Radiodetection RD7200 User manual
™
RD7200
Utility cable and pipe locator range
User guide
90/UG119-AMERICAS/01
2
Preface
About this guide
CAUTION: This guide provides basic operating instructions for the RD7200
locator and transmitter. It also contains important safety information and
guidelines and as such should be read in its entirety before attempting to
operate the RD7200 locator and transmitter.
This guide is intended as a quick reference guide only. For detailed instructions,
including the use of accessories, help with eCert
Operation Manual and RD Manager
from www.radiodetection.com.
The online User Manual library also contains links to the RD Manager Online manuals.
Certificates of conformity for the RD7200 locators and Tx transmitter ranges can be
found at www.radiodetection.com.
™
Online manuals, which are available for download
™
, please refer to the RD7200 locator
3
WARNING! Direct connection to live conductors is POTENTIALLY LETHAL.
Direct connections to live conductors should be attempted by fully qualified
personnel only using the relevant products that allow connections to energized
lines.
WARNING! The transmitter is capable of outputting potentially lethal voltages.
Take care when applying signals to any pipe or cable and be sure to notify other
technicians who may be working on the line.
WARNING! Reduce audio level before using headphones to avoid damaging
your hearing.
WARNING! This equipment is NOT approved for use in areas where
hazardous gases may be present.
WARNING! When using the transmitter, switch off the unit and disconnect
cables before removing the battery pack.
WARNING! The RD7200 locator will detect most buried conductors but there
are some objects that do not radiate any detectable signal. The RD7200, or any
other electromagnetic locator, cannot detect these objects so proceed with
caution. There are also some live cables which the RD7200 will not be able to
detect in Power mode. The RD7200 does not indicate whether a signal is from a
single cable or from several in close proximity.
WARNING! Batteries can get hot after prolonged use at full output power.
Take care while replacing or handling batteries.
WARNING! Only use charging equipment provided by Radiodetection. The use of
alternative chargers may cause a safety hazard and/or reduce the life of the battery.
CAUTION: Do not let your battery completely discharge as this may reduce its life
or damage it permanently. If you are not using your equipment for a long period
do charge them at least once a month.
WARNING! Batteries can get hot after prolonged use at full output power.
Take care while replacing or handling batteries.
WARNING! Do not tamper with, or attempt to disassemble the battery packs.
CAUTION: If battery failure is suspected or if the battery shows any sign of
discoloration / physical damage return the entire unit to an authorized repair
center for investigation and repair. Local, national or IATA transport regulations
may restrict the shipment of faulty batteries. Check with your courier for
restrictions and best practice guidelines. Your local Radiodetection representative
will be able to direct you to our authorized repair centers.
NOTE: The charging temperature range is 0 to 45 °C, 32 to 113°F. Do not attempt
to recharge your batteries outside this temperature range.
4
3 Year Extended Warranty
RD7200 locators and transmitters are covered by a 1 year warranty as standard.
Customers can extend their warranty period to a total of 3 years by registering
their products within 3 months of purchase.
To register your product:
Visit https://portal.radiodetection.com to create your portal account* and use
the Product page to register your locator or transmitter.
Visit https://support.radiodetection.com for instructions on how to create a
portal account or register your product.
* A valid email address and mobile number are required.
eCert and Self-Test
The RD7200 locator is safety equipment which should be regularly checked to
ensure its correct operation.
eCert provides a thorough test of the RD7200’s locating circuitry, and supplies a
Radiodetection Calibration Certificate when a positive test result is obtained.
To run an eCert, the locator should be connected to an internet-enabled PC on
which the RD Manager software is installed.
Refer to the RD Manager operation manual for further details. Additional purchase
may be required.
RD7200 locators incorporate an Enhanced Self-Test feature. In addition to the
typical checks for display and power functions, the RD7200 locator applies test
signals to its locating circuitry during a Self-Test to check accuracy and performance.
We recommend that a self-test is run at least weekly, or before each use.
5
RD7200 locator
1 2 4
8
5
3
6
19
20
21
22
23
16
7
9
17 1818
31
29
32
12
13
10
11
14
14
15
24 25 2730 2826
6
Locator features
1. Keypad.
2. LCD with auto backlight.
3. Haptic (vibration) feedback.
4. Speaker.
5. Battery compartment.
6. Accessory connector.
7. Headphone connector.
8. Bluetooth
9. Swing alert system.
10. Optional Lithium-Ion battery pack.
11. USB port
(inside battery compartment).
®
module.
Locator keypad
12. Power key.
13. Frequency key.
14. Up and down arrows.
15. Antenna key.
25. A-Frame icon.
26. Frequency / current / menu readout.
27. Antenna modes icon:
Indicates antenna mode selection:
Peak/Peak+
28. Sonde icon: Indicates that a sonde
signal source is selected.
29. Line icon: Indicates that a line signal
source is selected.
30. Compass: Shows the orientation
of the located cable or sonde relative
to the locator.
31. Transmitter standby indicator.
32. Depth readout.
™
/Null/Guidance.
Locator screen icons
16. Signal strength bargraph with peak
marker.
17. Signal strength readout.
18. Null / Proportional Guidance arrows.
19. Battery level.
20. Sensitivity readout
21. Volume level.
22. Radio Mode icon.
23. Power Mode icon.
24. Accessory / Measurement icon.
7
Loading...