Page 1
10W LED WALLPACK INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting
xtures. Our goal is to design the
best quality products to get the job
done right. We’d like to hear your
comments. Call the Marketing
Department at 888-RAB-1000, or
email: marketing@rabweb.com
WPLED10
Junction Box
WPLED10S
Surface Mount
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable
parts inside.
JUNCTION bOx MOUNT fOR
CONDUIT
For use on retrot applications that make conduit
necessary.
Loosen and remove (3) Lens Screws. Remove
1.
Door.
Loosen and remove (2) Housing Screws. Remove
2.
Housing from Back Box. Keep Gasket intact for
re-assembly.
Secure Back Box to the mounting surface using
3.
hardware appropriate for that mounting surface.
Wire the xture using UL approved wire connectors
4.
and according to NEC and local codes. Apply
sealant to all unused conduit entry points.
Place Gasket between Back Box and Housing.
5.
Re-mount Housing to Back Box. Check Gasket
seal all around the Back Box.
Re-mount Door to Housing. Tighten (3) Lens
6.
Screws. Check Door gasket seal.
SURfACE MOUNT fOR
RECESSED bOx
For use with recessed junction box and wiring.
Use supplied crossbar. Mount Crossbar to recessed
1.
junction box with (2) screws.
Place Gasket on back of the xture. Gasket should
2.
create seal against mounting surface.
Wire xture to supply wires in recessed box according
3.
to wiring section.
Use 1/4 x 20 stainless steel Mounting Screw to
4.
attach xture to Crossbar. Tighten Mounting Screw.
Cover screw with Cap, provided.
5.
Fixture can be mounted upside down in dry and damp
6.
locations only.
Crossbar
Gasket
7.
Back Box
Fixture can be mounted upside down in dry and
damp locations only.
Gasket
Lens
Screws
Housing
Housing
Screws
Door
Cap
Mounting
Screw
Recessed
Junction
Box
Page 2
10W LED WALLPACK INSTALLATION INSTRUCTIONS
-*()5
'*9563&
-*/& #-"$,
$0..0/ 8)*5&
(306/%
(306/%
JUNCTION bOx
The Junction box has (4) conduit entry points
1.
on the center of each side and (1) in the center
back.
Mounting points are dimensioned below.
2.
4 3/4”
1 1/8”
2 3/16”
3 1/2”
WIRING
All units are factory wired for 120V.
Connect the black xture lead to the (+) LINE
1.
supply lead.
1 1/8”
TROUbLESHOOTING
Check that the line voltage at xture is correct.
1.
Refer to wiring directions.
Is the xture is grounded properly?
2.
Is the photocell is functioning properly (if used)?
3.
Lighting Facts - 5200K
Connect the white xture lead to the (-) COMMON
2.
supply lead.
Connect the bare copper Ground wire from xture to
3.
supply ground.
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool
enough to touch. Do not clean or maintain while
xture is energized.
Clean glass lens with non-abrasive glass cleaning
1.
solution.
Patent pending
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
Lighting Facts - 2800K
WPLED10-IN-1009
Loading...