Raidon InTANK iR2623-S3 User Manual
iR2623-S3
User Manual
InTANK
» InTANK iR2623-S3 User Manual ..............................................................1
» InTANK iR2623-S3 產品使用說明 ...........................................................12
iR2623-S3 User Manual
V1.
1
iR2623-S3 User Manual
1
Table of Contents
1. Package Contents and Product Views
Introduction
Thank you for purchasing RAIDON products. This manual will introduce the IR2623-S3 Series.
Before using your IR2623-S3, please read this manual thoroughly. Although all information contained
in this user manual has been carefully veried before publishing, however, the actual product
specication will be based on the time of delivery from RAIDON. Any updates to the product
specications or relevant information may be found on www.raidon.com.tw. Products are subject
to change without prior notications.
If you have any questions regarding the products of RAIDON, or you would like to know the latest
product information, user manual update, or rmware update, please contact your local supplier or
visit www.raidon.com.tw for further information.
Copyright © RAIDON TECHNOLOGY, INC. All rights reserved.
Open the package and you should nd the following:
Please make sure that the contents listed above are not damaged or missing. If you should find
damages or missing contents, please contact your supplier immediately.
1. Package Contents and Product Views
2. Operating Information
3. Hardware Requirements and Precautions
4. Hardware Installation Procedure
5. Setting RAID Mode
6. Computer Set Up
7. Hard Disk status on LCD screen
8. Data Rebuilding Operation
9. GUI Monitoring Software and Firmware Update GUI
10. Frequently Asked Questions
IR2623-S3
IR2623-S3 x 1
( with removable drive tray enclosed )
Internal RS232 Cable x 1
External RS232 Cable x 1
SATA Cable x 1
CD x 1
Screws and key x 3
Quick Setup Guide x 1
» InTANK iR2623-S3 User Manual
iR2623-S3 User Manual
2
Front View
LED Indicators :
1. 2.5" HDD status indicator LED
2. 2.5" HDD tray ejector opening
3. 2.5" HDD tray ejector handle
4. LCD Display
5. LED of failure Alarm
6. Pri HDD status indicator
7. Sec HDD status indicator
8. Mute Button
9. 3.5" Removable drive tray
10. HDD tray ejector opening
11. Pri HDD tray access light
12. Sec HDD tray access light
13. Cooling fan
14. RAID mode switch
15. RS232 Port
16. 3.5" SATA Port
17. 15 PIN SATA Port
18. 4Pin Power socket
19. 2.5" SATA Port
Status
Panel light 3.5" HDD tray access light
2.5"
HDD tray
access light
Buzzer
Fail LED
Pri HDD
status indicator
Sec HDD
status indicator
Pri HDD tray
access light
Sec HDD tray
access light
Power On — —
Orange light
always on
Blue and Purple light ashing
Blue light
always on
— —
Stabdby — —
Orange light
always on
Blue light
always on
Blue light
always on
— —
HDD
Failure
Red light
always on
— —
Red light
always on
Blue light
always on
On
Access — —
Orange light
always on
Blue and Purple light ashing
Blue light
ashing
— —
Rebuilding
(Source)
— —
Orange light
always on
Blue light
always on
Blue light
always on
— —
Rebuilding
(Target)
— — — —
Red light
ashing
Blue light
always on
— —
Fan Failure
Red light
always on
Orange light
always on
Blue light
always on
Blue light
always on
On
Over Heat
（
≥50℃)
Red light
always on
Orange light
always on
Blue light
always on
Blue light
always on
On
iR2623-S3 User Manual
3
2. Operating Information
3. Hardware Requirements and Precautions
4. Hardware Installation Procedure
Operating Temperature : 0 ~ 40 °C (32 ~ 104 °F)
Storage Temperature : -10 ~ 70 °C (14 ~ 158 °F)
Line Voltage : 5V DC
1. Computers or servers with SATA I & SATA II & SATA III.
2. Hard drive with SATA I & SATA II & SATA III
3. You are strongly advised to set the storage mode (the default is the Independent mode) before
using the IR2623-S3.
4. The product allows the user to simultaneously utilize two hard drives manufactured by dierent
companies. However, if the user expects better eciency, we strongly recommend the users to
use hard drives manufactured by the same manufacturer.
5. Please make sure that the two hard drives are free from bad blocks or defects prior to installation
in order to avoid system crashes or data loss.
6. The actual storage capacity of IR2623-S3 recognized by the system may differ from the total
capacity stated on the hard drives combined once the drives have been formatted.
