service under this warranty you must return the product to the store where you purchased [the units] it.

Warranty Exclusions.

This warranty does not cover the following:

• Products that have been modified, neglected or poorly maintained, misused, abused or involved in accidents or natural disasters.

• Damage to the product resulting from improper maintenance or repair, the use or installation of parts and/or accessories that are
not compatible with the original intended use of the product, or the failure to follow the product warnings and usage instructions.

• Damage or deterioration to the surface finish, aesthetics or appearance of the product.

• The labor costs required to remove and/or refit and readjust the product covered by this warranty.

• Normal wear and tear to the product.

• Product installed outdoors or in a manner not recommended by Raindrip.

• Or, any products for which the Customer does not follow the warranty procedures outlined [above] in this Limited Warranty.

 877.502.7952
 [e-mail]
 raindrip.com/smart

32

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 32

 877.502.7952

 [e-mail]
 raindrip.com/smart

Monday - Friday 8:00 AM - 5:00 PM (Pacific Standard Time)
Saturday - Sunday 9:00 AM - 1:00 PM (Pacific Standard Time)

RSC INSTG-A

SmrtCntrl_InstlltnPrgrmng_Bklt 3/31/09 4:57 PM Page 33