
1
Standard ICs
Dual high slew rate operational
amplifier
BA4510F / BA4510FV
The BA4510F and BA4510FV are monolithic ICs that contain two operational amplifiers with high slew rate, featuring
phase compensation. These ICs can be driven with a low-voltage power supply, requiring a power supply range of
± 1 to ± 3.5V for a dual power supply and 2 to 7V for a single power supply. In addition, an unbuffered type is used
which enables ample output even in low voltage ranges, enabling swing at up to nearly the power supply voltage.
•
Block diagram
+
+
1
2
3
4
8
7
6
5
OUT1
– IN1
+ IN1
V
EE
VCC
OUT2
– IN2
+ IN2
1ch
2ch
–
–
•
Features
1) Low-voltage operation.
2) High slew rate.
3) Wide dynamic output range.
4) Compact 8-pin SSOP-B package. (BA4510FV)

2
Standard ICs BA4510F / BA4510FV
•
Internal circuit configuration
VCC
VEE
R2
R3
A
R
1
Q7
Q1
– IN
+ IN
Q
2
OUT
R4
X3
X2
Q8
R5
Q9
•
Absolute maximum ratings (Ta = 25°C)
Parameter Symbol Limits Unit
Power supply voltage V
CC ± 5V
Power dissipation
BA4510F
BA4510FV
550
∗
1
(SOP)
350
∗
2
(SSOP)
mW
Differential input voltage V
ID ± VCC V
Common-mode input voltage V
I 0 ~ VCC V
Operating temperature Topr °C
Storage temperature Tstg °C
Pd
– 20 ~ + 75
– 40 ~ + 125
∗
1 If used at temperatures higher than 25°C, reduce power by 5.5mW for each 1°C above Ta = 25°C.
This value is the value measured when mounted on a glass epoxy board (50mm × 50mm × 1.6mm).
∗
2 If used at temperatures higher than 25°C, reduce power by 3.5mW for each 1°C above Ta = 25°C.
This value is the value measured when mounted on a glass epoxy board (70mm × 70mm × 1.6mm).
The value is 300mW when the IC is used alone.

3
Standard ICs BA4510F / BA4510FV
•
Electrical characteristics (unless otherwise noted, Ta = 25°C, VCC = ±2.5V)
Parameter Symbol Min. Typ. Max. Unit
Input offset voltage V
IO —1 6mVRS = 50Ω
Input offset current I
IO — 2 200 nA
Input bias current I
B — 80 500 nA
High-amplitude voltage gain A
V 60 90 — dB
Common-mode input voltage V
ICM – 1.3 — V
Common-mode rejection ratio CMRR 60 80 — dB
Power supply voltage rejection ratio PSRR 60 80 — dB R
S = 50Ω
Quiescent current I
Q 2.5 5.0 7.5 mA
Output voltage
High V
OH 2.0 2.4 — V RL = 2kΩ
Low V
OL — – 2.4 – 2.0 V RL = 2kΩ
Slew rate S.R. 5 V /
µs—
1.5
—
Conditions
R
L⭌2kΩ, VCC = 15V
R
L = ∞ALL AMPS
∗
1
∗
1 Because the first stage is configured with a PNP transistor, input bias current is from the IC.
•
Electrical characteristic curve
POWER DISSIPATION: Pd (mW)
AMBIENT TEMPERATURE: Ta (°C)
1200
1000
800
600
400
200
0
0 25 50 75 100 125 150
BA4510F
BA4510FV
Fig. 1 Power dissipation vs. ambient
temperature
•
Operation notes
(1) Unused circuit connections
If there are any circuits which are not being used, we
recommend making connections as shown in Figure 2,
with the non-inverted input pin connected to the potential within the in-phase input voltage range (V
ICM).
(2) If used with a voltage follower, be careful of oscillation which may cause problems with the in-line input
voltage range or the capacitance load.
(3) If using at power supply voltage + 5.0 or higher, be
sure the gain is reduced sufficiently to prevent oscillation.
VCC
VEE
To potential
in V
ICM
+
–
Fig. 2 Unused circuit connections

4
Standard ICs BA4510F / BA4510FV
•
External dimensions (Units: mm)
SOP8 SSOP-B8
BA4510F BA4510FV
0.4 ± 0.11.27
0.15
0.3Min.
0.15 ± 0.1
0.11
6.2 ± 0.3
4.4 ± 0.2
5.0 ± 0.2
85
41
1.5 ± 0.1
0.1
0.22 ± 0.1
0.65
0.3Min.
548
1
6.4 ± 0.3
4.4 ± 0.2
3.0 ± 0.2
1.15 ± 0.1
0.15 ± 0.1
0.1
(0.52)