RACK-IT 3 WIRE SHELF KIT ASSEMBLY INSTRUCTIONS

3 WIRE SHELF KIT

TOOLS REQUIRED: Rubber Mallet
(or a Hammer – gently does it)

ASSEMBLY INSTRUCTIONS

ITEM CODE: 01810

1938W X 1830H X 640mm D

SAFETY FIRST

strongly recommend you fix this Kit permanently to the ground or a wall. Because we don’t know what your ground or walls look like, we don’t include
the fixing devices. If you’re unsure what to use, ask a professional.

This Kit is fitted with a Ground Mounting Bracket to stop it doing anything crazy, like toppling over. On you, or someone you love. We

WARNING: HANDLE CUT METAL
EDGES CAREFULLY

SAFETY TIP

When assembling or installing this product
wear protective gloves and eyewear

YOUR HEADACHE-FREE GUIDE TO RACK IT LIKE A BOSS

You’ve got this! We know because you take pride in your passions. Take care of your stu. That’s why you purchased this Rack It 3 Wire
Shelf Starter Kit. You’re particular. And we like that. Because we know you’ll take the time to check o all the Parts listed below and to
read through these Assembly Instructions before you start. Cue Farnsey (or Beyoncé – whatever lifts you). Let’s get this Starter Kit started.

PARTS LIST:

6 X 1872MM BEAMS

12 X SHELF SUPPORT BRACES

12 X

SAFETY

PINS

6 X WIRE SHELVES (896 W X 500MM D)

STEP 1 STEP 2

Find a flat area near where you want your
Kit to end up. This is your work area. Kick
any clutter into another corner. Grab a friend
or family member/helper and stand up both
Uprights about 1800mm (roughly a human
length) apart.

Insert your first Beam into the Slots at the
back of 1x Upright. Then (you guessed it) do
the same again on the other side. Once both
sides are slotted in, gently tap-tap into place
with your Mallet.

2 X UPRIGHTS (1830 H X 630MM D)

STEP 3

Repeat Step 2, this time on the front
of your Kit.

Hot tip:

Count the number of Slots up from the ground,
so all of your Beams are the same heights and
you don’t need to find a Spirit Level.

STEP 4

Slide 4x Shelf Support Braces into the holes
on your Bottom Beams (pay attention to the
image detail here – you’ll thank us later).

STEP 5 STEP 6

Repeat the Beaming and Bracing process for
your Middle Shelf and Top Shelf.

Add a Safety Pin to each Beam–Upright
junction. Place your Wire Shelves on top of
your Braces and, viola! Your Rack It 3 Wire
Shelf Starter Kit Unit is complete.

Hot tip:

Count the number of Slots up from the
ground, so all of your Beams are the same heights
and you (still) don’t need to find a Spirit Level.

Congratulations: you have now graduated to the level of Storage Beast. Stand back and marvel at your Rack It 3 Wire Shelf Starter Kit. Don’t forget, fix it permanently to the ground or a wall,

to stop it doing anything crazy, like toppling over. Now is the time to enjoy tossing these instructions in the recycling.And remember, if you love your new shelving Kit so much you just want to store even
more of your best stu up top, you can always add on another Kit, before you get carried away and overload this one.

MADE IN CHINA | DISTRIBUTED BY:
Zenexus (AUS) Ph. 1300 734 714 Zenexus (NZ) Ph. 0800 443 058

AUSTRALIA: RACK-IT.COM.AU NEW ZEALAND: RACK-IT.CO.NZ

Hot tip:

If your Safety Pin holes aren’t lined up properly, the Pins
won’t slide in. A little tap-tap with your Mallet or
Hammer will be enough to seat the joins, if required.

We knew you had it in you!