Rain bird XCZ-LF-100-PRF User Manual

Replacement Parts

The PRF ﬁlter comes with a 200 mesh stainless steel ﬁlter installed.

RBY-200-SS-MX 200 mesh stainless steel ﬁlter element

Operation Range

Flow 0.2 to 5.0 gpm (0,8 to 18,9 L/m)

Inlet Pressure 20 to 120 psi (1,8 to 8,3 bar)

Outlet Pressure Regulated at 30 psi (2,1 bar)

Water Temperature 33°F (0,5°C) to 110°F (43°C)

Ambient Temperature 33°F (0,5°C) to 125°F (52°C)

Valve Voltage 24 VAC 50/60 Hz (cycles/sec)

Related Products

XFD-xx-xx-xxx XF Series Dripline

Available in 0.6 or 0.9 GPH at 12”, 18”, or 24” spacing.

Rain Bird Corporation

970 West Sierra Madre Avenue, Azusa, CA 91702, U.S.A. Phone: (626) 812-3400 Fax: (626) 812-3411

Rain Bird Corporation

6991 East Southpoint Road, Tucson, AZ , 85706, U.S.A. Phone: (520) 741-6100 Fax: (520) 7

Rain Bird International, Inc.

P.O. Box 37, Glendora, CA, 91740-0037, U.S.A. Phone: (

626) 963-9311 Fax: (626) 852-7343

41-6522

1” Low-Flow Control Zone Kit

with PR Filter

Model:

XCZ-LF-100-PRF

Installation and Operation

www.rainbird.com

The Intelligent Use of Wat

er™ -- Visit www.rainbird.com to learn about our eﬀorts

P/N 177630

Rev A

Assembly















�

1. Apply Teﬂon™ tape (1 ½ to 2 turns) to all male pipe threads. Do not use pipe thread or pipe dope compound.

2. Hand tighten components in the above conﬁguration, no more than 2 turns past ﬁnger tight. Make sure the ﬂow arrow on the ﬁlter in in the correct orientation. a. Low Flow Valve - 1” female NPT to 1” female NPT b. Reducer bushing - 1” male NPT to 3/4” female NPT c. Pressure-Regulating Filter (PRF) - 3/4” male NPT x 3/4” male NPT d. Multi-diameter Fitting (MDF) - 3/4” female NPT to poly tubing

Installation

5. Unscrew the cap of the Pressure-Regulating Filter and remove the ﬁlter element.

6. Replace cap without ﬁlter element.

7. Activate ﬂow through the valve the valve either manually or using the controller. To Manually activate, turn the solenoid handle counter-clockwise ½ to ¾ turns.

8. Run water several minutes to ﬂush the system.

9. Replace the ﬁlter element.

10. Prepare poly tubing 16mm to 18mm OD by cutting the tubing at least 1½” away from any emitter.

11. Check to see that the cut is clean and the tubing is not deformed (out of round).

12. Insert the tubing end into the Multi-Diameter Fitting, centering the tube on the white insert of the ﬁtting. The tube should slide freely into the ﬁtting for approximately ½” before meeting resistance.

13. After initial resistance, continue to insert the tube an additional ¾” until the tube reaches a full stop.

1. Install the Low Flow Valve on the water supply line.

2. Orient the Pressure-Regulating Filter down to prevent debris entering the line when the ﬁlter is removed for cleaning.

3. Do not install tubing or other downstream elements yet.

4. Connect one solenoid wire to the controller common and the other wire to the controller power. User only water-tight connectors, such as Rain Bird ST-03.

Note: Multi-diameter ﬁttings cannot be reused.

Operation / Maintenance

1. Periodically remove the ﬁlter element.

2. If dirty, rinse the ﬁlter element in water before reinstalling.

Winterization

In a freezing climate, water should be removed from the irrigation system before freezing occurs. For more information, please refer to Rain Bird’s Winterization Guide, available at www.rainbird.com.

Technical Assistance

Internet: www.rainbird.com Toll Free: 800-247-3782

Thank you for using our products.