Rack It WALL Instructions Manual

TOOLS REQUIRED: Phillips Head

WALL

1 x Rack It WALL Hang Track 1029MM

1 x Rack It WALL Bracket

Screwdriver, Stud Finder,Electric
Drill, Rubber Mallet (or a Hammer
– gently does it), Pencil, Spirit
Level

RACK IT

900mm ADD ON KIT

ASSEMBLY INSTRUCTIONS

ITEM CODE: 01804

WARNING: HANDLE CUT METAL

EDGES CAREFULLY

SAFETY TIP

When assembling or installing this product
wear protective gloves and eyewear

YOUR HEADACHE-FREE GUIDE TO RACK IT LIKE A BOSS

You’ve got this! We know because you take pride in your passions. Take care of your stuff. That’s why you purchased this Rack It WALL
Add On Kit. You’re particular. And we like that. Because we know you’ll take the time to check off all the Parts listed below and to read
through these Assembly Instructions before you start. Cue Farnsey (or Beyoncé – whatever lifts you). Let’s do this

PARTS LIST:

10 x Self Tapping Screws

Includes Plaster Board and

Dyna Bolt fixings

1 x Rack It WALL Hang Track 1029MM

1 x Rack It WALL Bracket

2 x Rack It WALL Beam 949MM

2 x Rack It WALL Double Slot WALL Strips 1029MM

STAGE 1: TRACK IT

Pick a wall. Not just any wall. The wall next to your existing Rack It
WALL Unit. Grab your trusty Stud Finder (meep-meep) and a

STEP 1 STEP 2

Pencil, and find and mark at least 1x stud in line with your existing
WALL Unit’s Hang Track. Place your new Hang Track on the wall next to your existing
Wall Unit’s Hang Track, and use your Spirit Level to (you guessed it) check
your Track is level with your existing Unit. Mark all the screw
positions with your Pencil (making sure at least 1 of
them is over a stud), then your Spirit Level
can knock off for the day.

For the screw positions that don’t hit

For the screw positions that don’t hit
studs, insert Plasterboard Anchors by

studs, insert Plasterboard Anchors by
pushing them into the plasterboard and

pushing them into the plasterboard and
tighten with your Screwdriver. Secure the Hang Track by

tighten with your Screwdriver. Secure the Hang Track by
inserting Screws through the Screw Holes into the

inserting Screws through the Screw Holes into the
Plasterboard Anchors and tighten by hand. For the

Plasterboard Anchors and tighten by hand. For the
Screw that hits the stud, you’ll need to use an

Screw that hits the stud, you’ll need to use an
Electric Drill.

Electric Drill.

1 x Rack It WALL Wire Shelf 900 X 600MM

2 x Shelf Support Brace 612MM

STEP 1

You’ll need to unload
your precious stuff off
your existing WALL Unit
for now, and disassemble
that Unit to allow room
for your Add On Kit’s
Back Beam to be
attached. Don’t be sad,
it’s for the greater good.
Hang your WALL Strip
off the floating end of
the Hang Track (as
shown) – you’ll use the
WALL Strip of your
adjacent existing WALL
Unit at the other end.
We planned ahead.

STAGE 2: HANG IT

STEP 2

Attach a Back Beam to the back of the Wall Strips at your
desired height. Gently does it here, as your new Wall Strip isn’t
yet fixed to the wall. Tap into place with a Rubber Mallet
(or gently with a Hammer).

MADE IN CHINA | DISTRIBUTED BY:
Zenexus (AUS) Ph. 1300 734 714 Zenexus (NZ) Ph. 0800 443 058

AUSTRALIA: RACK-IT.COM.AU NEW ZEALAND: RACK-IT.CO.NZ

RACK IT

WALL

900mm ADD ON KIT

ASSEMBLY INSTRUCTIONS

ITEM CODE: 01804

TOOLS REQUIRED: Phillips Head

Screwdriver, Stud Finder,Electric
Drill, Rubber Mallet (or a Hammer
– gently does it), Pencil, Spirit
Level

WARNING: HANDLE CUT METAL
EDGES CAREFULLY

SAFETY TIP

When assembling or installing this product
wear protective gloves and eyewear

Use your Pencil to mark the screw points of your new WALL
Strip. Then remove your new WALL Strip from your Hang Track

STEP 3

so you can insert Plasterboard Anchors into the screw spots. Put
your WALL Strip back on the Hang Track (take a second here to check the Screw
Holes line up with your Plasterboard Anchors) and Screw this badboy onto the wall.

STAGE 3: RACK IT

STEP 1

Reattach your Bracket to the
Hang Track of your original
Wall Unit so that the top of
the Bracket lines up with the
Back Beam. Then hook your
Add On Bracket onto the
new Wall Strip (as shown) so
that it lines up with the
others. Tap tap with your
Rubber Mallet or Hammer
(gently does it). Fix both
Brackets off with the Screws
provided.

STEP 2

Hook your Front Beams onto your
Brackets. Tap tap with your Rubber
Mallet or Hammer (gently does it)
and fix in place with the Screws
provided.

STEP 4

Once you’re happy with the
height and that all the
Brackets, Braces and Beams
are in place, lay your Wire
Shelf on top and, voila! Your
Rack It 900mm Wall Add On
Kit is done.

STEP 3

Slide all of your Support
Braces into place: one end in
the Front Beam and one in
the Back Beam.

You’ve done it! Cue warm
inner feeling of satisfaction.

Stand back and marvel at
your Rack It 900mm WALL
Add On Kit. Now all that’s
left to do is stack up to
100kg of your precious stuff
on top (alongside the 100kg
of precious stuff on your
original Wall Unit). Now is
also the time to enjoy
tossing these instructions in
the recycling.

And, don’t forget, if you love your new, new Wall Unit so much you just want to store even more of your best stuff up top, you can
always add on another Add On Kit, before you get carried away and overload this one. We knew you had it in you!

MADE IN CHINA | DISTRIBUTED BY:
Zenexus (AUS) Ph. 1300 734 714 Zenexus (NZ) Ph. 0800 443 058

AUSTRALIA: RACK-IT.COM.AU NEW ZEALAND: RACK-IT.CO.NZ