Radial Engineering SixPack Rack Adapter User's Guide

Rack mount kit for the SixPack 500 Series Power Frame

Part No. R700 9105 00

Thank you for purchasing the Radial SixPack rack mounting kit. This kit is designed to
allow the SixPack 500 series power frame to be mounted in standard 19” equipment
racks. The kit can also be used for in-desk mounting with a choice of either fl ush or
angled control panel.

The kit is manufactured with 14 gauge steel to protect your SixPack and fi nished in a
tough baked enamel. Elongated slots on the chassis fl ange allow the SixPack to be
adjusted to fi t a range of racks and desks.

Kit contents:

QTY Description Used for

2 Metal rack adapter Adapts the SixPack for 19” rack and in-desk mounting
4 #8-32 screws Phillips machine screws used to fi x the metal rack ears

to the SixPack chassis

www.radialeng.com

5.96”

151mm

Rack mounting the SixPack

For mounting in standard 19” equipment racks, attach the kit to your
SixPack as shown using the included #8-32 machine screws. You may
also need to remove the four rubber feet on the bottom of the SixPack
depending on the available space in your rack. After the kit is attached,
your SixPack will require 4 rack spaces (4RU).

RADIAL ENGINEERING L TD. (“Radial”) warrants this product to be free from defects in material and workmanship and will remedy any such defects free of charge according to the terms of this warranty. Radial will
repair or replace (at its option) any defective component(s) of this product (excluding fi nish and wear and tear on components under normal use) for a period of three (3) years from the original date of purchase. In the
event that a particular product is no longer available, Radial reserves the right to replace the product with a similar product of equal or greater value. In the unlikely event that a defect is uncovered, please call 604­942-1001 or email [e-mail] to obtain an RA number (Return Authorization number) before the 3 year warranty period expires. The product must be returned prepaid in the original shipping container
(or equivalent) to Radial or to an authorized Radial repair center and you must assume the risk of loss or damage. A copy of the original invoice showing date of purchase and the dealer name must accompany any
request for work to be performed under this limited and transferable warranty. This warranty shall not apply if the product has been damaged due to abuse, misuse, misapplication, accident or as a result of service
or modifi cation by any other than an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE HEREOF AND DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE
OF THREE YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE OF THIS PRODUCT. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.

THREE YEAR TRANSFERABLE LIMITED WARRANTY

1.53”

39mm

3.53”

90mm

Radial Engineering Ltd. 1588 Kebet Way, Port Coquitlam BC V3C 5M5 • Phone: [phone] • Fax: [phone] • Email: [e-mail]

Radial® SixPack™ Rackmount Kit User Guide - Part #R870 1264 00 •

Specifi cations and appearance are subject to change without notice. © Copyright 2013, all rights reserved.

Flush In-Desk mounting the SixPack

For fl ush in-desk mounting, attach the kit to your SixPack as shown using the
included #8-32 machine screws. The elongated slots on the fl ange allow the SixPack
to be positioned fl ush with the desktop. The kit is compatible with desks up to 1.5
inches (39mm) in thickness.

Before mounting, ensure there is enough space under the desk to accommodate
the SixPack chassis plus an extra 6” (150mm) of space for the rear panel cable
connections. Use a pencil and mark the cut-out area that needs to be removed on the
desk. Mount the SixPack from below the desk surface using hardware appropriate
for the desk material.

12.2”

(31cm)

CUT-OUT AREA

6.1”

(15.5cm)

FRONT EDGE

Angled In-Desk mounting the SixPack

For angled in-desk mounting, attach the kit to your SixPack as shown using the
included #8-32 machine screws. After the kit is attached the SixPack chassis will be
positioned at a 45° angle. The elongated slots on the fl ange allow the SixPack to be
positioned fl ush with the desktop. The kit is compatible with desks up to 1.5 inches
(39mm) in thickness.

Before mounting, ensure there is enough space under the desk to accommodate
the SixPack chassis and an extra 6” (150mm) of space for the rear panel cable
connections. Use a pencil and mark the cut-out area that needs to be removed on the
desk. Mount the SixPack from below the desk surface using hardware appropriate
for the desk material.

12.2”

(31cm)

CUT-OUT AREA

9.7”

(24.6cm)

FRONT EDGE

true to the music

www.radialeng.com

Radial Engineering Ltd. 1588 Kebet Way, Port Coquitlam BC V3C 5M5 • Phone: [phone] • Fax: [phone] • Email: [e-mail]

Specifi cations and appearance are subject to change without notice. © Copyright 2013, all rights reserved.