7. It is highly recommended for users to back up important data contained within the IR2623-S3
unit on a regular basis or whenever the user feels necessary to a remote or a separate storage
device. Stardom will not be responsible for any lost of data caused during the use of the unit or
the recovery of the data lost.
Please follow the instructions below to complete the hardware installation.
Open the package and take out the product making sure that all the enclosed contents are
not damaged or missing. Should you nd damages or missing contents, please contact your
supplier immediately.
Place the system on a stable surface. Ensure that it is well ventilated without blockage to
the vent and kept away from areas near water and damage prone areas.
Use the key included in the accessory kit and inserted into the key access opening to eject
the removable drive tray latch and extract the removable drive tray.
Mount your hard drives onto the removable drive tray and secure it with the screws included
in the accessory kit to avoid any damage to the hard drive due to accidental movements.
When the hard drive installation has been completed, insert the hard drive tray into the
system horizontally and secure the latch into place.
Use the preferred cable included to connect your computer to the relative interface
connection on the IR2623-S3 unit.
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Note :
Once the drive mode conguration has been completed, re-conguration using the same hard
drives to set the drive mode will result in complete data loss. If you must change the drive
mode, make sure to backup all data prior to the mode change.
iR2623-S3 User Manual
4
SATA
SATA
45cm SATA Cable
Power Supply Connector
Internal Case
Internal RS232 Cable
External RS232 Cable
1
2
3
4
PD3500+
COM1
COM2
1
2
3
4
※
Note :
1. RS232 Port and RS232 Cable: Provides hardware status monitoring to industrial control system or IPC via RS232.
2. We do not recommend users to disassemble the device without proper instructions and authorization. The manufacture warranty
will not cover the damages caused by unauthorized disassembling.
3. To prevent the device from malfunction, please make sure the device is connected with a direct and dedicated power connection of
a stable power input.
5. Setting the Hard Drive Array Mode
Please select the RAID mode with the jumper located at the back panel. The original default is RAID
1, still there are three pins at the back panel for RAID mode selection: RAID 0 mode by setting the
jumper on the bottom of the two pins. RAID 1 mode by setting the jumper on the top of the two pins.
1. RAID 1 Mode
1). Place two new hard drives into IR2623-S3 and strongly suggest you to use two identical hard
drives to get the equal capacity. If the capacity is dierent, IR2623-S3 is downward to the small
hard drive capacity.
2). Under RAID 1 mode, two hard drives has the identical information as one to mirror to the other
one, therefore each of the hard drive failed is still able to function normally. When you replace
the failed hard disk to the new one the system automatically rebuilding the data to the newly
place hard disk.
2. RAID 0 Mode
1). Place two new hard drives into IR2623-S3 and strongly suggest you to use two identical hard
drives to get the equal capacity. If the capacity is dierent, IR2623-S3 is downward to the small
hard drive capacity.
2). Under RAID 0 mode, capacity is add up to a one big volume, also with the feature of faster
read/write performance ecient.
iR2623-S3
iR2623-S3 User Manual
5
6. Computer Set Up
When the hardware setup for IR2623-S3 is complete, you are now ready to turn the machine on.
After the hardware installation is complete, the IR2623-S3 will be treated as one single hard drive.
Set the hard drive to AUTO in the computer’s BIOS. When the computer is turned on, the system will
retrieve the following information:
1. In IR2623-S3, the installed hard drive can be detected by the Device Manager of Computer
Management for Windows.
2. Customers can choose to format the hard drive by using the Disk Management tool of the
operating system before using the IR2623-S3.
At this point, the installation process is completely nished. The user can freely retrieve and save
data to IR2623-S3 just like retrieving and saving data to a regular hard drive. If the user experiences
any abnormality during the operation, please refer to the trouble shooting Q&A section in Appendix.
iR2623-S3 User Manual
6
7. Hard Disk status on LCD screen
2. Over Temperature (≥50°C)
Pri HDD : OK
Sec HDD : OK T
3. Fan Failure.
Pri HDD : OK F
Sec HDD : OK
4. RAID 1 Degraded. Primary hard drive is failure, but secondary hard drive is normal.
RAID-1 degraded
Pri : X Sec : O
5. RAID 1 Failure. Primary and secondary hard drives are failure.
RAID-1 failure
Pri : X Sec : X
6. RAID 1 Failure. (Double Source)
RAID-1 failure
Double Source
7. RAID 0 Failure. Primary hard drive is missing, but secondary hard drive is normal.
RAID-0 failure
Pri : M Sec :O
8. Rebuilding
Rebuilding
Sec→Pri 32%
1. Booting and Normal status.
IR2623
RAID-1 vxxxxxx.x
Pri HDD : OK
Sec HDD : OK
Loading...