RadioLink CB86-PLUS User Manual

Lithium battery balance charger CB86-PLUS

User Manual

Radiolink Electronic Co., Ltd

Web Site:http://www.radiolink.com.cn

Warning : High powered product ,please use it within sight !

FCC

INTRODUCTION

Thank you for purchasing Radiolink high precision independent balance charger
CB86-PLUS .
CB86-PLUS, open the era of high precision independent balance charge, integrate 6
ways for charge current and equipped exclusive charging circuit for every single battery
cell, which realize batteries don’t affect each other in independent balance charge system.
Support max 6A charge current for 8 battery packs charging with capacity analyzed and
inner resistance assessed, compatible with 1S-6S battery packs. 0.001V balance
precision, better than the average 0.01V. Unique USB flash drive upgrade. Charging
diaries, including initial voltage, complete voltage and charge-discharge voltage, etc.

Analyses of every battery cell’s capacity in each group and assess of internal resistance.

Precision voltage and trickle repairing restore the high-power of over-discharged battery.
Suggestion :when you read this manual,please connect the charger and other related
equipment ,operating while reading. Any questions when using CB86-PLUS, please refer
to the manual or call our after_service [phone] or login BBS (such as

www.rcgroups.com, www.5imx.com, www.rcfans.com ) to check the issues related

answer to questions.

Due to unforeseen changes in production procedures , the information contained in this
manual in subject to change without notice.
more information please check our website as below:

http://www.radiolink.com.cn

CUSTOMER SERVICE

Contact Us

Tel: [phone]
Fax: [phone]
Email: [e-mail]

Programming and User questions

Tel: [phone]
Fax: [phone]
Email: [e-mail]

一、Function：

CB86S Technical data:
Input Voltage：Voltage range 10.5-15V(The charge will not work with wrong input power
polarity, warning when input power voltage over 15V and less than 10.5V, temperature
over 48C° will auto-start fans)

Voice Indicator：ON/OFF
Time setting: Charging or discharging time from 0 to 99 minutes and 59 second
Charging Mode: Cycle charging, parallel charging, discharging, voltage measure
Charging voltage: 0.00V-4.23V，setting precision 0.01V；
Discharging voltage: 2.00-4.23V，setting precision 0.01V；
Charging current：0.0-6.0A，setting precision 0.1A；
Discharging current: 1.05A

二、Operation：

1、Connection

Connect the charger with a DC power source of output voltage 10.0-5V and current not

less than15A.
Balance plug:
CB86S contains 8 balance ports, it can charge 8pcs 6-cell Lithium battery at the same
time connecting 1S-6S batteries freely by the following sketch. Mind the polarity of

Input
Voltage

Charging
Mode

Voice
Indicator

Charging
Time

Final Voltage

Charging Current

START/STOP:

To start or stop
present status

“+/▲”，“-/▼”: Add or reduce

present data (on charging or
discharging mode)

SET：Set data of the charger

(Forbidden on charging
and discharging status)

batteries (black cable is negative and it shall connect with right side, the red positive
connecting to left side.)
Diagrammatic sketch:

The above sketch is shown by a 4-cell and a 2-cell batteries connected in two ports. Also
you can connect a 6-cell battery in one port, or 3 pcs 2-cell in different port, or 2pcs 3-cell
batteries to different port. Shown by sketch below:

（1）connect with 3pcs 2-cell batteries：

（2）connect with one 6-cell battery：

Red cable（positive）
always on the left

Black cable（negative）
always on the right

（3）connect with two 3-cell batteries：

2、Button instruction：

START/STOP：

To start or stop the current status, it is available at any time, so it’s important to finish
all parameter (voltage and current) setting for charging or discharging before press this
button.

SET：

Only the charger is not working, this button is enabled. Press SET to enter menu of

setting for VOICE, FUNCTION, CURRENT, VOLTAGE and BETTERY GROUP. When
one of the options displayed reversed, use the button key “+/▲” or “-/▼” to get the
relative data.

Voice indicator：

When the charging stopped, press SET to choose the option VOICE INDICATOR,

and use“+/▲” or “-/▼” to set voice ON or OFF. Then press SET to choose the next
option.

Charging port：

When the charging stopped, press SET to choose the option PORT, press “+/▲”or

“-/▼” to choose the port and then press SET for next option.

Function：

When the charging stopped, press SET to choose FUNCTION, press “+/▲” or“-/▼” to
select different status: CYCLE CHARGING, PARALLEL, DISCHARGING, VOLTAGE
MEASURE, and then press SET for next option.

Voltage and current setting：

When the charging stopped, press SET to choose the option VOLTAGE/ CURRENT,

and then press“+/▲”or“-/▼” to set voltage and current, then press SET for next

option.

3、Operation

Connect the charger with a DC power source of output voltage 10.5-15V and current
not less than 15A, and then connect a 6-cell battery with it, power on the charger.

（1）Interface powered on

1

（2）Press the key SET，set the mode CHARGING or DISCHARGING. Press the key

“+/▲”or“-/▼” to set voltage of discharging. Below sketch shows discharging setting
interface:（discharging current is not settable, and charging voltage and current can set by
yourself）

Present voltage
of the battery
cell

Charging

Charging current

Mode: discharging

External voltage

Discharging time