Page 1
ANGSHARK ACCESSORY INSTRUCTIONS
Easy Installation & Product Help
©2015 RAB LIGHTING Inc.
No
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
ANGSHARK INSTALLATION
1. Use appropriate mounting hardware (not supplied) to secure the Corner Bracket (2) to mounting surface as shown in Fig. 1.
Bracket Tabs must face towards each other. Recommended Corner Bracket Distance center to center is 13-5/16” (for 2 feet)
and 35-23/32” (for 4 feet).
2. Secure Snap On Bracket (2) (supplied standard with Housing) to Corner Bracket (2) with Screws provided as shown in Fig. 1.
3. Snap Housing on Snap On Brackets (2). Snap On Brackets (2) latch onto the Grooves on Lens as shown in Fig. 1 to secure
Housing. Fixture installation should look like Fig. 2 upon completion.
Mounting
Bracket Tab
Screw
Housing
Fig. 1
Surface
Distance
Corner
Bracket (2)
Snap On
Bracket (2)
(supplied
standard w/
Housing)
Lens
Fig. 2
Groove
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
rthvale, New Jersey 07647 USA
ANGSHARK IN 1015
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Page 2
CMSHARK ACCESSORY INSTRUCTIONS
Easy Installation & Product Help
©2015 RAB LIGHTING Inc.
No
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
CMSHARK INSTALLATION
1. Secure each Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location as shown in Fig. 1.
2. Use appropriate mounting hardware (not supplied) to secure each Bracket B (2) (Fig. 2) to mounting surface. Bracket
Distance measured center to center is 12-19/32” (for 2 feet) and 32” ( for 4 feet) (Fig. 1).
WARNING: To secure Housing, Bracket B (2) must be aligned with each other.
3. Hang one side of Bracket A onto Bracket B and tighten Screw (2) on other side as shown in Fig. 3
Fig. 2
Distance
Bracket B
Bracket A
Fig. 1
Housing
Bracket B
Screw (2)
Fig. 3
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
rthvale, New Jersey 07647 USA
CMSHARK IN 1015
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Page 3
JBSHARK ACCESSORY INSTRUCTIONS
Easy Installation & Product Help
©2015 RAB LIGHTING Inc.
No
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
JBSHARK INSTALLATION
1. Secure Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location
shown in Fig. 1.
2. Use appropriate mounting hardware (not supplied) to secure
the Junction Box Plate (Fig. 2) to Mounting Surface or
junction box (Fig. 3). Check that gasket is fully sealed. Use
Cord Grip provided with xture to feed supply wires in xture.
3. Hang one side of each Bracket A onto Junction Box Plate
and tighten Screws (2) on other side as shown in Fig. 3.
Junction Box Plate
Housing
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
rthvale, New Jersey 07647 USA
JBSHARK IN 1015
Bracket A (2)
Fig. 1
Tech Help Line
Call our experts 888 RAB-1000
Fig. 2
rabweb.com
Visit our website for product info
Mounting
Surface
Junction
Box Plate
Screw (2)
Bracket A (2)
Fig. 3
email
Answered promptly sales@rabweb.com
Page 4
VHOOKSHARK ACCESSORY INSTRUCTIONS
Easy Installation & Product Help
©2015 RAB LIGHTING Inc.
No
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
CAUTION:
• For proper weatherproof function all gaskets must be seated properly and all screws and plugs inserted and
tightened rmly.
• Apply weatherproof silicone sealant around the edge of the Housing. This is especially important with an uneven
ceiling surface.
• Silicone all plugs and unused conduit entries and USE SHARK WITH CONDUIT ONLY.
• FOLLOW ALL SHARK ™ (sold separately) INSTALLATION INSTRUCTIONS
VHOOKSHARK INSTALLATION
1. Secure Bracket A (2) to Housing with screws provided.
WARNING: Brackets must be mounted at exact location shown in Fig. 1.
2. Loop each V-Hook (2) on Bracket A as shown in Fig. 2. Fixture should
look like Fig. 3 when nished with step 2.
3. To suspend Housing, connect each V-Hook to two (2) equal lengths of
chain (not supplied) and/ or appropriate hardware (by others) suitable
for mounting surface. Use chain suitable to support four (4) times the
weight of the xture.
Distance
Bracket A
Fig. 1
Housing
Bracket A (2)
Housing
V-Hook (2)
Fig. 2
Bracket A (2)
V-Hook (2)
Fig. 3
TROUBLESHOOTING
1. Check that line voltage at the xture is correct. Be sure the xture is grounded properly.
2. Refer to wiring, cleaning and maintenance directions on SHARK ™ (sold separately) Installation Instructions.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
rthvale, New Jersey 07647 USA
VHOOKSHARK IN 1015
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Loading...