5KPING"$GNN"9KTGNGUU"&QQT"%JKOG
63-1123
"+/2146#06"
#
If an icon appears at the end of a paragraph,
go to the box on that page with the
corresponding icon for pertinent information.
— Warning
Rý
.... — Caution
— Important
#
°°°°
±
— Hint
#
— Note
OWNER’S MANUAL — Please read before using this equipment.
Receiver
Slide ON/OFF to ON
so that when BELL
is pressed on the
transmitter, a door
chime sounds.
Thank you for purchasing the RadioShack
Single Bell Wireless Door Chime. It works as
a doorbell, remote pager, or alert. You can
add an optional external sensor to have a
chime that alerts you when someone walks
into a room. The door chime’s three-position
channel switch prevents other transmitters
or radio devices from sounding the chime.
Transmitter
Indicator — Lights wh en
BELL is pressed.
BELL — Press BELL
to hear the door
chime.
.
.
"%#76+10"
"%#76+10"
• Use only fresh batteries of the required size
• Use only fresh batteries of the required size
and type. Always remove old or weak
and type. Always remove old or weak
batteries. They can leak chemicals that
batteries. They can leak chemicals that
destroy electronic circuits
destroy electronic circuits
• Do not mix old and new batteries, different
• Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
rechargeable), or rechargeable batteries of
different capacities.
different capacities.
.
.
/1706+0)"6*'"
4'%'+8'4
10"#"(.#6"574(#%'
Pull out the wire stand on the back of the
receiver and set it on a table or other flat
surface.
10"#"9#..
1. Drill one 3/16-inch diameter hole and
insert one of the supplied anchors.
2. Drive the supplied M3.5 screw into the
hole until the screw's head extends
about 1/8 inch from the wall.
3. Align the keyhole slot on the bottom of
the receiver with the screw in the wall,
then slide it down to secure it.
/1706+0)"6*'"
64#05/+66'4"
1. Remove the transmitter from the holder.
2. Use the holder as a template to mark
two screw holes on the wall.
3. Remove the holder from the mounting
surface and drill two
holes. Insert one of the supplied
anchors into each hole.
3
/16 inch diameter
4. Drive a screw through the holder into
each hole.
5. The transmitter can be slid in and out of
the holder. To lock the transmitter, fix it
with a size M2.6 screw at the bottom of
the holder.
+056#..+0)"
$#66'4+'5"#0&"
5'.'%6+0)"%*#00'.5
The door chime requires three AAA batteries
in the transmitter and three C batteries in the
receiver. For best performance and longest
life, we recommend RadioShack alkaline
batteries.
+0"6*'"64#05/+66'4
1. Slide the transmitter's battery
2. Use a small flat-blade screwdriver to
....
compartment door in the direction of the
arrow to remove it.
slide the switch inside the battery
compartment to the desired channel for
the transmitter.
2002 RadioShack Corporation.
©
RadioShack and RadioShack.com are trademarks
All Rights Reserved.
used by RadioShack Corporation.
"016'"±"
±
The channel settings must be the same for the
transmitter and the receiver. If the door chime
occasionally sounds without anyone pressing
BELL, change the channel settings for both
the transmitter and receiver.
"016'"±"
±
•Press BELL until the transmitter’s indicator
lights. Otherwise, the receiver may not work
properly.
• If you don't want to hear the door chime,
slide ON/OFF on the receiver to OFF.
3. Install three AAA batteries as indicated
by the polarity symbols (+ and –)
marked inside.
4. Replace the compartment door. If the
transmitter's LED indicator dims,
replace the batteries.
+0"6*'"4'%'+8'4
1. Slide the receiver's battery
compartment door in the direction of the
arrow to remove it.
2. Slide the switch inside the battery
compartment to select the same
channel for the receiver as is selected
for the transmitter.
±
3. Install three C batteries as indicated by
the polarity symbols (+ and –) marked
inside.
4. Replace the compartment door. If the
receiver's LED flashes with a short
beep tone, replace its batteries.
12'4#6+10
Slide
and hold down
Transmit begins, the indicator lights, and the
receiver sounds the door chime twice.
75+0)"6*'"%*+/'"#5"#0"
064;"%*+/'
'
1. Connect the transmitter to a normally
open alarm sensor. You need 2conductor wire (not supplied) to make
this connection.
2. Split the ends of the wire, then connect
the wire from the sensor's switch to the
screw holes on the back of the
transmitter, using the two supplied
machine screws. If the sensor you are
using has both normally open and
normally closed contacts, be sure to
connect to the sensor's normally open
contacts.
3. Slide
on the receiver to ON. Press
ON/OFF
on the transmitter.
BELL
ON/OFF
on the receiver to ON.
±
6*'"(%%"9#065";17"
61"-019
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
FCC Rules
. These limits are designed to
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult your local RadioShack store or an
experienced radio/TV technician for help.
• If you cannot eliminate the interference, the FCC
requires that you stop using your door chime.
Changes or modifications not expressly approved by
RadioShack may cause interference and void the user’s
authority to operate the equipment.
This device complies with Part 15 of the
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
FCC Rules
.
52'%+(+%#6+105
Frequency ........................433.92 MHz ± 600KHz
Transmitter current consumption...............<10mA
Receiver current consumption...<2mA @ standby
Receiver battery low.......................... 2.4V
Receiver audio power...............> 80dBA @ 25cm
Transmitter operating
temperature ..................................–20
Specifications are typical; individual units might
vary. Specifications are subject to change without
notice.
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for
one (1) year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees
and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack
MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN
LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS
PROVIDED HEREIN, RadioShack SHALL HAVE NO LIA BILITY
OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS
OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT
OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT
NOT LIMITED TO, ANY DAMAGES R ESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may
not apply to you.
In the event of a product defect during the warranty period, take
the product and the Radi oShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provide d by law : (a) co rre ct the d efe ct b y
product repair without charge for parts and labor; (b) replace
the product with one of the same or si milar design; or (c) refund
the purchase price. All replaced parts and products, and products on which a refund is made, become the property of
RadioShack. New or recond itioned parts and products may be
used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of
the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: ( a) damage or fa ilure caused by
or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other
incidence of excess voltage or current; (b) any repairs other
than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic
damage; (e) transportation, shipping or insurance costs; or (f)
costs of product removal, installation, set-up service adjustment
or reinstallation.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,
< 130mA @ sound playing
(–4
Fort Worth, TX 76102
± 0.1V
C to 60°C
°
F to 140°F)
°
12/99
RadioShack Corporation
Fort Worth, Texas 76102
63-1123
AO0113AAA1
07A02
Printed in China
Loading...