AP0158770
5 GHz Wireless Module
REFERENCE GUIDE
Regulatory Compliance
FCC/IC - Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules and IC RSS standards. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
It is the responsibility of the installer to ensure that when using the outdoor
antenna kits, only those antennas certified with the product are used. The use
of any antenna other than those certified with the product is expressly
forbidden by FCC rules 47 CFR part 15.204 and IC RSS standards.
Il est de la responsabilité de l'installateur de s'assurer que lorsque vous
utilisez les kits d'antennes extérieures, seules les antennes certifiés avec le
produit sont utilisés. L'utilisation d'une antenne autre que ceux qui sont
certifiés avec le produit est expressément interdite par la réglementation FCC
partie 47 CFR 15.204 et IC normes RSS.
Outdoor units and antennas should be installed ONLY by experienced
installation professionals who are familiar with local building and safety codes
and, wherever applicable, are licensed by the appropriate government
regulatory authorities. Failure to do so may void the product warranty and
may expose the end user or the service provider to legal and financial
Caution liabilities. Resellers or distributors of this equipment are not liable for injury,
damage or violation of regulations associated with the installation of outdoor
units or antennas. The installer should configure the output power level of
antennas according to country regulations and antenna type.
AP0158770 Reference Guide i
Warning
Avertissement
Les unités extérieures et les antennes doivent être installés que par des
professionnels expérimentés d'installation qui sont familiers avec les normes
locales et les codes de sécurité et, si applicable, sont agréées par les autorités
gouvernementales de réglementation compétents. Ne pas le faire peut annuler
la garantie du produit et peuvent exposer l'utilisateur final ou le fournisseur de
services d'obligations juridiques et financiers.
Revendeurs ou distributeurs de ces équipements ne sont pas responsables des
blessures, des dommages ou violation des règlements liés à l'installation des
unités extérieures ou des antennes. L'installateur doit configurer le niveau de
puissance de sortie des antennes conformément aux réglementations
nationales et le type d'antenne.
Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 314 cm from all persons and must not be colocated or operating in conjunction with another antenna or transmitter
within a device
Les antennes utilisées pour cet émetteur doivent être installées de manière à
fournir une distance de séparation d'au moins 314 cm par rapport à toutes les
personnes et ne doivent pas être co-localisées ou fonctionner conjointement
avec une autre antenne ou un autre émetteur dans un appareil
The module is granted to operate under FCC certification in the
4.9/5.1/5.3/5.4/5.8 GHz bands.
Warning
This device complies with Part 15 of the FCC rules and with Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Cet appareil est conforme la norme d’Industrie Canada exempts de licence RSS (s). Son
fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas causer d’interférences, et
2. Cet appareil doit accepter toute 3nterference, y compris les 3nterferences qui peuvent
causer un mauvais fonctionnement de l’appareil.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada
AP0158770 Reference Guide ii
Prudence
Avertissement
Overview
The AP0158770 is a wireless module operating in the 4.9, 5.1, 5.3, 5.4 and 5.8 GHz
frequency bands. It is a TDD OFDM radio supporting 5 MHz, 10 MHz, 20 MHz, 40 MHz and
80 MHz channel bandwidths.
The wireless module cannot work as a stand-alone device. It can operate and be controlled
only when attached to a digital main board and altogether assembled in an enclosure
suitable for outdoor use. The assembly of the wireless module attached to the digital main
board is hereafter referred to as ‘ODU’. The ODU in its various outdoor enclosures is
manufactured by RADWIN.
The wireless module is certified as a limited modular approval type under the FCC ID: Q3K5XACMOLD. It is also certified under IC: 5100A-5XACMOD.
Condition of Use
The AP0158770 wireless module is a proprietary radio interface and can only be connected
to digital boards manufactured by RADWIN. The ODU resides in an outdoor enclosure also
manufactured and assembled by RADWIN or its subcontractors. The wireless module is not
for sale to the general public.
FCC rules and IC Regulation Restrictions
The ODU firmware is factory programmed to operate under the FCC rules and Industry
Canada regulation restrictions. The firmware is locked and inaccessible by any third party.
As a result of the above the user interface allows both the installer and the user to control
the ODU only within the boundaries of the regional restrictions.
Antennas
The AP0158770 wireless module is certified with a wide range of antenna types covering
both Point-to-Point and Point-to-Multipoint systems up to 32 dBi gain.
