Radiant CD00022, CD00026, CD10035, CD00023, CD10036 Operating And Maintenance Instructions Manual
...
18 In. Wide Cash Drawer Operating and Maintenance Instructions
Application:
Radiant Cash Drawers CD00022, CD00023, CD00026
CD10035, CD10036, CD10194
PARTS AND ACCESSORIES
For cash drawer parts and accessories, contact Radiant Systems.
CAUTION: Breaking coin rolls on the money till may cause the plastic to
fracture.
REMOVING THE INNER DRAWER
GETTING STARTED
Prepare a location for the cash drawer. Recommendations for a suitable location
include:
A sturdy, level surface no less than the size of the cash drawer;
Operating temperature from 32 F to 122 F (0 C to 50 C);
Non-condensing relative humidity from 10% to 95%.
LOCK FUNCTIONS
Two keys are included with each cash drawer for the manual lock. The cash
drawer is shipped in the locked open position. After removing the keys from the
cash drawer, insert them into the lock and turn it to the vertical “on-line” position.
The key lock provides four functions: locked open, manual open, electrically online, and locked closed. To reduce the risk of damaging or breaking the key,
remove the key from the lock during normal operation.
Locked
Closed
Key Number
FIGURE 2
Electrically
On-Line
A
x
x
Manual
Open
Locked
Open
MEDIA STORAGE
The media storage area, located below the till, includes two media trays. The
dividers may be re-positioned into the tray’s grooves to better meet your needs.
FIGURE 3
REPLACING THE INNER DRAWER
Mate the outer slides (mounted to the drawer) with the inner slides (mounted in the
cash drawer housing). Lift the drawer up until it stops, and begin to push the
drawer into the cash drawer housing. When the strike plate on the back of the
drawer has cleared the stop plate in the base, let the drawer rest in the horizontal
position. Push the inner drawer to the fully closed position. You should experience
resistance as you close the drawer sin ce the b all bearin gs d o n o t roll un til the slid es
are fully engaged. When the inner drawer is fully inserted, cycle it a few times to
verify that the drawer opens and closes properly.
PREVENTATIVE MAINTENANCE
The cash drawer slides should be periodically cleaned and lubricated.
Frequency is dependent on use and the environment, but typical
recommended frequency is every three months. Using a dry, lint free
cloth, wipe out the old grease and debris from the inner and outer
slides. Do not use water or any type of liquid cleaner.
Using a clean
applicator, apply a thin layer of lithium-based bearing grease to the
inner and outer slides. Cycle the slides several times to properly coat
the ball bearings and to spread the grease evenly.
Doc no. M-823-296 Rev C
16 In. Wide Cash Drawer Operating and Maintenance Instructions
Application:
Radiant Cash Drawers: CD00024, CD00027
CD10037, CD10193
CAUTION: Breaking coin rolls on the money till may cause the plastic to
fracture.
REMOVING THE INNER DRAWER
FIGURE 1
GETTING STARTED
Prepare a location for the cash drawer. Recommendations for a suitable location
include:
A sturdy, level surface no less than the size of the cash drawer;
Operating temperature from 32 F to 122 F (0 C to 50 C);
Non-condensing relative humidity from 10% to 95%.
LOCK FUNCTIONS
Two keys are included with each cash drawer for the manual lock. The cash
drawer is shipped in the locked open position. After removing the keys from the
cash drawer, insert them into the lock and turn it to the vertical “on-line” position.
The key lock provides four functions: locked open, manual open, electrically online, and locked closed. To reduce the risk of damaging or breaking the key,
remove the key from the lock during normal operation.
Locked
Closed
Key Number
FIGURE 2
Electrically
On-Line
A
x
x
Manual
Open
Locked
Open
MEDIA STORAGE
The media storage area, located below the till, includes one media tray. The divider
may be re-positioned into the tray’s grooves to better meet your needs.
PARTS AND ACCESSORIES
For cash drawer parts and accessories, contact Radiant Systems.
Doc no. M-823-296 Rev C
FIGURE 4
FIGURE 3
ENLARGED SECTION VIEW
Open the drawer and remove the plastic money till. Rotate the swivel pivot stop,
mounted to the back outside surface of the inner drawer, to a horizontal position.
Pull the drawer out.
REPLACING THE INNER DRAWER
Mate the outer slides (mounted to the drawer) with the inner slides (mounted in the
cash drawer housing). Push the drawer in, rotate the swivel pivot stop to a
horizontal position and push the drawer in a few inches. Allow the pivot to swivel
to the vertical position and push the drawer to the fully closed position. You
should experience resistance as you close the drawer since the ball bearings do not
roll until the slides are fully engaged. When the inner drawer is fully inserted,
cycle it a few times to verify that the drawer opens and closes properly.
PREVENTATIVE MAINTENANCE
The cash drawer slides should be periodically cleaned and lubricated. Frequency is
dependent on use and the environment, but typical recommended frequency is
every three months. Using a dry, lint free cloth, wipe out the old grease and debris
from the inner and outer slides. Do not use water or any type of liquid cleaner.
Using a clean applicator, apply a thin layer of lithium-based bearin g grease to the
inner and outer slides. Cycle the slides several times to properly coat the ball
bearings and to spread the grease evenly.
Loading...