Radio Shack 63-1124 User Manual

6YQ"$GNN"9KTGNGUU"&QQT"%JKOG

63-1124

"+/2146#06"

#

If an icon appears at the end of a paragraph,
go to the box on that page with the
corresponding icon for pertinent information.

— Warning

Rý

.... — Caution

— Important

#

°°°°

±

— Hint

#

— Note

OWNER’S MANUAL — Please read before using this equipment.

Receiver

Slide ON/OFF to
ON so that when
BELL is pressed
on one of the
transmitters, a
door chime
sounds.

Thank you for purchasing the RadioShack
Two Bell Wireless Door Chime. It works as a
doorbell, a remote pager, or an alert. You
can add an optional external sensor to have
a chime that alerts you when someone
walks into a room. The wireless door
chime’s three-position channel switch
prevents other transmitters or radio devices
from sounding the chime.

Transmitter (two included)

Indicator — Lights
when BELL is

pressed.

BELL — Press
BELL to hear the
door chime.

.

"%#76+10"

• Use only fresh batteries of the required size
and type. Always remove old or weak
batteries. They can leak chemicals that
destroy electronic circuits

• Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.

.

/1706+0)"6*'"
4'%'+8'4

10"#"(.#6"574(#%'

Pull out the wire stand on the back of the
receiver and set it on a table or other flat
surface.

10"#"9#..

1. Drill one 3/16-inch diameter hole and
insert one of the supplied anchors.

2. Drive the supplied M3.5 screw into the
hole until the screw's head extends

1

/8 inch from the wall.

about

3. Align the keyhole slot on the bottom of
the receiver with the screw in the wall,
then slide it down to secure it.

/1706+0)"6*'"
64#05/+66'4

1. Remove the transmitter from the holder.

2. Use the holder as a template to mark
two screw holes on the wall.

3. Remove the holder from the mounting
surface and drill two
holes. Insert one of the supplied
anchors into each hole.

3

/16 inch diameter

4. Drive a screw through the holders.

5. The transmitter can be slid in and out of
the holder . To lock the transmitter in the
holder, fix it with a size M2.6 screw at
the bottom of the holder.

+056#..+0)"
$#66'4+'5"#0&"
5'.'%6+0)"%*#00'.5

The wireless door chime requires three AAA
size batteries in both transmitters and three
C size batteries in the receiver. For best
performance and longest life, we
recommend RadioShack alkaline batteries.

....

+0"6*'"64#05/+66'4

1. Slide the transmitter's battery
compartment door in the direction of the
arrow to remove it.

2. Use a small flat-blade screwdriver to
slide the switch inside the battery
compartment to the desired channel for
the transmitter.

2002 RadioShack Corporation.

©

RadioShack and RadioShack.com are trademarks

All Rights Reserved.

used by RadioShack Corporation.

"016'"±"

±

The transmitter’s channel setting must be the
same as the receiver setting. If the door chime
occasionally sounds without anyone pressing
BELL, this indicates that the channel settings
are different. Change the channel settings so
both the transmitter and the receiver match.

"016'"±"

±

•Press BELL until the indicator lights.
Otherwise, the receiver may not work
properly.

• If you don't want to be bothered by the door
chime, slide ON/OFF on the receiver to OFF.