AP0158770 Reference Guide 1
Antennas
Following is the list of antennas supported by the AP0158770 5 GHz Wireless Module:
Antenna Type
Manufacturer
Model Number
Antenna Max
Gain (dBi)
Sector Dual Pole Integrated 120 Deg
RADWIN Ltd.
MT0128930
11
Sector Dual Pole 120 Deg
RADWIN Ltd.
RW-9061-5004
11
Sector Dual Pole Integrated 95 Deg
RADWIN Ltd.
AM0135060
12
Sector Dual Pole 90 Deg
RADWIN Ltd.
RW-9061-5001
14
Sector Dual Pole 60 Deg
RADWIN Ltd.
RW-9061-5002
16.5
Sector Dual Pole Integrated 90 Deg
RADWIN Ltd.
MT0125250
13
Flat Panel Dual Pole Integrated
RADWIN Ltd.
AM0119960
16
Flat Panel Dual Pole Integrated
RADWIN Ltd.
AM0111760
16.5
Flat Panel Dual Pole Integrated
RADWIN Ltd.
MT0070760
24
Flat Panel Dual Pole External
RADWIN Ltd.
RW-9612-5001
23
Flat Panel Dual Pole External
RADWIN Ltd.
RW-9622-5001
29
Dual Pole Dish
RADWIN Ltd.
RW-9721-5158
29
Dual Pole Dish
RADWIN Ltd.
RW-9732-4958*
32
Shark Fin Monopole
RADWIN Ltd.
RW-9401-5002
12.5
Smart Antenna Multi Pole Integrated
RADWIN Ltd.
AM0156430
20.5
* Not applicable for 4.9 GHz band
Maximum Output Power
5725 – 5850 MHz band - FCC/IC
The maximum output power can be set as follows, when operating in the 5.8 GHz band,
under FCC and IC regulations. The power values are for PtP systems and PtMP systems with
0 to 6 dBi total antenna assembly gain. For PtMP systems the total EIRP is limited to 36
dBm. Therefore the output power for these systems, using higher than 6 dBi total antenna
assembly gains will be reduced to comply with 36 dBm EIRP.
The highest conducted output power shall be limited to 30 dBm in all channel bandwidths
5150 – 5250 MHz band – FCC
The maximum output power can be set as follows when transmitting in the 5.1 GHz band,
under FCC regulations.
The total EIRP limit for PtP applications is 53 dBm.
The total EIRP limit for PtMP applications is 36 dBm.
The total EIRP limit for PtMP applications when transmitting at elevations above 30° relative
to the horizon is 21 dBm.
5 MHz: 25.0 dBm
10 MHz: 27.0 dBm
20 MHz: 27.0 dBm
40 MHz: 27.0 dBm
80 MHz: 29.0 dBm
AP0158770 Reference Guide 2
5250 – 5350 MHz band – FCC/IC
The maximum output power can be set as follows, when operating in the 5.3 GHz band. The
total EIRP limit is 30 dBm.
5 MHz: 14.0 dBm
10 MHz: 16.0 dBm
20 MHz: 19.0 dBm
40 MHz: 19.0 dBm
80 MHz: 19.0 dBm
5470 – 5725 MHz band – FCC/IC*
The maximum output power can be set as follows, when operating in the 5.3 GHz band. The
total EIRP limit is 30 dBm.
5 MHz: 14.0 dBm
10 MHz: 17.0 dBm
20 MHz: 19.0 dBm
40 MHz: 19.0 dBm
80 MHz: 19.0 dBm
4940 – 4990 MHz band - FCC/IC
The maximum output power can be set as follows, when operating in the 4.9 GHz band,
under FCC and IC. The power values shown below are for systems using 0 to 26 dBi total
antenna assembly gain. Systems using 29 dBi antenna gain must reduce output power by 3
dB.
5 MHz: 26.97 dBm
10 MHz: 27.41 dBm
20 MHz: 28.24 dBm
Radio parameters accessed by end-user
The following parameters can be accessed by user:
1. Output Power
2. Frequency channel
3. Channel bandwidth
4. Antenna gain in external antenna type device
*
Under IC regulations the 5600-5650 MHz band is excluded from operation
AP0158770 Reference Guide 3
Loading...