Page 1
TM
SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place with silicone Washers.
2. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
3. Feed supply wires through Junction Box. Check that the
Gasket is fully sealed.
4. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
5. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
WIRING
Junction Box
(not supplied)
Gasket
Door
Housing
Gasket
Housing
Knock Out Slots
Plug
Leveling Bubble
Washers (2)
Door Screws (2)
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
8 1/8”
1 1/4”
5 5/8”
1 1/4”
8 1/8”
5 5/8”
Lag Bolt
Locations
Drilling
Template
Page 2
TM
SLIM35 POLYSHIELD
SLIM35 WIRE GAURD
SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Cover Plate
Stainless Steel
Screws
Stainless Steel Screws (4)
Figure 1
Stainless Steel Screws (4)
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
Note: Guard and shield may be used together.
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Full Cuto Hood
Figure 2
Stainless Steel
Screws
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
Page 3
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
SLIM 37 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
SLIM37 Cool SLIM37 Neutral SLIM37 Warm
SLIMFC37 Cool SLIMFC37 Neutral SLIMFC37 Warm
SLIM37-IN 0913
Page 4
TM
SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place with silicone Washers.
2. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
3. Feed supply wires through Junction Box. Check that the
Gasket is fully sealed.
4. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
5. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
WIRING
Junction Box
(not supplied)
Gasket
Door
Washers (2)
Housing
Gasket
Housing
Knock Out Slots
Plug
Leveling Bubble
Door Screws (2)
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
13 1/4”
9 5/8”
4 13/16”
Lag Bolt
Locations
5 5/8”8 5/16”
Drilling
Template
Page 5
TM
SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Cover Plate
Stainless Steel
Screws
Stainless Steel Screws (4)
Figure 1
Stainless Steel Screws (4)
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
Note: Guard and shield may be used together.
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Full Cuto Hood
Figure 2
Stainless Steel
Screws
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
Page 6
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
SLIM 57 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
SLIM57 Cool SLIM57 Neutral SLIM57 Warm
SLIMFC57 Cool SLIMFC57 Neutral SLIMFC57 Warm
SLIM57-IN 0913
Page 7
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
SLIM 57 BILEVEL SWITCHING
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
WIRING
1. Bi-level xtures have LED’s wired in rows. The two rows are shown below.
2. Each row has set of leads brought through the back of housing and labeled.
3. Use the leads for switching as needed in your application.
ROW #1
SLIM57/BL-IN-1213
ROW #2
Page 8
TM
SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
To ensure weatherproof seal, apply weatherproof silicone
sealant around the edge of the Housing and/or Junction
Box. This is especially important with an uneven wall
surface. Silicone all plugs and unused conduit entries.
1. Loosen Door Screws and open the Door. Screws will
remain in place with silicone Washers.
2. Knock out appropriate Slots when mounting to junction
box (not supplied) or lag bolt to mounting surface using
locations noted below. Use Leveling Bubble to level
xture.
3. Feed supply wires through Junction Box. Check that the
Gasket is fully sealed.
4. Make sure Housing Gasket is properly seated. Close and
tighten the Door Screws. Silicone all Plugs and unused
conduit entries.
5. If outdoor surface is irregular, use caulk to seal any gaps
around the Housing.
WIRING
Junction Box
(not supplied)
Gasket
Door
Housing
Gasket
Knock Out Slots
Housing
Plug
Leveling Bubble
Washers (2)
Door Screws (2)
Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz.
1. Connect the black xture lead to the (+) LINE supply lead.
2. Connect the white xture lead to the (-) COMMON supply
lead.
3. Connect the GROUND wire from xture to supply
ground.
8 1/4”
1 1/2”
5 3/8”
1 1/2”
1 5/8”
13”
6 1/2”
Lag Bolt
Locations
Drilling
Template
Page 9
TM
SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
GUARD/ SHIELD INSTALLATION
1. Remove left and right Cover Plates as in gure 1 and
discard.
2. Mount wire guard and/ or poly shield with (4) #8-32 x 1/2”
Stainless Steel Screws. Screws are provided with the
accessory.
Cover Plate
Stainless Steel
Screws
Figure 1
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.
1. Clean glass lens & xture with non-abrasive glass cleaning
solution.
2. Do not open xture to clean the LED. Do not touch the LED.
TROUBLESHOOTING
1. Check that the line voltage at xture is correct. Refer to
wiring directions.
2. Is the xture grounded properly?
Stainless Steel Screws (4)
Note: Guard and shield may be used together.
Stainless Steel Screws (4)
FULL CUTOFF/ GUARD/ SHIELD
INSTALLATION
1. Remove (4) Stainless Steel Screws from the Full Cuto
Hood.
2. Mount wire guard and/ or poly shield over the full cuto
hood with (4) #8-32 x 1/2” Stainless Steel Screws as shown
in gure 2. Screws are provided with the accessory.
Full Cuto Hood
Figure 2
Stainless Steel
Screws
Note: Guard, shield and full cuto hood may be used together
with (4) #8-32 x 3/4” stainless steel screws (supplied by others).
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation operation
or maintenance.
Page 10
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
SLIM 62 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
SLIM62 Cool SLIM62 Neutral SLIM62 Warm
SLIMFC62 Cool SLIMFC62 Neutral SLIMFC62 Warm
SLIM62-IN 0913
Page 11
TM
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
©2013 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
SLIM 62 BILEVEL SWITCHING
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
WIRING
1. Bi-level xtures have LED’s wired in rows. The two rows are shown below.
2. Each row has set of leads brought through the back of housing and labeled.
3. Use the leads for switching as needed in your application.
ROW #1
SLIM62/BL-IN-1213
ROW #2
Loading...