Connecting Your Phone
1.Plug one end of the supplied modular cord into the LINE jack
on the back of the phone.
2.Plug the other end into a modular phone line jack.
Notes:
• Your telephone connects directly to a modular phone line
jack. If your phone line jack is not a modular jack, you can
update the wiring yourself using adapters and jacks from
your local RadioShack store. Or, call your telephone
company to update the wiring for you.
• The USOC number of the jack to be installed is RJ11C.
Connecting the Handset
1.Plug one end of the supplied coiled cord into HANDSET on
the back of the base.
2.Plug the other end into the modular jack on the handset.
Setting the Dialing Mode
You may set your dialing mode to pulse or tone by selecting P or
T on the back of your base.
If you are not sure which service you have, do this simple test.
1.Set MODE to T.
2.Lift the handset or press SPEAKER and listen for the dial
tone.
3.Press any number other than 0.
• If your dial tone stops, you have touch-tone service.
Leave MODE on T.
• If the dial tone continues, you have pulse service. Set
MODE to P.
Note: TB is designated for use in the UK.
Using Tone Services on a Pulse Line
If you have a pulse line, you might need to use tone service for
special services, such as bank-by-phone. To use tone service,
do the following:
1.Be sure MODE is set to P and dial the number.
2.When the system answers, press
∗. Any addtional numbers
you press will send a tone signal.
After you hang up, your phone automatically resets to pulse dialing.
20-Number Memory Speaker Phone
43-3911
Your phone’s display is protected by a plastic label
during shipping. Peel off the label before using your
phone.
Installing Batteries
Insert 3 AAA batteries (not supplied). When appears or
the display becomes dim, replace the batteries.
• When replacing batteries, be sure to put in new batteries
within one minute of removing the old ones. If not, your time
and date will be lost.
• Use only fresh batteries of the required size and recommended type.
• Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities.
• Always remove old or weak batteries. Batteries can leak chemicals that may destroy electronic
parts.
Setting Up Your Phone
Preparing Your Phone
Battery
Compartment
MEM - Lets you store a number in
an indirect memory location (0-9).
See page 2.
M1 - M10 - lets you store 10
numbers and dial them with the
touch of a button.
REDIAL - lets you redial the last number
you dialed.
Mute - lets you talk to someone else
in the room without being overheard
by the person(s) on the phone.
Flash - lets you answer another
call if you have Call Waiting.
STORE - press to store numbers
in memory locations. See Memory
Dialing on page 2.
Opt/P - lets you select different
dialing options based on the
number you are calling.
Callback - lets you dial a phone
number in the Caller ID record
with the touch of a button.
Hold - lets you put a call on hold
while you do something else.
SPEAKER - press to switch between
the handset and speaker phone for
convenient hands-free use.
VOLUME - lets you control the
volume of the sound through your
handset and speaker phone.
Review - lets you scroll up
or down to set the desired
language, LCD contrast,
area code, and time/date
Also lets you scroll through
all numbers in your Caller
ID memory.
DELETE - lets you confirm your settings
during setup. Also lets you delete
records from your Caller ID memory.
3-Line LCD - lets you
review up to three lines of
information in your Caller
ID memory.
LINE
Jack
HANDSET
Jack
Ringer Volume - Hi/Low/Off
Set ringer’s volume to Hi or
Low as desired. Set to Off
for no sound.
MODE
P/T
Ringer R1/R2 - Set to
R1 for a high number of
rings or R2 for a lower
number of rings.
Battery Compartment
Plug your phone cord into
a modular phone line jack.
After you install your batteries, system information appears in the display, followed by E for English, F
for French and S for Spanish.
1.Repeatedly press REVIEW
e or d to select the desired language and press DELETE to store it. If
you do not select a language within a few seconds, the system defaults to English, the default
display language.
2.When LCD CONTRAST appears in the display, repeat step 1 to select one of the six settings.
