The CTR BT 01 Bluetooth interfaces with Raffel Systems power recline controls. It
allows full connectivity to the end user to control functions of a power recline chair
using a variety of Bluetooth enabled devices such as cell phones, tablets, and
laptops.
Feature Controls:
Power Head Rest, Lumbar, Recline, and Home
position
Memory One – User 1
System of Components:
Operation:
The app to be used with Raffel Systems BLE enabled devices can be downloaded
from both iTunes and Google Play stores. The app is titled “Raffel Seat” and can be
seen in Figure 2-1 below:
Raffel Systems ~ N112W14600 Mequon Rd ~ Germantown, WI 53022 ~ (262)502-1011~ (262)502-1010
Figure 2-1: “Raffel Seat” app by Raffel Systems, LLC.
This app can be downloaded to any BLE enabled device i.e. cell phones, tablets,
and laptops.
To begin operation, enable Bluetooth functionality on your device, then open the
“Raffel Seat” app shown in Figure 2-1.
Select the desired device to control from the dropdown menu shown in Figure 3-1
below:
Figure 3-1: List of available BLE-enabled devices.
Once you have selected your device and are connected, you will see a screen titled
“Recline.” This screen is used to control the power motion actuators of the chair.
Depending on the Raffel product connected, you will see either a mix or all of the
Raffel motion functions including Power Recline, Headrest, Lumbar, Home, Memory
User 1 and Memory User 2. A more complete description of functionality can be seen
as follows:
Raffel Systems ~ N112W14600 Mequon Rd ~ Germantown, WI 53022 ~ (262)502-1011~ (262)502-1010
Depress the desired icon for Head Rest, Lumbar,
and Recline to either open or close to the desired
position and release to stop.
Home icon
The purpose of the Home icon is to fully reposition
the Head Rest, Lumbar, and the Recliner to the
fully seated position.
Depress and hold the Home icon to reposition the
chair until fully seated position. Release icon to
stop at any time.
Set Memory 1 Position
Depress the Open and or Close icon to the
desired position for user 1 for all three functions
i.e. Head Rest, Lumbar, and Recline. Then
depress and release the Set icon for Memory 1.
Chair movement will indicate that Memory 1 has
been set.
Press and hold the Home Icon until the chair is in
the fully seated position. Depress the Memory 1
Go icon and the chair will reposition to the set
Memory 1 position automatically.
Disconnect
Depress the X in the upper left hand of the screen to disconnect control to the chair;
upon disconnect, the user will be taken to the screen showing a list of available
devices (shown in Figure 3-1.
Raffel Systems ~ N112W14600 Mequon Rd ~ Germantown, WI 53022 ~ (262)502-1011~ (262)502-1010
This equipment has been tested and found to comply with the limits for Part 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (2) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
To comply with FCC RF exposure limits for general population/uncontrolled exposure,
the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
To comply with ISED RF exposure limits for general population/uncontrolled exposure,
the antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
This Device complies with Industry Canada License-exempt RSS Standard(s).
Operation is subject to the following two conditions: 1) this device may not cause
interference, and 2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Note: Modifications to this product will void the user’s authority to operate this
equipment.
Raffel Systems ~ N112W14600 Mequon Rd ~ Germantown, WI 53022 ~ (262)502-1011~ (262)502-1010
Raffel Systems, LLC warrants this product (including any accessories) against defects in
material and workmanship for a period of 12 months from the date of the first consumer
purchase. This warranty is enforceable only by the original purchaser only. ALL DAMAGED OR
MISSING PARTS MUST BE REPORTED WITHIN 14 DAYS OF PURCHASE.
This warranty covers all defects in material and workmanship in this product, but DOES NOT COVER the following.
1. Damage, deterioration or malfunction resulting from:
Acts of God, accident, misuse, abuse, negligence, improper installation,
maintenance, improper operation, or failure to follow the instructions contained in
this Owner’s Manual.
Any damage in the shipment of the products.(Claims must be presented to the
carrier) Repair, attempted repair, or modifications done by anyone other than Raffel
System technicians.
Any unit which has been modified of attempted to be modified or altered in anyway
whatsoever.
2. Normal wear and periodic maintenance.
3. Any unit used for industrial or commercial purposes (including rental).
4. Products sold AS IS or WITH ALL FAULTS, or consumables (such as fuses, batteries,
etc).
5. Customer instruction installation and set up adjustments or signal reception problems.
6. Raffel Systems, LLC will repair or replace (at it's discretion) the units covered by this
warranty, without charge to the consumer for labor or materials.
CUSTOMERS ARE RESPONSIBLE:
FOR INITIAL SHIPPING CHARGES. However, Raffel Systems will pay the return shipping
charges to any destination within the USA if repairs are covered by the warranty.
TO OBTAN WARRANTY SERVICE, please call Raffel Systems Service Center.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE CONSUMER. RAFFEL SYSTEMS SHALL NOT BE
LIABEL FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF
ANY EXPRESSED OR IMPLIED WARRANTY ON THIS PRODUCT.EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTIES,INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE LENGTH OF THIS
WARRANTY.
Raffel Systems ~ N112W14600 Mequon Rd ~ Germantown, WI 53022 ~ (262)502-1011~ (262)502-1010