Radiodetection RD2000 Super C.A.T+, RD2000 Super C.A.T CPS, RD2000 Super C.A.T TL, RD2000 T1 Transmitter, RD2000 Super C.A.T S User Manual

RD2000 SuperC.A.T

™

RD2000: SuperC.A.T

+

SuperC.A.T

TL

SuperC.A.T

S

SuperC.A.T

CPS

T1 Transmitter

User Guide

RD2000 SuperC.A.T User Guide

Functions

SuperC.A.T Locator functions

On/Off Trigger. Press and hold to use
the SuperC.A.T. Release to switch off
the SuperC.A.T.

Sensitivity Control. Rotate to increase or
decrease detection sensitivity.

Loudspeaker. Unscrew to detach.

LCD Meter with automatic depth readout.

Battery compartment. To replace batteries,
open the access cover using a screwdriver
or coin. Use two LR20 or D type alkaline
batteries (or equivalent NiMH rechargeable
batteries).

Function Switch.

1

2

3

4

5

6

3

4

1

2

6

5

1

3

2

4

5

SuperC.A.T LCD functions

Battery Indicator.

Mode: is selected using the function switch (if it is indicated):

L = Active line mode,

R = Radio, P = Power,

C = CPS (optional),

S = Sonde (optional),

Depth,

Signal strength as indicated by the bar graph,

Frequency selection button.

1

2

a

b

c

d

3

4

5

Depth Measurement

The SuperC.A.T will automatically measure and display the depth in
Active Line, Sonde and CPS modes. Note: The SuperC.A.T does not
measure depth in Power or Radio modes.

Method: Locate the utility as follows. Hold the SuperC.A.T still and
vertically centered above the detected line and across the line of the
pipe/cable.

Note: A depth measurement will not be displayed where environmental

conditions are poor (e.g. weak signal or interference).

The measurement is to the center of the pipe/conductor or to the center
of the Sonde, which may rest at the bottom of the pipe.

The measurement accuracy is ± 5% or better under standard earth

conditions and with undistorted elds. When digging for cables after

location, it is imperative that due care is taken appropriate to the danger
of personal injury and damage to infrastructure. It is recommended that
depth measurement is repeated throughout an excavation.

The SuperC.A.T is switched on by pressing and holding the
On/Off trigger. You will hear an initial “chirp” sound. Low battery

is indicated by a ashing battery icon and a lower pitch chirp.

Power and Radio mode location

Note: After completing a power mode sweep we recommend that you

repeat the procedure in radio mode; the procedure is the same.

Power Mode

Power mode detects power signals radiated by loaded power cables.
To select Power mode, rotate the function switch until the LCD displays
a P icon. Rotate the sensitivity control fully clockwise for maximum

sensitivity but reduce if there is a blanket signal across the site. Dene

the excavation site and carry out a grid pattern sweep. Note that
sometimes the signal may be re-radiated from other conductors.

Sweep the site holding the SuperC.A.T
upright at your side. Continue the sweep
beyond the perimeter of the site. The
presence of a buried conducting pipe or
cable will be indicated by a tone emitted
from the loudspeaker and a kick on the

LCD’s bar graph.

Keep the SuperC.A.T blade vertical and
move slowly backwards and forwards over
the conductor. Reduce the sensitivity for a

narrower response; this will allow you to pinpoint the conductor. With the
SuperC.A.T use the meter deection to aid pinpointing. Maximum meter
deection and audible volume from the speaker will indicate the position

of the conductor.

When directly over the conductor and with the sensitivity level set for

a narrow response, rotate the SuperC.A.T on its axis until the signal
minimum is found. The blade is now parallel with the conductor.

Trace the conductor beyond the site and mark the position as required
with chalk or paint.

Radio Mode

Radio mode detects broadcast signals that originate from radio
transmitters. These signals penetrate the ground and are re-radiated by
buried conductors. However, depending on your location, these signals
may not be present.

StrikeAlert™

If the StrikeAlert™ option is activated, the mode icon will ash an
asterisk (*) when the locator detects a shallow cable radiating an
electromagnetic signal. This is a useful shallow cable indicator;
note however that not all live power cables radiate a signal that
the Receiver can detect. StrikeAlert is indicated by a I or O at
power-up.

