RadioPopper Nano User Manual

User Guide

Nano

Light blinks to indicate channel

NANO

1 2 3 4

CHAN

SET

POWER

TEST

Double Tap:

Change Channel

Touch & Hold:
Power On/O
Single Tap:
Test Trigger

Guide Contents

Battery Level Indicator . . . . . . . . . . . . . . .

Touch Sensitive Buttons . . . . . . . . . . . . .

Power Saving Modes . . . . . . . . . . . . . . . .

Transmitter Auto Power O . . . . . . . . . .

Receiver Auto Power O . . . . . . . . . . . . .

RadioPopper Support . . . . . . . . . . . . . . .

Nano Specications . . . . . . . . . . . . . . . . .

FCC & IC Statements . . . . . . . . . . . . . . . . .

After each trigger or test trigger, the Nano will
indicate its battery level by blinking
1, 2, 3, or 4 lights.

1 2 3 4

Approximate
Battery Level

4

1 2 3 4

1 2 3 4

1 2 3 4

4
5
6
7
8
9
10
11

100%

75%

50%

25%

Touch Sensitive Buttons

Your new RadioPopper Nano features touch
sensitive buttons. There is no need to “press”
on the unit. Simply touch your nger to the
button area.

Touch and hold POWER/TEST to turn the
unit on or o.

5

Power Saving Mode

In the unlikely event your Nano is left on or
is accidentally powered on when not in use,
several power saving features have been
included in both the transmitter and receiver
units. These features will automatically power
down the Nano to prevent unintentional
drain of battery.

6

Transmitter Auto Power O

If your Nano transmitter is not triggered
or test red for more than one hour, it will
automatically power down. If you trigger
the Nano transmitter after this power down
(by taking a picture with your camera for
example), the Nano will automatically power
up and resume normal operation.

7

Receiver Auto Power O

Your Nano receiver senses when it is
attached to a ash or studio strobe. If there
is nothing attached (or turned on) for more
than ve minutes, the Nano receiver will
automatically power down. Once it again
senses an attached ash or studio light, the
Nano receiver will automatically power up
and resume normal operation.

8

Support

We love and support our customers.
Contact us anytime if you have any
questions.

www.radiopopper.com
[e-mail]
360-713-0776

9

Specications

Battery (Tx and Rx):
One “CR123” Size Battery, 3.0v. Rechargeable approved.

Battery Life:
Transmitter: 150 - 300 hours continual running time.
Receiver: 75 - 100 hours continual running time.
(Depending on battery type and quality)

Radio Frequency:

902-928 MHz, ISM Band

Radio Range:

Up to 1750 ft depending on conditions and environment.

Maximum Sync Speed:

1/500 for cameras having leaf shutters.

10

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.

This equipment has been veried to comply with the limits for a class B
computing device, pursuant to FCC Rules. Operation with non-approved
equipment is likely to result in interference to radio and TV reception. The user
is cautioned that changes and modications made to the equipment without
the approval of manufacturer could void the user’s authority to operate this
equipment.

FCC ID: V4TNT2

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired operation.

Important Note: To comply with FCC RF exposure compliance requirements,
the following antenna installation and device operating congurations
must be satised - This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or transmitter.

INDUSTRY CANADA INFORMATION

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.