Radial Engineering DiNet Dan-RX User's Guide

®

True to the Music™

™

DAN-RX

2-Ch Dante® Receiver

User Guide

Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam
British Columbia, Canada, V3C 5M5

Tel: [phone] • Fax: [phone]

Email: [e-mail]

www.radialeng.com

Note: This device has been tested and found to comply with the limits
for a Class A digital device, according to Part 15 of the FCC Rules and

EN55022. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a commercial environ­ment. This device generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the user manual, may cause harmful
interference to radio communications. Operation of this device in a residential area
is likely to cause harmful interference, in which case the user will be required to
correct the interference at their own expense.

Radial® DAN-RX™ User Guide

Table of Contents Page

Features ................................................................................... 1-2

Overview.......................................................................................3

Getting Started .............................................................................4

Making Connections .....................................................................5

Using the Headphone Amplier ....................................................6

Block Diagram ..............................................................................7

Specications ...............................................................................8

Warranty .......................................................................Back cover

Congratulations on purchasing the Radial DiNET DAN-RX™!
The DAN-RX is a high-resolution digital-to-analog converter that
is designed to connect to a Dante-enabled Ethernet network —
seamlessly transferring the audio stream to a pair of balanced
audio outputs to feed a PA, recording device or broadcast mixing
console.

This manual covers the setup and operation of the DAN-RX in
various applications. Please take a few minutes to read through
and familiarize yourself with the DAN-RX features and functions.
If you have any questions that are not covered in this manual,
please consult the FAQ section on our website. This is where

we post the latest updates. If you still do not nd what you are

looking for, feel free to send us an email at [e-mail]
and we will do our best to reply in short order.

FEATURES

® ®

True to the Music True to the Music

1

2 3

4

1. HEADPHONE: Sets output level of the headphone ampli er. Mini

3.5mm (1/8”) TRS headphone output. Works with earbuds and
standard headphones.

2. SYNC LEDs: Red LED is illuminated when unit is powered. Green
LED will illuminate once connected to an Ethernet network. Flashing
green LED indicates that the DAN-RX is in master clock mode, solid
green LED indicates that it is in slave mode.

3. ETHERNET PORT: Connects to the Dante network via standard
CAT5e or CAT6 Ethernet cable. This port delivers the digital audio
signal from the network and powers the DAN-RX when Power over
Ethernet (PoE) is available.

4. SYS LEDs: Red LED illuminates when power is  rst applied.

Switches to green LED once Dante processor becomes active.

5. +15V LED: Will illuminate
when the DAN-RX is receiving
power via the included DC
power adapter.

6. PoE LED: Will illuminate when
the DAN-RX is receiving Power

5 6

over Ethernet (PoE).

7 8 10

9

7. LEFT AND RIGHT XLR OUT: Balanced analog audio outputs.
Output level is controlled by audio playback source.

8. POWER: 15VDC connection for use with included Radial power
adapter.

9. CABLE CLAMP: Used to secure the power supply cable (when
used) to prevent accidental disconnection.

10. NO SLIP PAD: Provides electrical and mechanical isolation and
keeps the DAN-RX from sliding around.

11. GROUND LIFT: Lifts pin-1 on
both XLR outputs to eliminate
buzz and hum from ground
loops. Move the switch to the
right (towards the Ethernet
input) to lift the ground.

11

Radial Engineering Ltd.

1 2

DiNET DAN-RX™

Radial Engineering Ltd.

DiNET DAN-RX™

® ®

True to the Music True to the Music

OVERVIEW

The Radial DiNET DAN-RX is a professional grade digital-to-analog audio

converter designed speci cally for use with Dante-enabled networks.

It allows you to create a stereo audio endpoint at any location within a
Dante network, featuring an Ethernet connector to receive the digital
signal, and balanced analog outputs to feed mixing consoles, power

ampli ers, or self-powered speakers.

High quality 24bit/96kHz converters provide pristine audio and ensure
that the digital source content is reproduced as faithfully as possible,
and a rugged 14-gauge steel chassis with a bookend design protects
the connectors from damage. The DAN-RX also features a built-in

headphone ampli er with an adjustable level control, allowing you to

easily check the audio signals, or feed a monitor mix to any destination.

Dante Network

Cat 5e / Cat6

The DAN-RX is easy to use, with no setup required on the device itself.