Do not use the StrikeAlert™ feature to conrm the area is free from
shallow cables. ALWAYS DIG WITH CAUTION.

Note: To disable StrikeAlert™, press and hold the frequency select

button as you turn the Receiver on. Repeat the procedure to enable
StrikeAlert™.

StrikeAlert does not operate in radio or sonde mode. It is activated by
shallow cables radiating a power signal or an actively applied signal.

T1 – 1W Transmitter

The T1 is a general purpose, 1 Watt, transmitter that provides up to

three locatable frequencies, two induction frequencies and two power
levels. By default, the T1 induces a signal directly into the ground. It
is the perfect companion to the SuperC.A.T range of cable and pipe
locators.

Transmitter features

On/Off/Frequency Selector – LEDs

indicate which frequency has been
selected.

First press switches the
Transmitter on and selects
the low locate frequency

– depending on product
specied (not an induction

mode).

1

a

Second and third press selects the next specied frequencies:

Active and Induction.

Fourth press turns the Transmitter off.

Power Selector

Selects either high or low power level. LEDs indicate which power

level is active.

Connection Socket

Connects cables or optional accessories such as the Signal

Clamp, Live Cable Connector or Live Plug Connector. When

connected, induction mode is disabled. A loudspeaker emits

a pulsing tone to indicate sufcient battery charge and a

satisfactory direct connection.

b

c

2

a

3

a

3

1

2

4

5

Batteries Access Panel. No tone indicates that the batteries must
be replaced. Unscrew fastener on the rear panel and replace with 4
LR20 (D cells) batteries. Observe correct battery polarity as indicated
on the top-panel label.

Arrows

The arrows on the top panel label indicate the required
Transmitter alignment above the pipe or cable when using the
Induction mode. The arrows and the pipe or cable must be
parallel. Alignment is not required when the T1 is in Active mode.

Note: Turn off the T1 and remove any connection cables before

changing batteries.

Connection Cable

The red cable connects the T1 directly to the target cable or pipe. The
black cable provides the ground return when clamped to a Ground
Stake. The connection cable plugs and locks into the connection socket
on the front panel of the T1. To unlock the cable, grip the black sleeve
on the outside of the plug and ease off the connector. Do not pull the
wire as this may damage the cable and/or socket.

Ground Stake

The Ground Stake, when connected to
the black ground cable, provides a ground
connection and return signal to the T1.

Regularly check your SuperC.A.T and
T1, in all modes over a cable which
provides a response that you are
familiar with.

4

5

a

Cable location with the SuperC.A.T and T1
Transmitter

Induction Mode

The Transmitter has an internal aerial that will induce a signal onto a line
(or lines) directly below it. This is useful when you do not have direct
access to the line. Generally, induction is only effective to depths of 2m

(6’6”). Note that the induction mode is indiscriminate and will apply a

signal to all conductors within its range.

Induction is only available with frequencies 8kHz and above.

Procedure

Place the Transmitter over the approximate position of the line with
arrows pointing parallel to the line. Set SuperC.A.T Receiver sensitivity
to 50% and start locating the line at least 10 meters away from the
Transmitter. Mark the ground when the Receiver detects any
signal spike.

Note: Induction cannot apply a signal to a line below reinforced concrete.

The SuperC.A.T may detect the transmitter signal directly from the T1
rather than the target line, so do not attempt depth measurements
within 10 meters of the transmitter.

To check if you are detecting a signal from the T1, point the Receiver
directly at the transmitter. If the Receiver signal strength increases,
either reduce the transmitter power or increase the distance between
you and the transmitter.

If the Receiver signal strength decreases, the signal is from the
buried line.

Direct Connection

Direct connection allows you to apply a signal directly onto a specic

line. Direct connection is suitable for use on continuous tracer wire,
water and gas distribution systems, a telecom cable, and pipeline at a
CP test or other access point.

Procedure

First Plug the Connection Cable into the Transmitter and then clamp the
terminals onto the target cable or pipeline. If necessary clean off paint,
rust or scale to ensure good connection.

Clip the ground cable to an independent grounding point a few
meters away from the transmitter and preferably perpendicular to
the probable route of the target cable or pipeline. Do not attach the
ground cable to water pipes or any buried line which could carry
the induced locate signal.

