RAB Lighting YBLED 3 pin PCT, YBLED 5 pin PCT, YBLED LC, YBLED Button PC Installation Instructions Manual
Page 1
YBLED 40W-60W INSTALLATION INSTRUCTIONS
®
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
YBLED Button PC
YBLED 3 pin PCT
YBLED 5 pin PCT
YBLED LC
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for
safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture.
LOCATION
Select a location on a structurally sound, at wall or pole. Fixture should be located on wall or pole at least 18” below any overhang
or other structural detail. Fixture must not be recessed.
MOUNTING TO WALL
1. Secure the xture to a sturdy wall. Using the mounting
arm as a guide, mark the 3 mounting holes. Drill 3/16”
pilot holes and use provided Lag Bolts (3) to mount to
wooden surface or use appropriate mounting hardware
(not supplied) suitable for the mounting surface.
2. Install the 2 bottom Lag Bolts rst. Screw in the Lag
Bolts so that there is about 3/8” of space under the
head.
3. Place the xture on these 2 bottom Lag Bolts. Install
the top Lag Bolt then tighten the other 2 bolts.
4. Loosen screw and remove the Arm Cover.
5. Knock out the appropriate Conduit Knockout on the
Arm Cover to route input conduit. Use appropriate
conduit connectors as required by code. Connect wires
as shown in wiring diagram. Push all wires back into the
Housing Arm. Be careful not to pinch wires.
6. Secure the Arm Cover and tighten screw.
7. Apply weatherproof silicone sealant around the edge
of the Housing Arm and the wall. This is especially
important with an uneven wall surface.
YARM24 MOUNTING
1. Secure the Interlocking Mounting Clamps around the
YARM24 using the provided truss screws, locknuts and
hex-nuts.
2. Mount the YARM24 to a sturdy wall. Using the YARM24
mounting plate as a guide, mark the 4 mounting holes.
Drill 3/16” pilot holes and use provided Lag Bolts (4) to
mount to wooden surface or use appropriate mounting
hardware (not supplied) suitable for the mounting
surface.
3. Remove the Arm Cover by loosening the screw. Remove
the Clamp by loosening the 2 screws on the Clamp.
4. Knock out the arm-entry knockout on the Arm Cover.
Secure the YARM24 and the Clamp in the Housing Arm
and tighten the clamp screws.
5. Knot wires in YARM24 for strain relief and feed wires
from the YARM24 into the Housing Arm. Make the
necessary wiring connections in the Housing Arm.
Connect wires as shown in wiring diagram. Push all wires
back into the Housing Arm. Be careful not to pinch
wires.
6. Secure Arm Cover and tighten the screw.
Housing Arm
Lag Bolts (3)
Conduit Knockout
Arm Cover
Housing Arm
Arm Cover
Clamp
YARM24
Interlocking Mounting Clamps
Lag Bolts (4)
Page 2
YBLED 40W-60W INSTALLATION INSTRUCTIONS
®
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
WIRING
Universal voltage driver permits operation at 120V to 277VAC,
50 - 60 Hz.
1. Connect the bare copper Ground wire from xture to
supply ground.
2. Connect the BLACK xture lead to the LINE supply lead.
3. Connect the WHITE xture lead to the COMMON supply
lead.
ACCESSORIES
24” Yardblaster Arm: YARM24
TROUBLESHOOTING
1. Check that the line voltage at the xture is correct. Refer
to wiring directions.
2. Be sure xture is grounded properly.
3. Be sure the photocell is functioning properly?
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough
to touch. Do not clean or maintain while xture is
energized.
1. Clean polycarbonate refractor with non-abrasive
cleaning solution.
2. Do not open the xture to clean the LED. Do not touch
the LED.
Pat: D 713019
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Easy Answers
© 2017 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
YBLED-IN-1217
rabweb.com
Visit our we bsite for produc t info
Tech Help Line
Call our ex perts - 888 722-1000
e-mail
Answered promptly - sales@rabweb.com
Free Lighting Layouts
Answered o nline or by reques t
Loading...