It is completely con gured by Dante Controller, which manages digital

audio routing across the Dante network. Dante Controller is a software
application by Audinate™ that allows the user to manage all Dante­enabled devices across a network. Use Dante Controller to route audio
to the DAN-RX and all other components on the network. Simply plug the
DAN-RX into the network and it will automatically appear as an available
output device within Dante Controller. The DAN-RX will initially have
the name “DiNET-RX-xxxxxx”, where the last 6 digits will be the unique
media access control address (MAC address) of your DAN-RX. As this
can be changed to a user-generated name using Dante Controller, we
recommend writing down the MAC address of your unit in the space
provided below for future reference.

GETTING STARTED

Before making any connections, always ensure your ampli ers or

speakers are either turned down or turned off in order to protect sensitive
components from damage due to loud transients that can occur when
plugging in or turning on various components.

POWERING THE DAN-RX

PoE

Power for the DAN-RX can be provided via
power over ethernet (PoE) from a PoE­capable network switch or a separate PoE

injector. Once power is available, the side

panel PoE LED indicator will illuminate and
the DAN-RX will be ready to use.

Power Supply

The included 15VDC power supply is provided
for use when PoE is not available. Once you
have connected the DAN-RX to the Ethernet
switch, plug in the power supply. The side
panel +15VDC LED will illuminate and the
DAN-RX will be ready to use.

As a backup option, the DAN-RX is designed to be able to have both PoE
and the 15VDC adaptor connected at the same time. If one fails, the other
will maintain power without switch-over noise.

ETHERNET CONNECTION

The DAN-RX connects to the Ethernet switch using a standard CAT5e
or CAT6 cable. Once the Ethernet switch is connected to a computer
running the Dante Controller software, the DAN-RX will appear as an
available receive device.

Dante Network

Record your DAN-RX MAC address here:

DiNET-RX-__________________

Dante Controller can be downloaded for free at www.audinate.com. For

latest  rmware for the DAN-RX please visit www.radialeng.com.

Radial Engineering Ltd.

3

DiNET DAN-RX™

Radial Engineering Ltd.

4

DiNET DAN-RX™

® ®

True to the Music True to the Music

MAKING CONNECTIONS

Connect two standard low-impedance XLR cables from the LEFT and
RIGHT outputs to the inputs of your PA or recording system. These XLR
outputs conform to the AES standard and are balanced to drive long
cable runs up to 100 meters (300’) without noise, and are suitable for
connecting the DAN-RX to professional mixing consoles, preamps and

power ampli ers. The signal level at these outputs is controlled by the

audio playback source.

Right

Left

Audio connections for PA system and recording systems use

balanced XLR cables up to 100 meters (300’).

IMPORTANT NOTE: The DAN-RX does not require phantom power to
operate. The DAN-RX is equipped with blocking capacitors to prevent
damage from DC voltage, but for best results please ensure that the
phantom power is switched off when connecting to the microphone
input of a mixer.

USING THE HEADPHONE AMPLIFIER

The DAN-RX is equipped with a dedicated stereo headphone output. The

3.5mm (1/8”) output is designed for both ear buds and standard TRS
stereo headphones wired tip-left, ring-right and the sleeve is ground. The
volume control on the DAN-RX affects the headphone output only, as it
is designed for testing purposes rather than setting the level of the XLR
outputs.

Be careful! The DAN-RX is designed for professional use. The headphone

ampli er is very powerful and is capable of high sound levels that could

damage your hearing. Always ensure the volume control is set to its
lowest point (fully counter-clockwise) when plugging in headphones, and
slowly increase the level to a satisfactory level. If no signal is present,
ensure that audio is routed to the unit via the Dante Controller software.

Not all headphones are created equally! Always start at the lowest
volume when switching headphones. While the DAN-RX is designed
to work with headphones of all different impedances, volume level can
change drastically from pair to pair.

Radial Engineering Ltd.

Headphone Safety Warning

Caution: Very Loud Amplifi er

As with all products capable of producing high sound pressure levels (SPL), users
must be very careful to avoid the hearing damage that may occur from prolonged
exposure. This is particularly important when applied to headphones, as prolonged
listening at high SPL’s will eventually cause tinnitus and can lead to partial or complete
loss of hearing. Please be aware of the recommended exposure limits within your

jurisdiction and follow them closely. The user agrees that Radial Engineering Ltd is

not liable for any health effects resulting from the use of this product and the user
clearly understands that he or she is entirely responsible for the safe and proper use
of this product. Please consult the Radial Limited Warranty for further details.