Start with the T1’s lowest power setting. A pulsed loudspeaker tone

indicates a good connection. If there is no tonal change, check the
electrical contacts and the ground. If necessary, change the position of
the ground stake or pour water over the ground contact if placed in dry
soil or sand. If there is still no change in tone increase the power setting.

Note: A receiver can detect a signal many times weaker than what is

necessary for a transmitter tone change and short distances can be
traced without pulse tone from the loudspeaker.

WARNING! Direct connection to power cable sheaths must be

performed by qualied personnel!

Signal Clamp (optional extra)

The Signal Clamp applies a signal to a pipe or a live cable without
interrupting the supply. It applies a very discriminating signal with
reduced coupling to other conductors.

WARNING! To avoid the risk of electric shock, the signal clamp
must be connected to the transmitter before being placed around
the pipe or cable.

Procedure

Connect the Signal Clamp to the Transmitter.

Place the Signal Clamp around the pipe or cable, ensuring the jaws are
closed. Switch on the Transmitter.

Note that unless a disconnected pipe or cable is grounded, it cannot
generally be located using a Signal Clamp.

Locating a Sonde

The SuperC.A.T is capable of locating a Radiodetection Sonde. Before

attempting to locate a Sonde ensure that the Sonde’s batteries are fully

charged. Radiodetection recommends using new or fully recharged
batteries at the beginning of each day and preferably at the start of each
job. Also check that the Sonde and Receiver are operating at the same
frequency and are working correctly.

To test the Sonde and Receiver, position the Sonde at a distance equal
to its rated depth range from the Receiver. Point the Receiver at the
Sonde with its blade parallel to the direction the Sonde is travelling.
Check that the bar graph shows more than 50% at high sensitivity

Note: the blade of the new Receiver must be in line with the Sonde; this
is the opposite to Line locate method.

Procedure

Attach the Sonde to the rod and insert it into the Drain or Duct to be
mapped. Keep the Sonde just in view.

Hold the Receiver vertically directly over the Sonde with the blade in

line with the Sonde’s orientation.

Adjust the sensitivity of the Receiver to give a bar graph reading
between 60-80%.

A Sonde radiates a peak eld from the center of its axis with ghost

signals at each side of the peak. Move the Receiver to one side and
then along the axis of the Sonde forwards and backwards to detect the
ghost signals.

Radiodetection recommends locating the ghost signals as nding them
conrms the position of the main peak. To lose the ghost signals, reduce

the sensitivity of the Receiver; this should
leave only the main peak signal detectable.

With the Receiver sensitivity set as desired,

propel the Sonde along three or four meters
and stop. Place the Receiver over the
estimated position of the Sonde and:

Move the Receiver backwards and

forwards with the blade’s orientation

parallel to the Sonde.

1

2

3

1

Stop when the bar graph indicates a
clear peak.

Rotate the Receiver until the blade’s

orientation is perpendicular to the
Sonde, stop when the bar graph
indicates a clear peak.

Move the Receiver from side to side
until the bar graph indicates a clear
peak.

When the Receiver locates a peak

signal, it will automatically calculate
the depth of the Sonde. Observe
the depth reading while moving the
Receiver from side to side; the lowest
reading will be the correct location.

2

3

4

5

Repeat each step in smaller increments with the Receiver blade resting
on or near the ground. The Receiver should now be directly above the
Sonde with the blade in line with the Sonde; mark this position.

Propel the Sonde a further three to four meters along the pipe and
pinpoint and mark. Repeat the procedure along the route at similar

intervals. Note, while tracking the Sonde altering the receiver’s sensitivity

is not required unless the depth pipe, or the distance between Receiver
and Sonde changes.

Measuring Sonde depth

Pinpoint the Sonde as previously described. Then rest the Receiver on

the ground with the blade’s orientation parallel to the orientation of the

Sonde. Adjust the sensitivity to give a meter reading of 60% to 80% on

the LCD’s bar graph.

Note that the depth reading is the distance from the bottom of the
Receiver blade to the center of the Sonde and not to the drain or duct
being located.

CAUTION: Ensure Depth readings are taken from peak readings.
Depth readings taken from ghost signal position will be incorrect.

