Radicom Research RB1000 User Manual
Radicom Resear ch, Inc.
RB1000 ,
&
BPM1000FCE
RB1000HM
Serial
Bluetooth Modules
User’s Manual
RB1000/BPM1000FCE RB1000HM
August 9, 2012
1
Table of Contents
Introduction 3
Approvals 4
Electronic Characteristics 4
Firmware Upgrade List 5
Model and Ordering Information 6
RB1000/ BPM1000FCE Mechanical Dimensions 7
RB1000/ BPM1000FCE Surface Module Pin Definitions 8
RB1000/ BPM1000FCE Module Pin Descriptions 9
RB1000HM Mechanical Dimensions 10
RB1000HM Pin Descriptions 11
The AT Commands 12
Layout Design Suggestions 14
FCC & IC Label and Model Identification 15
Important Regulatory Compliance and User Information 16
CE Declaration of Conformity 18
Limited Warranty 19
Contacting Radicom 21
Information furnished by Radicom Research is believed to be accurate and reliable. However
Radicom Research assumes no responsibility for its use, or any infringement of patents or other
rights of third parties that may result from its use. Radicom Research reserves the right to change
circuitry at any time without notice. This document is subject to change without notice.
2
Introduction
Thank you for choosing Radicom RB1000 family Module. We are committed to providing you
quality service and technical support. The RB1000 modules are designed to meet OEM’s needs of
embedding
short-range, low power, wireless data connectivity to their products. The RB1000 family
offers a quick and simple solution for wireless Bluetooth communications.
The Radicom RB1000 family module is designed to meet the emerging market for Bluetooth 4.0
applications. These embedded Bluetooth 4.0 modules integrate entire profiles, applications, and
Bluetooth protocol stack, so no external processor is needed. The module contains an internal S-
Flash so custom parameters and settings can be easily loaded into these modules.
The RB1000 can be factory configured for other Bluetooth cost-effective and power-efficient
wireless consumer products such as watches, medical sensors, mice, TV remote controls and fitness
trainers. The model RB1000-S can also be used to connect to other Bluetooth 4.0 devices such as a
Bluetooth Dongle or PCs that support the Radicom BLE Data Protocol. Contact Radicom for help
adding the BLE Data Protocol functionality to your 4.0 Bluetooth device or for help in determining
which Bluetooth Module is the best fit for your particular Bluetooth application.
The RB1000 family modules can be powered directly with standard 3V coin cell or pair of AAA
batteries. In lowest mode it consumes only 600nA and will wake up in few hundred microseconds.
The RB1000 family provides superior performance in the presence of interference from 802.11
(WiFi) wireless devices and other 2.4GHz radios.
The RB1000 modules support quick connections and data transfers allowing an application to
establish a Bluetooth connection within a few milliseconds for short communication bursts before
quickly disconnecting the Bluetooth connection to save power. It takes much less time to make a
connection than conventional Bluetooth wireless technology and consumes approximately only
1/20
th
of the power of Bluetooth Basic Rate.
The RB1000 is available in surface mount (SMD) or through-hole (Dip) hardware designs. The
RB1000 module is the surface mount model. The RB1000 can also mounted on a conversion board
to create the RB100HM model for serial through-hole design
3
Approvals ~ Pending
•
FCC Part 15: 47 CFR FCC Part 15
Subpart C 15.247, 47 CFR FCC Part 15 Subpart B 2009 (Class B)
•
IC RSS-102, IC ES-003 issue 4, IC RSS-210 issue 8:2010
•
RoHS Compliant
•
CE Marked: EN
61000-3-2:2006+A2:2009,
EN 62311:2008, EN 300 328 V1.7.1,
EN 301 489-1, V1.8.1, EN 61000-3-3:2008, EN 301 489-17 V2.1.1, EN301 489-1
V1.9.2), EN 62311:2008
EN60950-1:2006+A11:2009+A1:2010+A12:2011
Electronic Characteristics
Minimum Typical Maximum Unit
Operation voltage 2.35 3.0 3.6 V
Output Power
Sensitivity -92.5
Current Consumption
Dormant mode, VBAT=3V
Deep Sleepmode, VBAT=3V
Idle mode, VBAT=3V
RX/TX active, VBAT=3V
1
16
4.0 dBm
dBm
600 nA
5 uA
mA
mA
4
Firmware Upgrade List
The list below reflects future application firmware that can be loaded into the RB1000 Family
Acronym Description
•
ANP
•
ANS
•
BAS
•
BLP
•
BLS
•
CTS
•
DIS
•
FMP
•
GLP
•
GLS
•
HIDS
•
HOGP
•
HTP
•
HTS
Alert Notification Profile
Alert Notification Service
Battery Service
Blood Pressure Profile
Blood Pressure Service
Current Time Service
Device Information Service
Find Me Profile
Glucose Profile
Glucose Service
HID Service
HID over GATT Profile
Health Thermometer Profile
Health Thermometer Service
•
HRP
•
HRS
•
IAS
•
LLS
•
NDCS
•
PASP
•
PASS
•
PXP
•
RTU S
•
ScPP
•
ScPS
•
TIP
•
TPS
Heart Rate Profile
Heart Rate Service
Immediate Alert Service
Link Loss Service
Next DST Change Service
Phone Alert Status Profile
Phone Alert Status Service
Proximity Profile
Reference Time Update Service
Scan Parameters Profile
Scan Parameters Service
Time Profile
Tx Power Service
5
RB1000/ BPM1000FCE
Model Numbers
Model and Ordering Information
0.57”x 0.99”x 0.12”
RB1000/BPM1000FCE
Bluetooth module with on-board antenna
surface mount, short range
RB1000HM
1.0” x 1.26” x 0.2” dual-in-line, through-hole Bluetooth module.
RB1000 is mounted on Half Inch PCB for DIP (through-hole)
interface to be RB1000HM.
6
RB1000/BPM1000FCE Mechanical Dimensions
Module topside view:
Board size = 14.5 mm x 25.2 mm (0.57” x 0.99”)
Pitch = 1.14 mm (Left & Right side, 0.04”), 1.27mm (Down side, 0.05”)
Pad width = 0.91 mm (0.036”)
7
Loading...