Limited One-Year Warranty

This product is warranted by RadioShack against manufactur­ing defects in material and workmanship und er norm al use for
one (1) year from the date of purchase from RadioShack
company-owned stores and authorized RadioShack franchi­sees and dealers. EXCEPT AS PROVIDED HEREIN,
RadioShack MAKES NO EXPRESS WARRANTIES AND
ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE DURA­TION OF THE WRITTEN LIMITED WARRANTIES CON­TAINED HEREIN. EXCEPT AS PROVIDED HEREIN,
RadioShack SHALL HAVE NO LIABILITY OR RESPONSI­BILITY TO CUSTOMER OR ANY OTHER PERSON OR EN­TITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT
NOT LIMITED TO, ANY DAMAGES RESULTING FROM IN­CONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REV­ENUE, OR PROFIT OR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limit ation of incidental or
consequential damages, so the above limitations or exclu­sions may not apply to you.
In the event of a product d efect during the warranty perio d,
take the product and the RadioShack sales receipt as proof of
purchase date to any RadioShack store. RadioShack will, at
its option, unless otherwise provided by law: (a) correct the
defect by product repair without charge for part s and labor; (b)
replace the product with one of the same or similar design; or
(c) refund the purchase price. All repl aced par ts and produ cts,
and products on which a refund is made, beco me the pr operty
of RadioShack. New or reconditioned parts and products may
be used in the performance of warranty servic e. Repaired or
replaced parts and products are warranted for the remainder
of the original warranty period. You will be charged for repair
or replacement of the prod uct made after the expiration of the
warranty period.
This warranty does not cover: (a) damage or failure caused
by or attributable to acts of God, abuse, accident, misuse, im­proper or abnormal usage, fai lure to follow instructions, im­proper installation or maintenance, alteration, lightning or
other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Ser­vice Facility; (c) consumables such as fuses or batteries; (d)
cosmetic damage; (e) transportation, shipping or insurance
costs; or (f) costs of product removal, installation, set-up ser­vice adjustment or reinstallation.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,

Fort Worth, TX 76102

12/99

3. Install three AAA batteries as indicated
by the polarity symbols (+ and –)
marked inside.

4. Replace the compartment door.

5. Repeat Steps 1-4 for the other
transmitter. If the transmitter's LED
indicator dims, replace its batteries.

+0"6*'"4'%'+8'4

1. Slide the receiver's battery
compartment door in the direction of the
arrow to remove it.

2. There are two channel switches inside
the battery compartment —

. Slide the channel switches so

BELL 2

BELL 1

that they are on the same channel as
the transmitter.

±

3. Install three C size batteries as
indicated by the polarity symbols (+ and
–) marked inside the compartment.

4. Replace the compartment door. If the
receiver's LED flashes with a short
beep tone, replace its batteries.

12'4#6+10

1. Slide

ON/OFF

2. Press and hold down
1 transmitter. Transmit begins, the
indicator lights, and the receiver sounds
the door chime twice.

3. When
transmitter, it’s indicator lights and the
door chime sounds “Home sweet
home”.

75+0)"6*'"%*+/'"#5"#0"
'

064;"%*+/'

1. Connect the transmitter to a normally
open alarm sensor. You need 2­conductor wire (not supplied) to make
this connection.

2. Split the ends of the wire, then connect
the wire from the sensor's switch to the
screw holes on the back of the
transmitter, using the two supplied
machine screws. If the sensor you are
using has both normally open and
normally closed contacts, be sure to
connect to the sensor's normally open
contacts.

3. Slide

ON/OFF

on the receiver to ON.

BELL

±

is pressed on the BELL 2

BELL

on the receiver to ON.

on the BELL

and

6*'"(%%"9#065";17"
61"-019

This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the

. These limits are designed to provide

Rules

FCC

reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the
instructions, may cause harmful interfer ence
to radio communications.

However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:

• Reorient or relocate the receiving
antenna.

• Increase the separation betwee n the
equipment and receiver.

• Consult your local RadioShack store or
an experienced radio/TV technician for
help.

• If you cannot eliminate the interference,
the FCC requires that you stop using
your door chime.

Changes or modifications not expressly
approved by RadioShack may cause
interference and void the user’s authority to
operate the equipment.

This device complies with Part 15 of the

FCC Rules

. Operation is subject to the
following two conditions: (1) this device may
not cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.

52'%+(+%#6+105

Frequency ........................433.92 MHz ± 600KHz

Transmitter current consumption...............<10mA

Receiver current consumption...<2mA @ standby

< 130mA @ sound playing

Receiver battery low.......................... 2.4V

Receiver audio power...............> 80dBA @ 25cm

Transmitter operating

temperature..................................–20

(–4

Specifications are typical; individual units might
vary. Specifications are subject to change without
notice.

± 0.1V

°C to 60 °C

°F to 140°F)

RadioShack Corporation
Fort Worth, Texas 76102

63-1124

AO0114AAA1

07A02

Printed in China