RAB Lighting WPLED 78W series, WPLED2T78 Cool, WPLED3T78 Cool, WPLED4T78 Cool, WPLED2T78 Neutral Installation Instructions Manual

®

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting fi xtures.
Our goal is to design the best quality
products to get the job done right. We’d like
to hear your comments. Call the Marketing
Department at 888-RAB-1000, or email:
[e-mail]

IMPORTANT

READ CAREFULL Y BEFORE INST ALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB fi xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. This product must be installed in accordance with the applicable installation code by a
person familiar with the construction and operation of the product and the hazards involved.

WARNING: Make certain power is OFF before installing or maintaining fi xture. No user servicable parts

inside.

MOUNTING ARM ON FIXTURE

1. Remove the Arm Cover from the Arm.

2. Feed wires from Fixture through Gasket into Arm.

Fixture

Gasket

Arm

3. Line up Arm and Fixture. Place fl at washers, lock
washers and nuts on the 3/8-16” bolts inside the Arm
and tighten securely to housing.

4. Make sure the Gasket is secure between Arm and
Fixture.

MOUNTING FIXTURE ON WALL

1. Separate Wall Mount Cover and Wall Mount Box.

2. Orient box so that “TOP” is on top.

3. Secure Wall Mount Box to a sturdy wall. Use
appropriate mounting hardware such as lag bolts and
anchors with washers suitable for the mounting sur­face. Use weatherproof silicone sealant between wall
and Wall Mount Box.

4. Feed supply wires through Wall Mount Box, Gasket,

and Wall Mount Cover.

5. Check that Gasket between Wall Mount Box and
Wall Mount Cover is secure and screw the cover on

box using four screws.

6. Line up Arm and Wall Mount Cover. Place fl at wash-
ers, lock washers and 3/8-16 bolts from wall bracket
(do not use long bolts provided with Arm), inside the
Arm and tighten securely.

7. Feed wires through the Arm Gasket into Arm. Make
necessary connections in the Arm.

8. Replace the Arm Cover. Be sure Gasket on Arm

Cover is in place.

Arm Cover

Arm

Gasket

Plugs

Plugs

Arm Gasket

3/8-16 bolts

Screws

Wall Mount
Cover

Tether

3/8” bolts

Gasket

Wall Mount Box

Plugs (4)

9. Tighten Close Up Plugs and apply weatherproof
silicone sealant to all unused conduit entry points.
Also use sealant between the wall and Wall
Mount Box.

Page 1

®

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS

WALL MOUNT BOX DETAILS

4.57”

Key Hole Slot

2.4”

1.09”

3.0”

Wall Feed

.79”

Hardware
(not supplied)

Conduit Feed

TROUBLESHOOTING

1. Check that the line voltage at fi xture is correct. Refer

to wiring directions.

2. Is the fi xture grounded properly?

3. Is the photocell functioning properly (if used)?

WIRING

Universal voltage driver permits operation at 120 to
277VAC, 50 or 60Hz.

1. Connect the black fi xture lead to the (+) LINE
supply lead.

2. Connect the white fi xture lead to the (-) COMMON
supply lead.

3. Connect the bare copper Ground wire from fi xture to
supply ground.

-*/& #-"$,

$0..0/ 8)*5&

-*()5

'*9563&

(306/% (306/%

CLEANING & MAINTENANCE

CAUTION: Be sure fi xture temperature is cool
enough to touch. Do not clean or maintain while
fi xture is energized.

1. Clean glass lens with non-abrasive glass cleaning
solution.

2. Do not open fi xture to clean the LED. Do not touch
the LED.

RAB fi xture designs are protected under
U.S. and International Intellectual Property laws.
Patent pending.

Page 2

®

WPLEDTM 78W WALL MOUNT INSTALLATION INSTRUCTIONS

WPLED2T78 Cool

WPLED3T78 Cool WPLED4T78 Cool

WPLED2T78 Neutral

WPLED3T78 Neutral WPLED4T78 Neutral

WPLED78 IN 1011

Page 3