Page 1
AP0127450, AP0127460
RF Module Operating in the 2.4 GHz bands
REFERENCE GUIDE
Page 2
Warning
Avertissement
Regulatory Compliance
FCC/IC - Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules and IC RSS standards. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
the receiver is connected.
It is the responsibility of the installer to ensure that when using the outdoor
antenna kits, only those antennas certified with the product are used. The use
of any antenna other than those certified with the product is expressly
forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards.
Il est de la responsabilité de l'installateur de s'assurer que lorsque vous
utilisez les kits d'antennes extérieures, seules les antennes certifiés avec le
produit sont utilisés. L'utilisation d'une antenne autre que ceux qui sont
certifiés avec le produit est expressément interdite par la réglementation FCC
partie 47 CFR 15.204 et IC normes RSS.
AP0127450, AP0127460 Reference Guide i
Outdoor units and antennas should be installed ONLY by experienced
installation professionals who are familiar with local building and safety codes
and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void the product warranty and
may expose the end user or the service provider to legal and financial
Caution liabilities. Resellers or distributors of this equipment are not liable for injury,
damage or violation of regulations associated with the installation of outdoor
units or antennas. The installer should configure the output power level of
antennas according to country regulations and antenna type.
Page 3
This equipment should be installed and operated with a minimum distance of
354cm between
the radiator and your body.
Warning
The module is granted to operate under FCC certification in the 2.4 GHz
band only.
Warning
Prudence
Avertissement
Les unités extérieures et les antennes doivent être installés que par des
professionnels expérimentés d'installation qui sont familiers avec les normes
locales et les codes de sécurité et, si applicable, sont agréées par les autorités
gouvernementales de réglementation compétents. Ne pas le faire peut annuler
la garantie du produit et peuvent exposer l'utilisateur final ou le fournisseur de
services d'obligations juridiques et financiers.
Revendeurs ou distributeurs de ces équipements ne sont pas responsables des
blessures, des dommages ou violation des règlements liés à l'installation des
unités extérieures ou des antennes. L'installateur doit configurer le niveau de
puissance de sortie des antennes conformément aux réglementations
nationales et le type d'antenne.
Cet équipement doit être installé et utilisé à une distance minimale de 354cm
entre le radiateur et votre corps.
This device complies with Part 15 of the FCC rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Cet appareil est conforme la norme d'Industrie Canada exempts de licence RSS (s). Son
fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas causer d'interférences, et
2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent
causer un mauvais fonctionnement de l'appareil.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada
AP0127450, AP0127460 Reference Guide ii
Page 4
Overview
The AP0127450, AP0127460 is an RF module operating in the 2.4 GHz frequency band. It is
a TDD OFDM radio supporting 802.11b/g/HT20/HT40 WiFi operating modes and 5 MHz, 10
MHz, 20 MHz and 40 MHz channel bandwidths based on 802.11n. The RF module can
support 2x2 and 3x3 radio chains.
The RF module cannot work as a stand-alone device. It can operate and be controlled only
when attached to a digital main board and altogether assembled in an enclosure suitable for
outdoor use. The assembly of the RF module attached to the digital main board is hereafter
referred to as ‘ODU’. The ODU in its various outdoor enclosures is manufactured by
RADWIN.
The RF module is certified as a limited modular approval type with the FCC ID:
Q3KRW24MOD and IC: 5100A-RW24MOD.
Condition of Use
The AP0127450, AP0127460 RF module is a proprietary radio interface and can only be
connected to digital boards manufactured by RADWIN. The ODU resides in an outdoor
enclosure also manufactured and assembled by RADWIN or its subcontractors. The RF
module is not for sale to the general public.
FCC rules and IC Regulation Restrictions
The ODU firmware is factory programmed to operate under the FCC rules and Industry
Canada regulation restrictions. The firmware is locked and inaccessible by any third party.
As a result of the above the user interface allows both the installer and the user to control
the ODU only within the boundaries of the regional restrictions.
Antennas
The AP0127450, AP0127460 RF module is certified with various antenna types covering both
Point-to-Point and Point-to-Multipoint systems. There are Omni type antennas and dual pole
cross polarized antennas. These antennas are the only ones to be used with the RF module.
AP0127450, AP0127460 Reference Guide 1
Page 5
Certified Antennas
Antenna Type
Manufacturer
Model Number
Antenna Max
Gain (dBi)
Flat Panel Dual Pole Cross Polarized
External
RADWIN Ltd.
RW-9612-2427
20
Flat Panel Dual Pole Cross Polarized
Integrated
RADWIN Ltd.
MT0073320
17.5
Sector Dual Pole Cross Polarized 80
Deg
RADWIN Ltd.
RW-9462-0827
9
Omni Directional Antenna
RADWIN Ltd.
MT0129070
8
Omni Directional Antenna
RADWIN Ltd.
RW-9463-0825
6.3
Omni Directional Antenna
RADWIN Ltd.
RW-9461-0827
4
Channel BW
(MHz)
Total Power @
2x2 (dBm)
Total Power @
3x3 (dBm)
5
29.62
N/A
10
29.58
N/A
20
29.73
29.31
40
29.18
29.29
Following is the list of antennas certified for use with the AP0127450, AP0127460 RF
module:
Maximum Output Power
The maximum output power can be set as follows, when operating in the 2.4 GHz band,
under FCC and IC regulations. The power values are for systems with 0 to 6 dBi total
antenna assembly gain. The total EIRP is limited to 36 dBm. Therefore the output power of
these systems, using higher than 6 dBi total antenna assembly gains will be reduced to
comply with 36 dBm EIRP. The following values are specified for 2x2 and 3x3 radio chains.
AP0127450, AP0127460 Reference Guide 2
Loading...