Depth measurement is automatic. Depth reading will be displayed when
the Receiver is moved slowly across the Sonde. The shallowest depth
reading displayed on the LCD is also the correct position directly above
the Sonde.

If the signal is too weak or unstable the Receiver unit will not calculate
depth. In this case use a more powerful Sonde or use the Pinpoint
procedure described below.

Pinpoint Procedure.

Move the Receiver ahead of the Sonde.

Ensure the blade’s orientation is parallel with the
Sonde’s orientation

Increase the sensitivity slightly to nd the ghost signal. Note that

between the main peak and ghost there is a Null or minimum.

Mark this position for reference.

Now move behind the Sonde and repeat step 1.

Find the Null between the ghost and main peak. See points A and B
on the diagram.

The higher the sensitivity of the Receiver the sharper the

Null’s appear.

Measure the distance between points A and B and multiply by 0.7 to
give an approximate depth measurement.

Live Plug Connector (optional extra)

The Live Plug Connector applies the Transmitter signal to a live domestic
power socket and via the domestic wiring system on the service cable
and the supply cable in the street. The signal should be detectable on
the supply system to a few hundred meters each side of the point of
application.

Note: Do not connect the Transmitter to live cables without using a Plug

Connector or Live Cable.

Procedure

Connect the Live Plug Connector to the Transmitter and to the live
domestic power socket. Switch on the socket.

Note: Live Plug Connector contains a protection unit to protect the user

and the Transmitter from mains voltage up to 250V.

Sweep the site holding the SuperC.A.T upright at your side. Continue
the sweep beyond the perimeter of the site. The presence of a
buried conducting cable will be indicated by a tone emitted from the

loudspeaker and a spike on the LCD’s bar graph.

Keep the SuperC.A.T blade vertical and move slowly backwards and
forwards over the conductor. Reduce the sensitivity for a narrower

response; this will allow you to pinpoint the conductor. With the
SuperC.A.T use the meter deection to aid pinpointing. Maximum
meter deection and audible volume from the speaker will indicate

the position of the conductor.

When directly over the conductor and with the sensitivity level set for

a narrow response, rotate the SuperC.A.T on its axis until the signal
minimum is found. The blade is now parallel with the conductor.

Trace the conductor beyond the site and mark the position as required
with chalk or paint.

1

a

b

2

3

4

5

6

Troubleshooting

When reporting any problem to your Radiodetection Dealer or Supplier it

is important to quote the unit serial number and the purchase date.

WARNING! This equipment is NOT approved for use in areas where

hazardous gases may be present.

Reduce audio level before using the earpiece.

Batteries should be disposed of in accordance with your
company’s work practice, and/or any relevant laws or guidelines
in your country.

This instrument, or family of instruments, will not be permanently
damaged by reasonable electrostatic discharge and has been tested

in accordance with IEC 801-2. However, in extreme cases temporary

malfunction may occur. If this happens, switch off, wait and switch on
again. If the instrument still malfunctions, disconnect the batteries for a
few seconds.

Radiodetection hereby declares that this T1 Transmitter is compliant
with the essential requirements and other relevant provisions of Directive

1999/5/EC.

WARNING! The SuperC.A.T will detect almost all buried conductors

but there are some objects which do not radiate any signal which
the SuperC.A.T or any other electromagnetic instrument is unable
to detect. There are also some live cables which the SuperC.A.T
will not be able to detect in Power mode. The SuperC.A.T does not
indicate whether a signal is from a single cable or from several in
close proximity.

Service and Maintenance

The SuperC.A.T and the T1 are designed so that they do not require
regular calibration. However, as with all safety equipment, it is
recommended that they are serviced at least once a year either at
Radiodetection or an approved repair center.

Radiodetection products, including this user guide, are under
continuous development and are subject to change without notice.
Go to www.radiodetection.com or contact your local Radiodetection
representation for the latest information regarding the SuperC.A.T, T1
or any Radiodetection product.

Training

Radiodetection provides training services for most Radiodetection

products. Our qualied instructors will train equipment operators or other

personnel at your preferred location or at Radiodetection headquarters.
For more information go to www.radiodetection.com or contact your
local Radiodetection representative.