RAB Lighting Yard Blaster Series Installation Instructions Manual

YARD BLASTER INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting
fixtures. Our aim is to design the
best quality products to get the job
done right. We’d like to hear your
comments. Call the Marketing
Department at 888.RAB-1000, or
email: [e-mail]

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. This product must be installed in accordance with the applicable installation code by
a person familiar with the construction and operation of the product and the hazards involved.The YardBlaster is for
outdoor use and should not be used in areas with limited ventilation or high ambient temperatures.

WARNING: Make certain power is OFF before installing or maintaining fixture.

LOCATION

Select a location on a structurally sound, flat wall or pole
10-25 feet from the ground. Fixture should be located on
wall or pole at least 18” below any overhang or other
structural detail.

Fixture should not be recessed.

MOUNTING

Wall Mounting

1. Using the mounting template as a guide, mark the 3
mounting holes. We suggest drilling 3/16” pilot holes
for lag screws (not provided).

2. Install the 2 bottom lag screws first. Screw in the lag
screws so that there is about 3/8” of space under the
head.

3. Place the fixutre on these 2 bottom lag screws. Install
the top lag screw then tighten the other 2 screws.

4. Secure the outdoor cable or flexible conduit to the
cover plate with a fitting in accordance with the
National Electric Code.

5. Install the coverplate and secure with the 2 screws
and nuts provided.

6. Install the reflector/lens assembly. Secure with the 2
screws and washers provided.

7. Install correct lamp provided.

YLM_YLS-IN-1210

YARD BLASTER INSTALLATION INSTRUCTIONS

WIRING

CAUTION: Check that voltage is compatible with fixture ballast.

1. Thread the black and white wires through the hole in the
cover plate as shown.

2. Connect the black fixture lead to the black supply lead.

3. Connect the white fixture lead to the white supply lead.

4. Green fixture ground screw must be connected to the
supply ground.

PHOTOEYE INSTALLATION

1. Loosen the screw in the center of the photocontrol
socket 2 turns. Twist the socket so the arrow points
North. Note: There is a stop to prevent the socket
from turning all the way around. If you have trouble
turning the socket try turning it in the opposite direction.
Retighten the screw in the socket.

2. Align the photocontrol (it will only plug in one way).
Plug in and twist clockwise until it stops.

RE-LAMPING

CAUTION: Prior to installing, check that the lamp is of
proper type and wattage. Observe lamp manufacturer’s
recommendations on lamp operation, ballast type and
burning positions. Be sure power is OFF.

1. Remove front housing following instructions under
Mounting section.

2. Remove old lamp by unscrewing counterclockwise.

3. Place lamp into lamp socket and screw lamp securely
into lamp socket until it is firmly seated.

4. Replace front housing.

CLEANING

CAUTION: Be sure fixture temperature is cool enough to
touch. Be sure power is OFF.

Clean reflector and front housing with mild soap or household­type detergent. Do not use acid, ammonia or any other
caustic solvent-based cleaners.

TROUBLESHOOTING CHECKLIST

Check that:

1. Proper lamp is installed. Lamp is not faulty.

2. Line voltage at the fixture is proper.

3. Fixture is wired properly.

4. Fixture is grounded properly.

Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.

YLM_YLS-IN-1210

RAB fixture designs are protected under
U.S. and International Intellectual Property laws.
Patent pending.