3.When 000 SET AREA CODE displays and the 0 flashes, repeatedly press REVIEW
e or d until the
first digit of your area code appears. Press DELETE to store it. Repeat for each digit of your area
code.
Note: If you do not press a button, the system automatically sets the area code to 000.
4.Press REVIEW
e or d to set the hour, and press DELETE to store it.
Note: If you do not press a key, the system automatically sets the time to 12:00 PM 1/01.
5.Repeat Step 4 to store the minute, month and date.
To reset the language, contrast, area code and time/date settings:
1.Hold down DELETE and press d. LCD CONTRAST displays.
2.Repeat Step 1 above to reset each setting.
Choosing Your Settings
Index Card - Use the
supplied index card to
record the stored numbers.
Limited One-Year Warranty
©2004. RadioShack Corporation. 43-3911
All Rights Reserved. Printed in China
RadioShack and RadioShack.com are trademarks 12A04
used by RadioShack Corporation.
This product is warranted by RadioShack against manufacturing defects in material and workmanship under
normal use for one (1) year from the date of purchase from RadioShack company-owned stores and authorized
RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY
WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME,
DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as
proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law:
(a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the
same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which
a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in
the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of
the original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident,
misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance,
alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by
a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e)
transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment
or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
Important Safety Instructions
You can store up to 20 of your most frequently dialed
phone numbers, and dial the number by using one of
your memory locations (M1-M10 or 0-9).
Storing Numbers in Memory Locations
1.Press STORE.
2.Enter the phone number you want to store, including
1+ area code for long distance numbers.
3.Press any of the M1-M10 memory buttons.
To store the number to an indirect memory location,
press MEM and then press any key between 0 and
9.
4.Use the supplied index
cards to record your
stored numbers.
Notes:
• You can store up to 16
digits for each number.
• If you make a mistake
while entering the
number, press STORE
twice, and then re-enter
the phone number.
• To change a number in
memory, store a new
one in its place.
Entering a Pause in a Memory Number
In some telephone systems, you must dial an access
code (9, for example), wait for the second dial tone,
and then dial the number.
Press OPT/P to enter a three-second pause. For a
longer pause, press OPT/P again. Each time you do
this, one digit of memory is being saved.
Note: For more information about OPT/P, refer to the
section “Using OPT/P.”
Dialing a Memory Number
Press the desired location number (M1-M10).
To dial a number stored in the indirect memory
location, press MEM and the location number (0-9).
Chain Dialing
You can make a call using more than one of the
phone’s memory locations. Chain dialing is useful for
dialing special services, such as alternate long
distance or bank-by-phone.
Testing Stored Emergency Numbers
If you want to test a stored emergency number (police
department, fire department, ambulance), make the
test call during the late evening or early morning hours
to avoid peak demand periods. Remain on the line to
explain the reason for your call.
If you subscribe to Caller ID service, the phone company sends information
about the call between the first and second rings of every call you receive. The
phone can also show the name of the caller if you have that service.
Note: If the Caller ID record is garbled, LINE ERROR appears in the display.
Reviewing Caller ID Records
Each time you receive a call, your phone stores a Caller ID record that you can
review later. The record includes the following:
• Call number (1, 2, 3, etc.)
• Time and date of the call
Repeatedly press REVIEW
e / d to see Caller ID records. -END OF LIST-
appears after the first or last Caller ID record as you scroll through the list.
Notes:
• Your display can show up to 11 digits of a phone number. If the number is
longer, the display shows only the last 11 digits.
• The phone returns to the time/date display after about 20 seconds, if you
do not press a key.
Deleting Caller ID Records
You can delete individual Caller ID records, or delete all of them after you
review them. You cannot delete Caller ID records that ha ve not be en revie wed
or during a call.
• To remove a single Caller ID record, press DELETE twice.