5

DiNET DAN-RX™

Radial Engineering Ltd.

6

DiNET DAN-RX™

® ®

True to the Music True to the Music

BLOCK DIAGRAM*

OUTPUT LEFT

PHANTOM

DC BLOCK

PHASE

BUFFER

SPLITTER/

LIFT

GROUND

OUTPUT RIGHT

CHASSIS_GND

PHANTOM

DC BLOCK

PHASE

BUFFER

SPLITTER/

OUTPUT

HEADPHONE

H/P

AMPLIFIER

SPECIFICATIONS*

Audio Circuit Type: ............................................High current balanced active output device

Number of Channels: .........................................2

Sample Rate: .....................................................44.1kHz, 48kHz, 88.2kHz, and 96kHz

Bit Depth: ...........................................................24 bit

Frequency Response: ......................................20Hz-20kHz

Idle Channel Noise: ...........................................-108dB

Dynamic Range: ...............................................>100dB

Channel Separation: ..........................................>75dB

Gain: ..................................................................8dBu max @ 0dBfs

Total Harmonic Distortion + Noise: ....................0.007% @ -6dBfs

Output Impedance: ............................................150Ω

Power Consumption: .........................................1.25W

Features

Input Connections: .............................................RJ45 Ethernet

Output Connectors: ...........................................2x XLR male, 1x 3.5mm headphone out

LED Indicators: ..................................................SYNC, SYS, +15V, and PoE

Extras: ...............................................................Headphone amplier with level control

General

Power: ...............................................................15VDC 400mA (included) or PoE

Power over Ethernet (PoE) ................................Class 1 IEEE 802.3af

FCC Approval: ...................................................Meets FCC Part 15B Class A

Construction: .....................................................14-gauge steel

Finish: ................................................................Durable powder coat

Warranty: ..........................................................Radial 3-year, transferable

* Subject to change without notice.

Radial Engineering Ltd.

FILTER

CPU/

CODEC

PHY

DANTE

ETHERNET

FILTER

CPU/

CODEC

* Subject to change without notice.

7

DiNET DAN-RX™

Radial Engineering Ltd.

8

DiNET DAN-RX™

THREE YEAR TRANSFERABLE LIMITED WARRANTY

RADIAL ENGINEERING LTD. (“Radial”) warrants this product to be free from defects in
material and workmanship and will remedy any such defects free of charge according
to the terms of this warranty. Radial will repair or replace (at its option) any defective

component(s) of this product (excluding  nish and wear and tear on components under

normal use) for a period of three (3) years from the original date of purchase. In the event
that a particular product is no longer available, Radial reserves the right to replace the
product with a similar product of equal or greater value. In the unlikely event that a defect
is uncovered, please call 604-942-1001 or email [e-mail] to obtain an

RA number (Return Authorization number) before the 3 year warranty period expires.

The product must be returned prepaid in the original shipping container (or equivalent)
to Radial or to an authorized Radial repair centre and you must assume the risk of loss
or damage. A copy of the original invoice showing date of purchase and the dealer name
must accompany any request for work to be performed under this limited and transferable
warranty. This warranty shall not apply if the product has been damaged due to abuse,

misuse, misapplication, accident or as a result of service or modi cation by any other than

an authorized Radial repair center.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE FACE
HEREOF AND DESCRIBED ABOVE. NO WARRANTIES WHETHER EXPRESSED
OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL EXTEND
BEYOND THE RESPECTIVE WARRANTY PERIOD DESCRIBED ABOVE OF THREE
YEARS. RADIAL SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING FROM THE USE
OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND

YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY DEPENDING ON WHERE
YOU LIVE AND WHERE THE PRODUCT WAS PURCHASED.

To meet the requirements of California Proposition 65, it is our responsibility to inform you of the following:

WARNING: This product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.

Please take proper care when handling and consult local government regulations before discarding.

®

www.radialeng.com

Radial Engineering Ltd.
1588 Kebet Way, Port Coquitlam, British Columbia, V3C 5M5

Tel: [phone] • Fax: [phone] • Email: [e-mail]

Radial® DAN-RX™ User Guide - Part #: R870 1033 00 / 06-2017
Copyright 2017 Radial Engineering Ltd. All rights reserved.

Speci cations and appearance subject to change without notice.