• To remove multiple records, hold down DELETE until DELETE ALL?
appears. Then, press DELETE once. NO CALLS appears in the display
• If you have unread records while holding down DELETE, xx NEW CALLS
and PLEASE READ display alternately. Review the records first before
deletion.
Using OPT/P
Your phone provides dialing options for different phone systems, allow
you to select the correct dialing selection for a phone number before
you press CALLBACK.
1.Repeatedly press REVIEW e / d to find the phone number you want.
2.Repeatedly press OPT/P to select the desired dialing option. You can select
one of the following:
• seven-digit number
• 10-digit number (area code + number)
• 11-digit number (1 + area code + number)
Using Callback
Press CALLBACK to automatically dial the number displayed in the Caller ID
display.
If the Caller... Display Reads
Left a message MSG
Called more than once REPEAT
Blocks their number or name PRIVATE
Is not within a Caller ID area OUT OF AREA
Is calling long distance LONG DISTANCE
• When using your telephone equipment, basic safety
precautions should always be followded to reduce the
risk of fire, electric shock, and injury to persons,
including the following.
• Do not use this product near water, for example, near
a bathtub, washbowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.
• Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk
of electric shock from lightning.
• Do not use the telephone to report a gas leak in the
vicinity of the leak.
• Use only the batteries indicated in this manual. Do not
dispose of batteries in a fire. They may explode.
Check with local codes for possible special disposal
instructions.
Memory Dialing
Caller ID Operation
FCC
Your phone complies with Part 68 of FCC Rules. You must, upon request,
provide the FCC registration number and the REN to your telephone
company. Both numbers are on the bottom of the phone.
Note: You must not connect your phone to:
• coin-operated systems
• most electronic key telephone systems
• party-line systems
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission, or corporation
commission for information.
We have designed your phone to conform to federal regulations, and you can
connect it to most telephone lines. However, each phone (and each device,
such as a telephone or answering machine) that you connect to the
telephone line draws power from the telephone line. We refer to this power
draw as the device's ringer equivalence number, or REN on the bottom of
your phone.
If you use more than one phone or other device on the line, add up all of the
RENs. If the total is more than five (three in rural areas), your telephones
might not ring. If ringer operation is impaired, remove a device from the line.
In the unlikely event that your phone causes problems on the phone line, the
phone company can temporarily discontinue your service. If this happens,
the phone company attempts to notify you in advance. If advance notice is
not practical, the phone company notifies you as soon as possible and
advises you of your right to file a complaint with the FCC.
Also, the phone company can make changes to its lines, equipment,
operations, or procedures that could affect the operation of this telephone.
The telephone company notifies you of these changes in advance, so you
can take the necessary steps to prevent interruption of your telephone
service.
SURGE PROTECTION
Your telephone has built-in protection circuits to reduce the risk of damage
from surges in telephone line and power line current. These protection
circuits meet or exceed the FCC requirements. However, lightning striking
the telephone or power lines can damage your telephone.
Lightning damage is not common. Nevertheless, if you live in an area that
has severe electrical storms, we suggest that you unplug your phone when
storms approach to reduce the possibility of damage.
• Keep your phone dry; if it gets wet, wipe it dry
immediately.
• Use and store your phone only in room temperature
environments. Handle your phone carefully; do not drop
it.
• Keep your phone away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it looking new.
Care
Troubleshooting
No dial tone - Be sure the handset and phone line cords
are securely connected.
Display is blank - Be sure batteries are correctly installed.
Volume drops or sound is distorted - Be sure any other
phones are not being used.
Call is noisy - Check to see if the cords are securely
connected.
Can receive calls, but cannot make calls - Set MODE to
the correct dialing mode, P or T.
No Caller ID information appears - You have not
subscribed to Caller ID service with your phone company.
• Modifying or tampering with your phone's internal
components can cause a malfunction and might
invalidate its warranty and void your FCC authorization
to operate it.
Repair
MEM
M1-M10
• Caller’s phone number
• Caller’s name (if you have this service)
Loading...